Effect of therapeutic dose X rays on mechanical and chemical properties of esthetic dental materials

The aim of this study was to investigate the influence of therapeutic dose X rays on the microhardness (MH) and degree of conversion (DC) of two different esthetic restorative dental materials. The materials were photo-activated with a LED light-curing unit using three cure-times: 5, 20 and 40 seconds. The photo-activation was carried out in two distinct periods: before and after irradiation with doses of 5, 35 and 70 Gy, from a 6 MV X rays beam. In accordance with the methodology used, it was conclude that a therapeutic dose does not have a detrimental effect on the photoinitiator molecules, because the photo-activation occurred after they were irradiated. When the irradiation was applied before photo-activation, the materials showed MH improvement, but when photo-activation was performed after irradiation, there was less improvement. However, there was no correlation between MH and DC. Thus, a therapeutic dose applied to cured material can promote linking and breaking of chain bonds in a non-linear way.

Effect of fibre morphology on flocculation of fibre-cement suspensions

The objective of the present research was to evaluate the effect of fibre morphology (e.g., length, width, fibrillation, broken ends, content of fines and number of fibres per gram) on flocculation and drainage properties of fibre-cement suspensions and on physical properties of the fibre-cement composites. Mechanical refining was used to change the morphological properties of Eucalyptus and Pinus pulps. Results show that the mechanical refining increased the size of the formed flocs and decreased the concentration of free small particles (with dimensions between 1 and 20 pm) as a consequence of the increased fibrillation and content of fines, which increased the capacity of the fibres to capture the mineral particles. High levels of refining were necessary for Pinus pulp to obtain cement retention values similar to those obtained by unrefined Eucalyptus pulp. This is due to the higher number of fibres per gram in Eucalyptus pulp than in Pinus pulp. Pulp refining improved the packing of the particles and, although decreased the drainage rate. it contributed to a less porous structure, which improved the microstructure of the composite. (C) 2009 Elsevier Ltd. All rights reserved.

Nosocomial outbreak by imipenem-resistant metallo-beta-lactamase-producing Pseudomonas aeruginosa in an adult intensive care unit in a Brazilian teaching hospital

Objective: To describe an outbreak of imipenem-resistant metallo-beta-lactamase-producing Pseudomonas aeruginosa, enzyme type bla, by horizontal transmission in patients admitted to a mixed adult ICU. Methods: A case-control study was carried out, including 47 patients (cases) and 122 patients (control) admitted to the mixed ICU of a university hospital in Minas Gerais. Brazil from November 2003 to July 2005. The infection site, risk factors, mortality, antibiotic susceptibility, metallo-beta-lactamase (MBL) production, enzyme type, and clonal diversity were analyzed, Results: A temporal/spatial relationship was detected in most patients (94%), overall mortality was 55.3%, and pneumonia was the predominant infection (85%). The majority of isolates (95%) were resistant to imipenem and other antibiotics, except for polymyxin, and showed MBL production (76.7%). Only bla SPM-1 (33%) was identified in the 15 specimens analyzed. In addition, 4 clones were identified, with a predominance of clone A (61.5%) and B (23.1%). On multivariate analysis, advanced age, mechanical ventilation, tracheostomy, and previous imipenem use were significant risk factors for imipenem-resistant P. aeruginosa infection. Conclusions: Clonal dissemination of MBL-producing P. aeruginosa strains with a spatial/temporal relationship disclosed problems in the practice of hospital infection control, low adherence to hand hygiene, and empirical antibiotic use. (C) 2008 Elsevier Espana, S.L. All rights reserved.

Constipation in intensive care unit: Incidence and risk factors

Purpose: Although gastrointestinal motility disorders are common in critically ill patients, constipation and its implications have received very little attention. We aimed to determine the incidence of constipation to find risk factors and its implications in critically ill patients Materials and Methods: During a 6-month period, we enrolled all patients admitted to an intensive care unit from an universitary hospital who stayed 3 or more days. Patients submitted to bowel surgery were excluded. Results: Constipation occurred in 69.9% of the patients. There was no difference between constipated and not constipated in terms of sex, age, Acute Physiology and Chronic Health Evaluation II, type of admission (surgical, clinical, or trauma), opiate use, antibiotic therapy, and mechanical ventilation. Early (<24 hours) enteral nutrition was associated with less constipation, a finding that persisted at multivariable analysis (P < .01). Constipation was not associated with greater intensive care unit or mortality, length of stay, or days free from mechanical ventilation. Conclusions: Constipation is very common among critically ill patients. Early enteral nutrition is associated with earlier return of bowel function. (C) 2009 Elsevier Inc. All rights reserved.

Short- and long-term survival of patients with metastatic solid cancer admitted to the intensive care unit: prognostic factors

Decisions for intensive care unit (ICU) admissions in patients with advanced cancer are complex, and the knowledge of survival rates and prognostic factors are essential to these decisions. Ours objectives were to describe the short- and long-term survival of patients with metastatic solid cancer admitted to an ICU due to emergencies and to study the prognostic factors presented at ICU admission that could be associated with hospital mortality. We retrospectively analysed the charts of all patients with metastatic solid cancer admitted over a 1-year period. This gave a study sample of 83 patients. The ICU, hospital, 1-year and 2-year survival rates were 55.4%, 28.9%, 12.0% and 2.4% respectively. Thrombocytopenia (odds ratio 26.2; P = 0.006) and simplified acute physiology score (SAPS II) (odds ratio 1.09; P = 0.026) were independent factors associated with higher hospital mortality. In conclusion, the survival rates of patients with metastatic solid cancer admitted to the ICU due to emergencies were low, but of the same magnitude as other groups of cancer patients admitted to the ICU. The SAPS II score and thrombocytopenia on admission were associated with higher hospital mortality. The characteristics of the metastatic disease, such as number of organs with metastasis and central nervous system metastasis were not associated with the hospital mortality.

Benefit of antiretroviral therapy on survival of human immunodeficiency virus-infected patients admitted to an intensive care unit

Objective: To evaluate the impact of antiretroviral therapy (ART) and the prognostic factors for in-intensive care unit (ICU) and 6-month mortality in human immunodeficiency virus (HIV)-infected patients. Design: A retrospective cohort study was conducted in patients admitted to the ICU from 1996 through 2006. The follow-up period extended for 6 months after ICU admission. Setting: The ICU of a tertiary-care teaching hospital at the Universidade de Sao Paulo, Brazil. Participants: A total of 278 HIV-infected patients admitted to the ICU were selected. We excluded ICU readmissions (37), ICU admissions who stayed less than 24 hours (44), and patients with unavailable medical charts (36). Outcome Measure: In-ICU and 6-month mortality. Main Results: Multivariate logistic regression analysis and Cox proportional hazards models demonstrated that the variables associated with in-ICU and 6-month mortality were sepsis as the cause of admission (odds ratio [OR] = 3.16 [95% confidence interval [CI] 1.65-6.06]); hazards ratio [HR] = 1.37 [95% Cl 1.01-1.88)), an Acute Physiology and Chronic Health Evaluation 11 score >19 [OR = 2.81 (95% CI 1.57-5.04); HR = 2.18 (95% CI 1.62-2.94)], mechanical ventilation during the first 24 hours [OR = 3.92 (95% CI 2.20-6.96); HR = 2.25 (95% CI 1.65-3.07)], and year of ICU admission [OR = 0.90 (95% CI 0.81-0.99); HR = 0.92 [95% CI 0.87-0.97)]. CD4 T-cell count <50 cells/mm(3) Was only associated with ICU mortality [OR = 2.10 (95% Cl 1.17-3.76)]. The use of ART in the ICU was negatively predictive of 6-month mortality in the Cox model [HR = 0.50 (95% CI 0.35-0.71)], especially if this therapy was introduced during the first 4 days of admission to the ICU [HR = 0.58 (95% CI 0.41-0.83)]. Regarding HIV-infected patients admitted to ICU without using ART, those who have started this treatment during ICU, stay presented a better prognosis when time and potential confounding factors were adjusted for [HR 0.55 (95% CI 0.31-0.98)]. Conclusions: The ICU outcome of HIV-infected patients seems to be dependent not only on acute illness severity, but also on the administration of antiretroviral treatment. (Crit Care Med 2009; 37: 1605-1611)

Effectiveness of Oral Rinse with Chlorhexidine in Preventing Nosocomial Respiratory Tract Infections among Intensive Care Unit Patients

OBJECTIVE. To evaluate the effectiveness of the oral application of a 0.12% solution of chlorhexidine for prevention of respiratory tract infections among intensive care unit (ICU) patients. DESIGN. The study design was a double-blind, randomized, placebo-controlled trial. SETTING. The study was performed in an ICU in a tertiary care hospital at a public university. PATIENTS. Study participants comprised 194 patients admitted to the ICU with a prospective length of stay greater than 48 hours, randomized into 2 groups: those who received chlorhexidine (n = 98) and those who received a placebo (n = 96). INTERVENTION. Oral rinses with chlorhexidine or a placebo were performed 3 times a day throughout the duration of the patient`s stay in the ICU. Clinical data were collected prospectively. RESULTS. Both groups displayed similar baseline clinical features. The overall incidence of respiratory tract infections (RR, 1.0 [95% confidence interval [CI], 0.63-1.60]) and the rates of ventilator-associated pneumonia per 1,000 ventilator-days were similar in both experimental and control groups (22.6 vs 22.3; P = .95). Respiratory tract infection-free survival time (7.8 vs 6.9 days; P = .61), duration of mechanical ventilation (11.1 vs 11.0 days; P = .61), and length of stay (9.7 vs 10.4 days; P = .67) did not differ between the chlorhexidine and placebo groups. However, patients in the chlorhexidine group exhibited a larger interval between ICU admission and onset of the first respiratory tract infection (11.3 vs 7.6 days; P = .05). The chances of surviving the ICU stay were similar (RR, 1.08 [95% CI, 0.72-1.63]). CONCLUSION. Oral application of a 0.12% solution of chlorhexidine does not prevent respiratory tract infections among ICU patients, although it may retard their onset.

Reliability and Failure Modes of Implant-Supported Y-TZP and MCR Three-Unit Bridges

Purpose: Chipping within veneering porcelain has resulted in high clinical failure rates for implant-supported zirconia (yttria-tetragonal zirconia polycrystals [Y-TZP]) bridges. This study evaluated the reliability and failure modes of mouth-motion step-stress fatigued implant-supported Y-TZP versus palladium-silver alloy (PdAg) three-unit bridges. Materials and Methods: Implant-abutment replicas were embedded in polymethylmethacrylate resin. Y-TZP and PdAg frameworks, of similar design (n = 21 each), were fabricated, veneered, cemented (n = 3 each), and Hertzian contact-tested to obtain ultimate failure load. In each framework group, 18 specimens were distributed across three step-stress profiles and mouth-motion cyclically loaded according to the profile on the lingual slope of the buccal cusp of the pontic. Results: PdAg failures included competing flexural cracking at abutment and/or connector area and chipping, whereas Y-TZP presented predominantly cohesive failure within veneering porcelain. Including all failure modes, the reliability (two-sided at 90% confidence intervals) for a ""mission"" of 50,000 and 100,000 cycles at 300 N load was determined (Alta Pro, Reliasoft, Tucson, AZ, USA). No difference in reliability was observed between groups for a mission of 50,000. Reliability remained unchanged for a mission of 100,000 for PdAg, but significantly decreased for Y-TZP. Conclusions: Higher reliability was found for PdAg for a mission of 100,000 cycles at 300 N. Failure modes differed between materials.

Mechanical Testing of Indirect Composite Materials Directly Applied on Implant Abutments

Purpose: To test the strength to failure and fracture mode of three indirect composite materials directly applied onto Ti-6Al-4V implant abutments vs cemented standard porcelain-fused-to-metal (PFM) crowns. Materials and Methods: Sixty-four locking taper abutments were randomly allocated to four groups and were cleaned in ethanol in an ultrasonic bath for 5 min. After drying under ambient conditions, the abutments were grit blasted and a custom 4-cusp molar crown mold was utilized to produce identical crowns (n = 16 per group) of Tescera (Bisco), Ceramage (Shofu), and Diamond Crown (DRM) according to the manufacturer`s instructions. The porcelain-fused-to-metal crowns were fabricated by conventional means involving the construction and a wax pattern and casting of a metallic coping followed by sintering of increasing layers of porcelain. All crowns were loaded to failure by an indenter placed at one of the cusp tips at a 1 mm/min rate. Subsequently, fracture analysis was performed by means of stereomicroscopy and scanning electron microscopy. One-way ANOVA at 95% level of significance was utilized for statistical analysis. Results: The single load to failure (+/- SD) results were: Tescera (1130 +/- 239 N), Ceramage (1099 +/- 257 N), Diamond Crown (1155 +/- 284 N), and PFM (1081 +/- 243 N). Stereomicroscopy analysis showed two distinct failure modes, where the loaded cusp failed either with or without abutment/metallic coping exposure. SEM analysis of the fractures showed multiple crack propagation towards the cervical region of the crown below a region of plastic deformation at the indenter contact region. Conclusion: The three indirect composites and PFM systems fractured at loads higher than those typically associated with normal occlusal function. Although each material had a different composition and handling technique, no significant differences were found concerning their single load to fracture resistance among composite systems and PFM.

Comparison of physical and mechanical properties of microwave-polymerized acrylic resin after disinfection in sodium hypochlorite solutions

This study evaluated the color stability, surface roughness and flexural strength of a microwave-polymerized acrylic resin after immersion in sodium hypochlorite (NaOCl), simulating 20 min of disinfection daily during 180 days. Forty disk-shaped (15 x 4 mm) and 40 rectangular (65 x 10 x 3 mm) specimens were prepared with a microwave-polymerized acrylic resin (Onda-Cryl). Specimens were immersed in either 0.5% NaOCl, 1% NaOCl, Clorox/Calgon and distilled water (control). Color measurements were determined by a portable colorimeter. Three parallel lines, separated by 1.0 mm, were registered on each specimen before and after immersion procedures to analyze the surface roughness. The flexural strength was measured using a 3-point bending test in a universal testing machine with a 50 kgf load cell and a crosshead speed of 1 mm/min. Data were analyzed statistically by ANOVA and Tukey's test (?=0.05). There was no statistically significant differences (p>0.05) among the solutions for color, surface roughness and flexural strength. It may be concluded that immersion in NaOCl solutions simulating short-term daily use during 180 days did not influence the color stability, surface roughness and flexural strength of a microwave-polymerized acrylic resin.

Comparative study of chemical and mechanical retentive systems for bonding of indirect composite resin to commercially pure titanium

This study evaluated the effect of chemical and mechanical surface treatments for cast metal alloys on the bond strength of an indirect composite resin (Artglass) to commercially pure titanium (cpTi). Thirty cylindrical metal rods (3 mm diameter x 60 mm long) were cast in grade-1 cpTi and randomly assigned to 6 groups (n=5) according to the received surface treatment: sandblasting; chemical treatment; mechanical treatment - 0.4 mm beads; mechanical treatment - 0.6 mm beads; chemical/mechanical treatment - 0.4 mm; and chemical/mechanical treatment - 0.6 mm beads. Artglass rings (6.0 mm diameter x 2.0 mm thick) were light cured around the cpTi rods, according manufacturer's specifications. The specimens were invested in hard gypsum and their bond strength (in MPa) to the rods was measured at fracture with a universal testing machine at a crosshead speed of 2.0 mm/min and 500 kgf load cell. Data were analyzed statistically by one-way ANOVA and Tukey test (a=5%). The surface treatments differed significantly from each other (p<0.05) regarding the recorded bond strengths. Chemical retention and sandblasting showed statistically similar results to each other (p=0.139) and both had significantly lower bond strengths (p<0.05) than the other treatments. In conclusion, mechanical retention, either associated or not to chemical treatment, provided higher bond strength of the indirect composite resin to cpTi.

Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

Influence of light-curing unit systems on shear bond strength and marginal microleakage of composite resin restorations

The aim of the present study was to evaluate the influence of different photopolymerization (halogen, halogen soft-start and LED) systems on shear bond strength (SBS) and marginal microleakage of composite resin restorations. Forty Class V cavities (enamel and dentin margins) were prepared for microleakage assessment, and 160 enamel and dentin fragments were prepared for the SBS test, and divided into 4 groups. Kruskal-Wallis and Wilcoxon tests showed statistically significant difference in microleakage between the margins (p < 0.01) with incisal margins presenting the lowest values. Among the groups, it was observed that, only at the cervical margin, halogen soft-start photo polymerization presented statistically significant higher microleakage values. For SBS test, ANOVA showed no statistical difference (p > 0.05) neither between substrates nor among groups. It was concluded that Soft-Start technique with high intensity end-light influenced negatively the cervical marginal sealing, but the light-curing systems did not influence adhesion.

Mechanical properties and porosity of dental glass-ceramics hot-pressed at different temperatures

The objective of this work was to evaluate biaxial-flexural-strength (σf), Vickers hardness (HV), fracture toughness (K Ic), Young's modulus (E), Poisson's ratio (ν) and porosity (P) of two commercial glass-ceramics, Empress (E1) and Empress 2 (E2), as a function of the hot-pressing temperature. Ten disks were hot-pressed at 1065, 1070, 1075 and 1080 °C for E1; and at 910, 915, 920 and 925 °C for E2. The porosity was measured by an image analyzer software and s f was determined using the piston-on-three-balls method. K Ic and HV were determined by an indentation method. Elastic constants were determined by the pulse-echo method. For E1 samples treated at different temperatures, there were no statistical differences among the values of all evaluated properties. For E2 samples treated at different temperatures, there were no statistical differences among the values of σf, E, and ν, however HV and K Ic were significantly higher for 910 and 915 °C, respectively. Regarding P, the mean value obtained for E2 for 925 °C was significantly higher compared to other temperatures.

Fatal adenoviral necrotizing bronchiolitis case in a post-cardiac surgery intensive care unit

We report a case of a 67 year-old-male patient admitted to the intensive care unit in the post-coronary bypass surgery period who presented cardiogenic shock, acute renal failure and three episodes of sepsis, the latter with pulmonary distress at the 30th post-operative day. The patient expired within five days in spite of treatment with vancomycin, imipenem, colistimethate and amphotericin B. At autopsy severe adenovirus pneumonia was found. Viral pulmonary infections following cardiovascular surgery are uncommon. We highlight the importance of etiological diagnosis to a correct treatment approach.