Monitorización de la subsidencia del terreno en la Vega Media del río Segura mediante Interferometría SAR diferencial (DInSAR)

Ground subsidence caused by aquifer exploitation is a geotechnical hazard that affects wide areas, causing important economic damages. This phenomenon is due to soil consolidation produced by the increase of effective stress caused by piezometric depletion. In this work a Remote Sensing Technique called Coherent Pixel (CPT) is applied to monitor subsidence in the Vega Media of the Segura River during a period of eleven years.

Procedimiento gráfico para la obtención de los parámetros de corrección del SMR a través de la proyección estereográfica

El Slope Mass Rating (SMR, Romana, 1985) constituye una clasificación geomecánica de uso muy extendido para la caracterización de taludes en roca. Se obtiene por adición al índice RMR básico, calculado a partir de valores característicos del macizo rocoso, de una serie de factores de corrección dependientes del paralelismo discontinuidad-talud, del buzamiento de las discontinuidades, del buzamiento relativo entre las discontinuidades y el talud, así como del método de excavación empleado. En este trabajo se propone un método gráfico que permite obtener los parámetros de corrección del SMR (F1, F2 y F3) representando en proyección estereográfica los planos de discontinuidad y del talud a estudiar.

Elaboración de un mapa de inventario de inestabilidades de los taludes del Polígono Industrial Santiago Payá (Alcoy, Alicante)

Los mapas de inventario de movimientos de ladera se realizan durante las primeras etapas de investigación de los procesos de inestabilidad de laderas y de zonas inestables. Estos mapas resultan de gran utilidad dado que facilitan las tareas de prevención y el análisis de estabilidad. En el presente trabajo se muestra la metodología seguida para elaborar un mapa de inventario de movimientos de ladera en el Polígono Industrial de Santiago Payá situado en el término municipal de Alcoy (Alicante) así como la cartografía resultante.

Técnicas de Ingeniería Cartográfica empleadas en el estudio de subsidencia y movimientos de ladera: principales características y análisis comparativo

Los movimientos de ladera y los procesos de subsidencia son fenómenos que afectan a la superficie terrestre produciendo modificaciones importantes sobre ella. Los cambios que originan se manifiestan como deformaciones superficiales cuyo estudio resulta de gran importancia en el campo de la Ingeniería Geología y la Geotecnia. En el presente trabajo se lleva a cabo una descripción de las técnicas de Ingeniería Cartográfica (técnicas topográficas, geodésicas, fotogramétricas y de teledetección) empleadas para cuantificar las deformaciones causadas por movimientos de ladera y subsidencia terrestre, estableciendo sus principales características y llevando a cabo un análisis comparativo de las mismas.

Forensic analysis of buildings affected by mining subsidence based on Differential Interferometry (Part III)

This work presents a forensic analysis of buildings affected by mining subsidence, which is based on deformation data obtained by Differential Interferometry (DInSAR). The proposed test site is La Union village (Murcia, SE Spain) where subsidence was triggered in an industrial area due to the collapse of abandoned underground mining labours occurred in 1998. In the first part of this work the study area was introduced, describing the spatial and temporal evolution of ground subsidence, through the elaboration of a cracks map on the buildings located within the affected area. In the second part, the evolution of the most significant cracks found in the most damaged buildings was monitored using biaxial extensometric units and inclinometers. This article describes the work performed in the third part, where DInSAR processing of satellite radar data, available between 1998 and 2008, has permitted to determine the spatial and temporal evolution of the deformation of all the buildings of the study area in a period when no continuous in situ instrumental data is available. Additionally, the comparison of these results with the forensic data gathered in the 2005–2008 period, reveal that there is a coincidence between damaged buildings, buildings where extensometers register significant movements of cracks, and buildings deformation estimated from radar data. As a result, it has been demonstrated that the integration of DInSAR data into forensic analysis methodologies contributes to improve significantly the assessment of the damages of buildings affected by mining subsidence.

Partial collapse of a ventilated stone façade: Diagnosis and analysis of the anchorage system

The mechanical behaviour of transventilated façades performed by natural stone is necessarily based on the correct execution of both anchoring elements on the stone cladding as in the ones corresponding to the enclosure support, either with brick masonry walls or reinforced concrete walls. In the case studied in the present work, the origin of the damages suffered on the façade of a building located in Alcoy has been analyzed, where the detachment of part of the outer enclosure occurred. This enclosure is a transventilated façade formed by Bateig Blue stone tiles. To this end, “in situ” tests of the anchoring systems employed have been performed, as well as laboratory tests of mechanical characterization of the material and of different types of anchor, comparing these results with those obtained in both the simplified analytical models of continuum mechanics as developed by the Finite Element Method (FEM).

Estudio de la fluencia de una calcarenita: la Piedra de San Julián (Alicante)

La fluencia de las rocas tiene gran importancia en la evaluación del comportamiento a largo plazo de elementos construidos con estos materiales. En este trabajo, se ha caracterizado física y mecánicamente una calcarenita porosa bien conocida localmente como Piedra de San Julián. Se han realizado ensayos de compresión uniaxial de 96 h. a carga constante. Se ha utilizado un modelo de fluencia bien conocido, el Código-modelo CEB-FIP 2010, usado para modelizar otro material pétreo (hormigón). Además, se ha propuesto un modelo reológico. El objetivo principal de este trabajo es investigar la posibilidad de aprovechar la gran experiencia acumulada en el estudio del hormigón, con el fin de obtener un enfoque para el comportamiento de la roca, para tiempos de prueba muy largos difíciles de implementar en laboratorio. Se propone una función de fluencia adaptada a la roca estudiada dependiente sólo de sus características elásticas y mecánicas.

Uso potencial de ceniza de lodo de depuradora como sustitución de árido fino en bloques de hormigón prefabricados

El presente artículo se centra en la valorización de las cenizas de lodo de depuradora adicionadas en bloques de hormigón prefabricados, por tanto, en una matriz a base de cemento Portland con características particulares (consistencia seca). Se realiza una experiencia piloto mediante la fabricación de bloques en una planta industrial local, utilizando mezclas con porcentajes de sustitución de árido fino del 5, 10 y 15% por cenizas de lodo de depuradora, cuyos resultados se compararán con bloques de referencia (sin adición). Los ensayos aplicados son los preceptivos para su comercialización según normativa europea (marcado CE), lo que permitirá igualmente comprobar las características físicas y mecánicas de los hormigones. Los resultados obtenidos son prometedores: la utilización de este residuo permitiría su comercialización, mejora características de los bloques como la resistencia a compresión, y permitiría reducir un gran volumen de material utilizado habitualmente como materia prima y consumir un residuo destinado a vertedero.

Applying reactive models to column experiments to assess the hydrogeochemistry of seawater intrusion: optimising ACUAINTRUSION and selecting cation exchange coefficients with PHREEQC

Three sets of laboratory column experimental results concerning the hydrogeochemistry of seawater intrusion have been modelled using two codes: ACUAINTRUSION (Chemical Engineering Department, University of Alicante) and PHREEQC (U.S.G.S.). These reactive models utilise the hydrodynamic parameters determined using the ACUAINTRUSION TRANSPORT software and fit the chloride breakthrough curves perfectly. The ACUAINTRUSION code was improved, and the instabilities were studied relative to the discretisation. The relative square errors were obtained using different combinations of the spatial and temporal steps: the global error for the total experimental data and the partial error for each element. Good simulations for the three experiments were obtained using the ACUAINTRUSION software with slight variations in the selectivity coefficients for both sediments determined in batch experiments with fresh water. The cation exchange parameters included in ACUAINTRUSION are those reported by the Gapon convention with modified exponents for the Ca/Mg exchange. PHREEQC simulations performed using the Gains-Thomas convention were unsatisfactory, with the exchange coefficients from the database of PHREEQC (or range), but those determined with fresh water – natural sediment allowed only an approximation to be obtained. For the treated sediment, the adjusted exchange coefficients were determined to improve the simulation and are vastly different from those from the database of PHREEQC or batch experiment values; however, these values fall in an order similar to the others determined under dynamic conditions. Different cation concentrations were simulated using two different software packages; this disparity could be attributed to the defined selectivity coefficients that affect the gypsum equilibrium. Consequently, different calculated sulphate concentrations are obtained using each type of software; a smaller mismatch was predicted using ACUAINTRUSION. In general, the presented simulations by ACUAINTRUSION and PHREEQC produced similar results, making predictions consistent with the experimental data. However, the simulated results are not identical to the experimental data; sulphate (total S) is overpredicted by both models, most likely due to such factors as the kinetics of gypsum, the possible variations in the exchange coefficients due to salinity and the neglect of other processes.

Redes de seguridad para cierre vertical de fachadas

Entre otros medios de protección colectiva, en los últimos años se vienen utilizando en España redes verticales de cierre de fachadas, a paño completo entre forjados en fase de estructura, y también para huecos menores como ventanas o puertas, en fases posteriores. Este tipo de protección no cuenta hasta el momento con ningún tipo de regulación oficial, si bien en el grupo de trabajo AEN/CTN81/SC2/GT7 se desarrolla actualmente el borrador de la norma Pr UNE 81651 a tal fin. Desde el Dtº. de Ing. de la Construcción de la Universidad de Alicante, varios miembros del grupo de trabajo han desarrollado, contando con la experiencia en otros sistemas de protección, algunos modelos numéricos con elementos finitos para valorar y cuantificar variables mecánicas asociadas al episodio de una eventual caída de una persona sobre este tipo de redes, caracterizado por una menor energía cinética que para otros tipos de ellas. En el artículo se exponen los resultados obtenidos para ambos tipos de paños, grandes y pequeños, donde se han valorado la separación de anclajes de la red, las aberturas generadas en su perímetro durante la retención, los esfuerzos en anclajes y elementos textiles, el factor de impacto que sufriría el accidentado y la repercusión de la disposición geométrica de la red, al cuadro o al rombo.

Durability and compressive strength of blast furnace slag-based cement grout for special geotechnical applications

Special foundations, most prominently micropiles and soil anchors, are frequently used in construction today. In Spain, the grout for these special technical applications is generally prepared with portland cement, although the codes and standards in place stipulate only the minimum compressive strength required, with no mention of cement type. Those texts also establish a range of acceptable water:cement ratios. In the present study, durability and compressive strength in cement grout prepared with blast furnace slag cement at different w/c ratios are characterised and compared to the findings for a reference portland cement grout. The results show that slag grout exhibits greater durability than the portland cement material and complies with the compressive strength requirements laid down in the respective codes.

Spatiotemporal characteristics of the Huangtupo landslide in the Three Gorges region (China) constrained by radar interferometry

The Huangtupo landslide is one of the largest in the Three Gorges region, China. The county-seat town of Badong, located on the south shore between the Xiling and Wu gorges of the Yangtze River, was moved to this unstable slope prior to the construction of the Three Gorges Project, since the new Three Gorges reservoir completely submerged the location of the old city. The instability of the slope is affecting the new town by causing residential safety problems. The Huangtupo landslide provides scientists an opportunity to understand landslide response to fluctuating river water level and heavy rainfall episodes, which is essential to decide upon appropriate remediation measures. Interferometric Synthetic Aperture Radar (InSAR) techniques provide a very useful tool for the study of superficial and spatially variable displacement phenomena. In this paper, three sets of radar data have been processed to investigate the Huangtupo landslide. Results show that maximum displacements are affecting the northwest zone of the slope corresponding to Riverside slumping mass I#. The other main landslide bodies (i.e. Riverside slumping mass II#, Substation landslide and Garden Spot landslide) exhibit a stable behaviour in agreement with in situ data, although some active areas have been recognized in the foot of the Substation landslide and Garden Spot landslide. InSAR has allowed us to study the kinematic behaviour of the landslide and to identify its active boundaries. Furthermore, the analysis of the InSAR displacement time-series has helped recognize the different displacement patterns on the slope and their relationships with various triggering factors. For those persistent scatterers, which exhibit long-term displacements, they can be decomposed into a creep model (controlled by geological conditions) and a superimposed recoverable term (dependent on external factors), which appears closely correlated with reservoir water level changes close to the river's edge. These results, combined with in situ data, provide a comprehensive analysis of the Huangtupo landslide, which is essential for its management.

Estudio de la influencia de la temperatura en las propiedades físicas y mecánicas de la calcarenita de San Julián

En este trabajo se muestran los resultados de una serie de ensayos de laboratorio realizados para estudiar el efecto de las altas temperaturas en las propiedades físicas y mecánicas de una calcarenita muy usada como material de construcción en edificios y monumentos históricos de la ciudad de Alicante. El objetivo es evaluar el daño térmico producido en el material al exponerlo a diferentes temperaturas y la influencia de los diferentes procesos de enfriamiento (al aire y por inmersión en agua), así como la viabilidad del diagnóstico del daño mediante métodos no destructivos (ultrasonidos). Se han utilizado probetas cilíndricas extraídas de bloques de roca sobre las que se han realizado ensayos de caracterización del material intacto obteniendo la porosidad, velocidades de propagación de las ondas P y S, módulos dinámicos y estáticos y resistencia a compresión uniaxial. El calentamiento se ha efectuado en horno eléctrico a temperaturas de entre 105 y 600ºC, en intervalos de 100ºC. Para cada temperatura (excepto 105 ºC) se han calentado diez probetas, enfriándolas posteriormente mediante dos procesos diferentes, obteniendo datos de un total de 55 probetas sometidas a diferentes condiciones de temperatura y método de enfriamiento. Finalmente, se han determinado de nuevo las propiedades de las probetas tras su calentamiento, comparando y correlacionando las diferentes variables. Las conclusiones principales destacan un acusado descenso de los valores de las propiedades medidas con la temperatura (excepto la porosidad que aumenta). Este descenso se acelera notablemente con enfriamiento por agua. Los ensayos no destructivos detectan el deterioro producido en el proceso de igual forma que los destructivos.

Radar interferometry techniques for the study of ground subsidence phenomena: a review of practical issues through cases in Spain

Subsidence related to multiple natural and human-induced processes affects an increasing number of areas worldwide. Although this phenomenon may involve surface deformation with 3D displacement components, negative vertical movement, either progressive or episodic, tends to dominate. Over the last decades, differential SAR interferometry (DInSAR) has become a very useful remote sensing tool for accurately measuring the spatial and temporal evolution of surface displacements over broad areas. This work discusses the main advantages and limitations of addressing active subsidence phenomena by means of DInSAR techniques from an end-user point of view. Special attention is paid to the spatial and temporal resolution, the precision of the measurements, and the usefulness of the data. The presented analysis is focused on DInSAR results exploitation of various ground subsidence phenomena (groundwater withdrawal, soil compaction, mining subsidence, evaporite dissolution subsidence, and volcanic deformation) with different displacement patterns in a selection of subsidence areas in Spain. Finally, a cost comparative study is performed for the different techniques applied.

A new approach for semi-automatic rock mass joints recognition from 3D point clouds

Rock mass characterization requires a deep geometric understanding of the discontinuity sets affecting rock exposures. Recent advances in Light Detection and Ranging (LiDAR) instrumentation currently allow quick and accurate 3D data acquisition, yielding on the development of new methodologies for the automatic characterization of rock mass discontinuities. This paper presents a methodology for the identification and analysis of flat surfaces outcropping in a rocky slope using the 3D data obtained with LiDAR. This method identifies and defines the algebraic equations of the different planes of the rock slope surface by applying an analysis based on a neighbouring points coplanarity test, finding principal orientations by Kernel Density Estimation and identifying clusters by the Density-Based Scan Algorithm with Noise. Different sources of information —synthetic and 3D scanned data— were employed, performing a complete sensitivity analysis of the parameters in order to identify the optimal value of the variables of the proposed method. In addition, raw source files and obtained results are freely provided in order to allow to a more straightforward method comparison aiming to a more reproducible research.