Investigation of the starch gelatinisation phenomena in water-glycerol systems: application of modulated temperature differential scanning calorimetry

The use of modulated temperature differential scanning calorimetry (MTDSC) has provided further insight into the gelatinisation process since it allows the detection of glass transition during gelatinisation process. It was found in this work that the glass transition overlapped with the gelatinisation peak temperature for all maize starch formulations studied. Systematic investigation on maize starch gelatinisation over a range of water-glycerol concentrations with MTDSC revealed that the addition of glycerol increased the gelatinisation onset temperature with an extent that depended on the water content in the system. Furthermore, the addition of glycerol promoted starch gelatinisation at low water content (0.4 g water/g dry starch) and the enthalpy of gelatinisation varied with glycerol concentration (0.73-19.61 J/g dry starch) depending on the water content and starch type. The validities of published gelatinisation models were explored. These models failed to explain the glass transition phenomena observed during the course of gelatinisation and failed to describe the gelatinisation behaviour observed over the water-glycerol concentrations range investigated. A hypothesis for the mechanisms involved during gelatinisation was proposed based on the side chain liquid crystalline polymer model for starch structure and the concept that the order-disorder transition in starch requires that the hydrogen bonds (the major structural element in the granule packing) to be broken before the collapse of order (helix-coil transition) can take place. (C) 2004 Elsevier Ltd. All rights reserved.

Wheat grain cooking process as investigated by modulated temperature differential scanning calorimetry

The thermal properties of soft and hard wheat grains, cooked in a steam pressure cooker, as a function of cooking temperature and time were investigated by modulated temperature differential scanning calorimetry (MTDSC). Four cooking temperatures (110, 120, 130 and 140 degrees C) and six cooking times (20, 40, 60, 80, 100 and 120 min) for each temperature were studied. It was found that typical non-reversible heat flow thermograms of cooked and uncooked wheat grains consisted of two endothermic baseline shifts localised around 40-50 degrees C and then 60-70 degrees C. The second peaks of non-reversible heat flow thermograms (60-70 degrees C) were associated with starch gelatinisation. The degree of gelatinisation was quantified based on these peaks. In this study, starch was completely gelatinised within 60-80 min for cooking temperatures at 110-120 degrees C and within 20 min for cooking temperatures at 130-140 degrees C. MTDSC detected reversible endothermic baseline shifts in most samples, localised broadly around 48-67 degrees C with changes in heat capacity ranging from 0.02 to 0.06 J/g per degrees C. These reversible endothermic baseline shifts are related to the glass transition, which occurs during starch gelatinisation. Data on the specific heat capacity of the cooked wheat samples are provided. (C) 2005 Elsevier Ltd. All rights reserved.

Specific heat capacity of Australian honeys from 35 to 165C as a function of composition using differential scanning calorimetry

Modulated temperature differential scanning calorimetry was used to investigate the specific heat capacity (C-p) of 10 Australian honeys within the processing and handling temperatures. The values obtained were found to be different from the literature values at certain temperatures, and are not predictable by the additive model. The C-p of each honey exhibited a cubic relationship (P < 0.001) with the temperature (T, C). In addition, the moisture (M, %), fructose (F, %) and glucose (G, %) contents of the honeys influenced their C-p. The following equation (r(2) = 0.92) was proposed for estimating C-p of honey, and is recommended for use in the honey industry and in research: C = 996.7 + 1.4 x 10(-3)T + 5.6 x 10(-5)T(2) - 2.4 x 10(-7)T(3) - 56.5M - 25.8F - 31.0G + 1.5(M * F) + 1.8(M * G) + 0.8(F * G) - 4.6 x 10(-2) (M * F * G).

Gelatinisation of starch in mixtures of sugars. II. Application of differential scanning calorimetry

Differential scanning calorimetry was used to investigate the effect of mixtures of glucose and fructose, and five types of honeys on starch gelatinisation. At a 1:1 starch:water ratio, glucose generally increased the enthalpy (DeltaH(gel)) and temperatures (T-onset, T-peak and T-end) of gelatinisation more than fructose. Upon mixing, DeltaH(gel) of the low-temperature endotherm decreased in comparison to the sole sugars, but was fairly constant (7.7 +/- 0.33 J/g dry starch). DeltaH(gel) of the high-temperature endotherm increased with the fructose content. For both endotherms, the gelatinisation temperatures were unchanged (CV less than or equal to 3%) for the mixtures. With the honeys (moisture, 14.9-18.0%; fructose, 37.2-44.0%; glucose, 28.3-31.9%) added at 1.1-4.4 g per g dry starch, the enthalpy and temperatures of gelatinisation did not vary significantly (CV less than or equal to 6%). Typical thermograms are presented, and the results are interpreted in the light of the various proposed mechanisms for starch gelatinisation in sugar-water systems, total sugar content and possible sugar-sugar interactions. The thermograms were broader in the presence of the sugars and honeys, and a biphasic character was consistently exhibited. The application of an exponential equation to the gelatinisation temperatures of the starch-honey mixtures revealed an opposing influence of fructose and glucose during gelatinisation. The mechanism of starch gelatinisation may be better understood if techniques could be perfected to quantify breakage and formation of hydrogen bonds in the starch granules, and suggested techniques are discussed. (C) 2004 Elsevier Ltd. All rights reserved.

Polarised infrared and differential scanning calorimetry studies on oriented vinyl pipe materials

The molecular orientation in a conventionally extruded PVC pipe, a uniaxially oriented PVC pipe and a biaxially oriented PVC pipe has been studied via Infrared dichroism. The degree of order or crystallinity has also been studied by Differential Scanning Calorimetry and also via Infrared Spectroscopy. The fundamental structural difference between the conventional and oriented pipes was that polymer chains were preferentially aligning in the hoop direction for oriented pipes whereas they were fairly isotropic in the conventional pipe with a slight preferential alignment in the axial direction. Analysis of the C-Cl stretching mode indicated that the uniaxially oriented pipe had much higher alignment of the C-Cl bond in the axial direction than the biaxial pipe, which correlates with higher fracture toughness for circumferential cracking in the biaxial pipe. Both DSC and Infrared spectroscopy detected little change in the crystallinity or order in the oriented pipes compared to the conventionally extruded pipes. (C) 2002 Kluwer Academic Publishers.

Estimating the specific heat capacity of starch-water-glycerol systems as a function of temperature and compositions

Increasing interests in the use of starch as biodegradable plastic materials demand, amongst others, accurate information on thermal properties of starch systems particularly in the processing of thermoplastic starch (TPS), where plasticisers (water and glycerol) are added. The specific heat capacity of starch-water-glycerol mixtures was determined within a temperature range of 40-120degreesC. A modulated temperature differential scanning calorimeter (MTDSC) was employed and regression equations were obtained to predict the specific heat capacity as a function of temperature, water and glycerol content for four maize starches of differing amylose content (0 - 85%). Generally, temperature and water content are directly proportional to the specific heat capacity of the systems, but the influence of glycerol content on the thermal property varied according to the starch type.

Miscibility and phase separation in blends of phenolphthalein poly(aryl ether ketone) and poly(ethylene oxide): a differential scanning calorimetric study

Miscibility and phase separation in the blends of phenolphthalein poly(aryl ether ketone) (PPAEK) and poly(ethylene oxide) (PEO) were investigated by means of differential scanning calorimetry (DSC). The PPAEK/PEO blends prepared by solution casting from N,N-dimethylformamide (DMF) displayed single composition-dependent glass transition temperatures (T-g), intermediate between those of the pure components, suggesting that the blend system is miscible in the amorphous state at all compositions. All the blends underwent phase separation at higher temperatures and the system exhibited a lower critical solution temperature (LCST) behavior. A step-heating thermal analysis was designed to determine the phase boundaries with DSC. The significant changes in the thermal properties of blends were utilized to judge the mixing status for the blends and the phase diagram was thus established. (C) 2004 Elsevier B.V. All rights reserved.

Physical aging of amorphous fructose

Physical aging of amorphous anhydrous fructose at temperature 5 degreesC and at 22 degreesC was studied using differential scanning calorimetry (DSC). The dynamic glass transitions temperature, T-g0 for unaged samples was 16 degreesC and 13.3 degreesC for heating rate of 10 degreesC/min and 1 degreesC/min, respectively. The fictive temperature, T-f0 for unaged samples calculated by Richardson and Savill method was 12 degreesC, which is close to the dynamic value obtained from the lower DSC heating rate. The fictive temperature T-f of the aged fructose glasses at temperatures both below and above the transition region was fitted well by a non-exponential decay function (Williams-Watts form). Aging above the transition region (22 degreesC) for 18 d increased both the dynamic glass transition temperature T and the fictive temperature T-f. However, aging below the transition region (5 degreesC) for I d increased the dynamic glass transition temperature T-g but decreased the fictive temperature T-f.

Dynamic and steady-state rheology of Australian honeys at subzero temperatures

The rheology of 10 Australian honeys was investigated at temperatures -15C to 0C by a strain-controlled rheometer. The honeys exhibited Newtonian behavior irrespective of the temperature, and follow the Cox-Merz rule. G/G' and omega are quadratically related, and the crossover frequencies for liquid to solid transformation and relaxation times were obtained. The composition of the honeys correlates well (r(2) > 0.83) with the viscosity, and with 24 7 data sets (Australian and Greek honeys), the following equation was obtained: mu = 1.41 x 10(-17) exp [-1.20M + 0.01F - 0.0G + (18.6 X 10(3)/T)] The viscosity of the honeys showed a strong dependence on temperature, and four models were examined to describe this. The models gave good fits (r(2) > 0.95), but better fits were obtained for the WLF model using T-g of the honeys and mu(g) = 10(11) Pa.s. The WLF model with its universal values poorly predicted the viscosity, and the implications of the measured rheological behaviors of the honeys in their processing and handling are discussed.

Conductivity, NMR and crystallographic study of N,N,N,N-tetramethylammonium dicyanamide plastic crystal phases: an archetypal ambient temperature plastic electrolyte material

N,N,N,N-Tetramethylammonium dicyanamide (Me(4)NDCA) has been examined via differential scanning calorimetry (DSC), thermogravimetric analysis, conductivity, single crystal X-ray diffraction and H-1 nuclear magnetic resonance (NMR) analyses, and was found to be highly conductive in the solid state (sigma = 10(-3) S cm(-2) at 420 K) and to also exhibit unusual plastic crystal behaviour. To investigate the correlation between such behaviour and the occurrence of molecular rotations in the crystal, H-1 NMR second moment measurements are compared with calculated values predicted from the crystal structure. While DSC analysis indicates a number of solid-solid transitions at ambient temperatures, subsequent H-1 NMR analysis of the Me4N+ cation shows that a variety of rotational motions become active at low (

Application of the Williams-Landel-Ferry model to the viscosity-temperature relationship of Australian honeys

The rheological behaviour of nine unprocessed Australian honeys was investigated for the applicability of the Williams-Landel-Ferry (WLF) model. The viscosity of the honeys was obtained over a range of shear rates (0.01-40 s(-1)) from 2degrees to 40 degreesC, and all the honeys exhibited Newtonian behaviour with viscosity reducing as the temperature was increased. The honeys with high moisture were of lower viscosity, The glass transition temperatures of the honeys, as measured with a differential scanning calorimeter (DSC), ranged from -40degrees to -46 degreesC, and four models (WLF. Arrhenius, Vogel-Tammann-Fulcher (VTF), and power-law) were investigated to describe the temperature dependence of the viscosity. The WLF was the most suitable and the correlation coefficient averaged 0.999 +/- 0.0013 as against 0.996 +/- 0.0042 for the Arrhenius model while the mean relative deviation modulus was 0-12% for the WLF model and 10-40% for the Arrhenius one. With the universal values for the WLF constants, the temperature dependence of the viscosity was badly predicted. From non-linear regression analysis, the constants of the WLF models for the honeys were obtained (C-1 = 13.7-21.1: C-2 = 55.9-118.7) and are different from the universal values. These WLF constants will be valuable for adequate modeling of the rheology of the honeys, and they can be used to assess the temperature sensitivity of the honeys. (C) 2002 Elsevier Science Ltd. All rights reserved.

Effect of storage of adzuki bean (Vigna angularis) on starch and protein properties

Differential scanning calorimetry was used to evaluate the effect of storage at 10degreesC, 20degreesC and 30degreesC, and 40% and 65% relative humidity (RH) on adzuki bean starch gelatinisation and protein denaturation temperatures. Storage for 6 months at an elevated storage temperature (30degreesC) caused increases in the starch gelatinisation onset temperature (T-o) and gelatinisation peak temperature (T-p) for both Bloodwood and Erimo varieties. Storage at 40% RH resulted in higher T-o and T-p values than storage at 65% RH. The T-o of starch from Bloodwood and Erimo beans stored for up to 1.5 months at 10degreesC and 65% were similar to those of fresh beans. The changes in the salt-soluble protein component were less clear cut than those of the starch. Nonetheless, protein extracted from beans stored at 40% RH exhibited significantly lower T-o and T-p values compared with those stored at 65% RH. This indicates some destabilisation of the protein at the higher RH. These results suggest that detrimental changes occur in starch and, to a lesser extent protein, of adzuki beans stored under unfavourable conditions. On the basis of these results, the best storage conditions to maintain the characteristics of fresh beans are low temperatures (e.g. 10degreesC) and high RH (e.g. 65%). (C) 2003 Swiss Society of Food Science and Technology. Published by Elsevier Science Ltd. All rights reserved.

Thermal analysis, nuclear magnetic resonance spectroscopy, and impedance spectroscopy of N,N-dimethyl-pyrrolidinium iodide: An ionic solid exhibiting rotator phases

N,N-dimethyl-pyrrolidinium iodide has been investigated using differential scanning calorimetry, nuclear magnetic resonance (NMR) spectroscopy, second moment calculations, and impedance spectroscopy. This pyrrolidinium salt exhibits two solid-solid phase transitions, one at 373 K having an entropy change, Delta S, of 38 J mol(-1) K-1 and one at 478 K having Delta S of 5.7 J mol(-1) K-1. The second moment calculations relate the lower temperature transition to a homogenization of the sample in terms of the mobility of the cations, while the high temperature phase transition is within the temperature region of isotropic tumbling of the cations. At higher temperatures a further decrease in the H-1 NMR linewidth is observed which is suggested to be due to diffusion of the cations. (C) 2005 American Institute of Physics.