Role of the interfacial water structure on electrocatalysis: Oxygen reduction on Pt(1 1 1) in methanesulfonic acid

Most of electrocatalytic reactions occur in an aqueous environment. Understanding the influence of water structure on reaction dynamics is fundamental in electrocatalysis. In this work, the role of liquid water structure on the oxygen reduction at Pt(1 1 1) electrode is analyzed in methanesulfonic (MTSA) and perchloric acids. This is because these different anions can exert a different influence on liquid water structure. Results reveal a lower ORR electrode activity in MTSA than in HClO4 solutions and they are discussed in light of anion's influence on water structural ordering. From them, the existence of an outer-sphere, rate determining, step in the ORR mechanism is suggested.

Screen-printed electrode based electrochemical detector coupled with ionic liquid dispersive liquid–liquid microextraction and microvolume back-extraction for determination of mercury in water samples

A novel approach is presented, whereby gold nanostructured screen-printed carbon electrodes (SPCnAuEs) are combined with in-situ ionic liquid formation dispersive liquid–liquid microextraction (in-situ IL-DLLME) and microvolume back-extraction for the determination of mercury in water samples. In-situ IL-DLLME is based on a simple metathesis reaction between a water-miscible IL and a salt to form a water-immiscible IL into sample solution. Mercury complex with ammonium pyrrolidinedithiocarbamate is extracted from sample solution into the water-immiscible IL formed in-situ. Then, an ultrasound-assisted procedure is employed to back-extract the mercury into 10 µL of a 4 M HCl aqueous solution, which is finally analyzed using SPCnAuEs. Sample preparation methodology was optimized using a multivariate optimization strategy. Under optimized conditions, a linear range between 0.5 and 10 µg L−1 was obtained with a correlation coefficient of 0.997 for six calibration points. The limit of detection obtained was 0.2 µg L−1, which is lower than the threshold value established by the Environmental Protection Agency and European Union (i.e., 2 µg L−1 and 1 µg L−1, respectively). The repeatability of the proposed method was evaluated at two different spiking levels (3 and 10 µg L−1) and a coefficient of variation of 13% was obtained in both cases. The performance of the proposed methodology was evaluated in real-world water samples including tap water, bottled water, river water and industrial wastewater. Relative recoveries between 95% and 108% were obtained.

Isothermal (liquid + liquid) equilibrium data at T = 313.15 K and isobaric (vapor + liquid + liquid) equilibrium data at 101.3 kPa for the ternary system (water + 1-butanol + p-xylene)

The (vapor + liquid), (liquid + liquid) and (vapor + liquid + liquid) equilibria of the ternary system (water + 1-butanol + p-xylene) have been determined. (Water + 1-butanol + p-xylene) is a type 2 heterogeneous ternary system with partially miscible (water + 1-butanol) and (water + p-xylene) pairs. By contrast, (1-butanol + p-xylene) is totally miscible under atmospheric conditions. This paper examines the (vapor + liquid) equilibrium in both heterogeneous and homogeneous regions at 101.3 kPa of pressure. (Liquid + liquid) equilibrium data at T = 313.15 K have also been determined, and for comparison, the obtained experimental data have been calculated by means of several thermodynamic models: UNIQUAC, UNIFAC and NRTL. Some discrepancies were found between the (vapor + liquid + liquid) correlations; however, the models reproduced the (liquid + liquid) equilibrium data well. The obtained data reveal a ternary heterogeneous azeotrope with mole fraction composition: 0.686 water, 0.146 1-butanol and 0.168 p-xylene.

Removal of BrO3 − from drinking water samples using newly developed agricultural waste-based activated carbon and its determination by ultra-performance liquid chromatography-mass spectrometry

Activated carbon was prepared from date pits via chemical activation with H3PO4. The effects of activating agent concentration and activation temperature on the yield and surface area were studied. The optimal activated carbon was prepared at 450 °C using 55 % H3PO4. The prepared activated carbon was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric-differential thermal analysis, and Brunauer, Emmett, and Teller (BET) surface area. The prepared date pit-based activated carbon (DAC) was used for the removal of bromate (BrO3 −). The concentration of BrO3 − was determined by ultra-performance liquid chromatography-mass tandem spectrometry (UPLC-MS/MS). The experimental equilibrium data for BrO3 − adsorption onto DAC was well fitted to the Langmuir isotherm model and showed maximum monolayer adsorption capacity of 25.64 mg g−1. The adsorption kinetics of BrO3 − adsorption was very well represented by the pseudo-first-order equation. The analytical application of DAC for the analysis of real water samples was studied with very promising results.