Effect of sample geometry on regression rate of the melting interface for carbon steel burned in oxygen

Promoted-ignition testing on carbon steel rods of varying cross-sectional area and shape was performed in high pressure oxygen to assess the effect of sample geometry on the regression rate of the melting interface. Cylindrical and rectangular geometries and three different cross sections were tested and the regression rates of the cylinders were compared to the regression rates of the rectangular samples at test pressures around 6.9 MPa. Tests were recorded and video analysis used to determine the regression rate of the melting interface by a new method based on a drop cycle which was found to provide a good basis for statistical analysis and provide excellent agreement to the standard averaging methods used. Both geometries tested showed the typical trend of decreasing regression rate of the melting interface with increasing cross-sectional area; however, it was shown that the effect of geometry is more significant as the sample's cross sections become larger. Discussion is provided regarding the use of 3.2-mm square rods rather than 3.2-mm cylindrical rods within the standard ASTM test and any effect this may have on the observed regression rate of the melting interface.

Crystallography of carbide-free bainite in a hard bainitic steel

The convergent beam Kikuchi line diffraction technique has been used to accurately determine the orientation relationships between bainitic ferrite and retained austenite in a hard bainitic steel. A reproducible orientation relationship has been uniquely observed for both the upper and lower bainite. It is [GRAPHICS] However, the habit plane of upper bainite is different from that of lower bainite. The former has habit plane that is either within 5 degrees of (221)(A) or of (259)(A). The latter only corresponds with a habit plane that is within 5 degrees of (259)(A). The determined orientation relationship is completely consistent with reported results determined using the same technique with an accuracy of +/- 0.5 degrees in lath martensite in an Fe-20 wt.% Ni-6 wt.% Mn alloy and in a low carbon low alloy steel. It also agrees well with the orientation relationship between granular bainite and austenite in an Fe-19 wt.% Ni-3.5 wt.% Mn-0.15 wt.% C steel. Hence it is believed that, at least from a crystallographic point view, the bainite transformation has the characteristics of martensitic transformation. (c) 2006 Elsevier B.V. All rights reserved.

Electrodeposition of composite copper/liquid-containing microcapsule coatings

This paper presents results on the preparation of microcapsules containing liquid organosilica, and their co-deposition with copper in an acidic copper electrolyte onto a carbon steel cathode to form a copper/microcapsule composite coating. Microscopic analyses of the surface and the cross-section of the coating confirm the incorporation of the liquid-containing microcapsules in the coating layer. The influence of microcapsules in the electrolyte on the cathode polarization, as well as that of process conditions on the microcapsule inclusion, is also discussed. (C) 2004 Kluwer Academic Publishers.

A unique behavior of sub-critical hydrocarbon permeability in activated carbon at low pressures

In our study on sub-critical hydrocarbon permeation in activated carbon, a minimum in the total permeability (B-T) at low pressure has been observed for only long-chain hydrocarbons such as n-hexane and n-heptane. Such an observation suggests that the minimum appearance depends on the properties of permeating vapors as well as the porous medium. In this paper a permeation model is presented to explain the minimum behavior with the allowance of the collision-reflection factor in the Knudsen diffusivity to be a function of surface loading. Surface diffusion was found to be very significant compared to other transport mechanisms such as Knudsen diffusion and gaseous viscous flow at low pressures. Since the gaseous viscous flow contributes negligibly to the B, at low pressures, the minimum appearance in the B, is mainly attributed to the interplay between Knudsen diffusion and surface diffusion. Also, the molecular structure of adsorbates plays an important role in the minimum appearance.

Effects of adsorbed phase on diffusion of subcritical hydrocarbons in activated carbon at low pressures

Diffusions of free and adsorbed molecules of subcritical hydrocarbons in activated carbon were investigated to study the influence of adsorbed molecules on both diffusion processes at low pressures. A collision reflection factor, defined as the fraction of molecules undergoing collision to the solid surface over reflection from the surface, is incorporated into Knudsen diffusivity and surface diffusivity in meso/macropores. Since the porous structure of activated carbon is bimodal in nature, the diffusion of adsorbed molecules is contributed by that of weakly adsorbed molecules on the meso/macropore surfaces and that of strongly adsorbed molecules in the small confinement of micropores. The mobility of adsorbed molecules on the meso/macropore surface is characterized by the surface diffusivity D-mu 2, while that in the micropore is characterized by D-mu 1. In our study with subcritical hydrocarbons, we have found that the former increases almost linearly with pressure, while the latter exhibits a sharp increase at a very low-pressure region and then decreases beyond a critical pressure. This critical pressure is identified as a pressure at which the micropores are saturated.