Ecological distribution of mosquito larvae of the Anopheles punctulatus group on Niolam (Lihir) Island, Papua New Guinea

We surveyed the larval habitats of member,, of the Anopheles punctulatus group of mosquitoes on Niolam (Lihir) Island. Papua New Guinea. Identification of this group was undertaken by polymerase chain reaction-restriction fragment length polymorphism analysis of the amplified internal transcribed spacer unit 2 of rDNA. because morphologic separation of member species is unreliable. The most widespread malaria vector species and their most common larval habitats identified to aid source-reduction programs for malaria control. The most ubiquitous species was An. punctulatus, followed by An. farauti no. 2. then An. farauti s.s. Anopheles punctulatus has increased relative to An.farauti s.l. since the start of development projects on Lihir Island. The most common larval habitats were shallow temporary pools with clay substrate and with plants or floatage. These habitats. mostly encountered alongside poorly drained roads, may be increased by development projects.

Japanese encephalitis on Badu Island, Australia: the first isolation of Japanese encephalitis virus from Culex gelidus in the Australasian region and the role of mosquito host-feeding patterns in virus transmission cycles

During investigation of an outbreak of Japanese encephalitis (JE) in the Torres Strait, Australia, in 2000, mosquitoes were collected in Badu Island community and at a newly established communal piggery about 3 km from the community. A total of 94285 mosquitoes, comprising 91240 (96.8%) unengorged females, 1630 (1.7%) blood-engorged females and 1415 (1.5%) males, were processed for virus isolation. One isolate of JE virus was obtained from Culex gelidus, with a minimum infection rate of 12.4:1000. This is the first isolate of JE virus from Cx. gelidus in the Australasian region. No isolates were obtained from Cx. annulirostris, the primary implicated Australian JE vector. Analysis of mosquito host-feeding patterns, using gel diffusion, demonstrated that Cx. annulirostris and 5 other species fed predominately on mammals, Analysis of blood-fed mosquitoes collected within the community demonstrated that the proportion of Cx. annulirostris feeding on pigs in 2000 (2.3%) was significantly lower than that for the 1995-97 period (31.3%). The removal of the pigs from Badu Island community has limited the contact between potential amplifying hosts and mosquitoes, thus potentially reducing the risk of transmission of JE virus to the human population.

Cultural Specific Training in Corruption Reporting for Pacific Island Journalists

Notes that very few journalists have formal training in corruption reporting. Discusses workshops held in 2000 and 2001 on the subject of corruption reporting for Pacific Island journalists. Explains the role of the media as an anti-corruption mechanism and the difficulty journalists face in identifying and sometimes stamping out corruption. Looks at the programs adopted and explains the responses of journalists.

The effect of heat treatment on the toughness, hardness and microstructure of low carbon white cast irons

The effect of destabilisation and subcritical heat treatment on the impact toughness, hardness, and the amount and mechanical stability of retained austenite in a low carbon white cast iron have been investigated. The experimental results show that the impact energy constantly increases when the destabilisation temperature is raised from 950 degreesC to 1200 degreesC. Although the hardness decreases, the heat-treated hardness is still greater than the as-cast state. After destabilisation treatment at 1130 degreesC, tempering at 200 to 250 degreesC for 3 hours leads to the highest impact toughness, and secondary hardening was observed when tempering over 400 degreesC. The amount of retained austenite increased with the increase in the destabilisation temperature, and the treatment significantly improves the mechanical stability of the retained austenite compared with the as-cast state. Tempering below 400 degreesC does not affect the amount of retained austenite and its mechanical stability. But the amount of retained austenite is dramatically reduced when tempered above 400 degreesC. The relationship between the mechanical properties and the microstructure changes was discussed. (C) 2001 Kluwer Academic Publishers.

Heat of desorption measured by means of electrical heat excitation

A new method of measuring heat of desorption is proposed in this Letter. The principle of the method is to measure the amount of mass released when a controlled amount of energy is supplied directly to a solid adsorbent. This is in contrast to conventional methods such as microcalorimetry, where heat released upon adsorption is measured. In this method, a quantified heat supply is generated by passing a de current through a carbon pellet, which is equilibrated with a gas phase confined in a closed vessel. As a consequence of the heating, the particle temperature is increased, resulting in partial desorption of adsorbed molecules. The variations of pellet temperature and the system pressure with respect to time are used to determine the heat of desorption as a function of loading.