Glass transition in Australian honeys

Differential scanning calorimetry (DSC) was used to study the glass transition in 10 Australian honeys by scanning at 10 degrees Cmin(-1) from -130 to 50 degreesC after annealing at -50 degreesC. The honeys had moisture contents 14.9 to 18.0%, seven were from Eucalyptus species. The glass transition temperatures (T-g) ranged from -46 degrees to -38 degreesC and were significantly (p

The effect of channel geometry and wall boundary conditions on the formation of extrusion surface instabilities for LLDPE

It is believed that surface instabilities can occur during the extrusion of linear low density polyethylene due to high extensional stresses at the exit of the die. Local crack development can occur at a critical stress level when melt rupture is reached. This high extensional stress results from the rearrangement of the flow at the boundary transition between the wall exit and the free surface. The stress is highest at the extrudate surface and decreases into the bulk of the material. The location of the region where the critical level is reached can determine the amplitude of the extrudate surface distortion, This paper studies the effect of wall slip on the numerically simulated extensional stress level at the die exit and correlates this to the experimentally determined amplitude of the surface instability. The effect of die exit radius and die wall roughness on extrusion surface instabilities is also correlated to the exit stress level in the same way. Whereas full slip may completely suppress the surface instability, a reduction in the exit stress level and instability amplitude is also shown for a rounded die exit and a slight increase in instability is shown to result from a rough die wall. A surface instability map demonstrates how the shear rate for onset of extrusion surface instabilities can be predicted on the basis of melt strength measurements and simulated stress peaks at the exit of the die. (C) 2001 Elsevier Science B.V. All rights reserved.

Developing biodegradable mulch films from starch-based polymers

This paper examines the development of starch-based plastics for use as biodegradable mulch film. A variety of starch-based polymers are blended with high performance biodegradable polyester polymers in order to determine the applicability of films to be processed on a film blowing line and to perform well in mulch film field trials. The process of material formulation, film blowing processing and scale-up and performance properties are highlighted for a successful material. Insights into future developments of starch-derived biodegradable polymers are given.

An automated multi-unit composting facility for biodegradability evaluations

A system has been developed for studying the biodegradation of natural and synthetic polymeric material. The system is based on standard methods developed by the European Committee for Standardisation (CEN TC 261) (ISO/DIS 14855) and the American Society of Testing Materials, 'ASTM. Standard Test Method for Determining Aerobic. Biodegradation of Plastic Materials under Controlled Composting Conditions' (ASTM D 5338-92). A new low-cost compost facility has been used which satisfies the requirements of these standards. The system has been automated for data collection and has been run under the conditions specified by the standards. In the system, cellulose, newspaper and two starch-based polymers were treated with compost in a series of 3dm(3) vessels at 52 degreesC and under conditions of optimum moisture and pH. The degradation was followed over time by measuring the amount of carbon released as carbon dioxide. (C) 2001 Society of Chemical Industry.

The effects of silica fillers on the gelation and vitrification of highly filled epoxy-amine thermosets

Highly filled thermosets are used in applications such as integrated circuit (IC) packaging. However, a detailed understanding of the effects of the fillers on the macroscopic cure properties is limited by the complex cure of such systems. This work systematically quantifies the effects of filler content on the kinetics, gelation and vitrification of a model silica-filled epoxy/amine system in order to begin to understand the role of the filler in IC packaging cure. At high cure temperatures (100 degreesC and above) there appears to be no effect of fillers on cure kinetics and gelation and vitrification times. However, a decrease in the gelation and vitrification times and increase the reaction rate is seen with increasing filler content at low cure temperatures (60-90 degreesC). An explanation for these results is given in terms of catalysation of the epoxy amine reaction by hydrogen donor species present on the silica surface and interfacial effects.

Occupational therapists' use and perceptions of written client education materials

OBJECTIVE. The purpose of this study was to examine occupational therapists' use and perceptions of written education materials for clients and the factors that therapists consider before distributing written materials to clients This study also aimed to determine whether use and perceptions of these materials differed for older clients METHOD. A random sample of 50 occupational therapists from Queensland, Australia, working in adult physical disabilities settings was surveyed with a structured questionnaire Data were analyzed descriptively and with nonparametric statistics RESULTS. Of 49 participants who used written materials, 54% had given them to more than halt of their last 10 clients, regardless of the clients' age Written materials, most often information sheets developed by the participants themselves; handwritten notes; and pamphlets were principally used to reinforce verbal information. Clients' cognitive abilities, primary language, communication skills, vision, and level of education most often were considered before distributing written materials Although participants generally were positive about the content and effectiveness of materials, ratings were significantly less positive related to older clients CONCLUSION. Client education was a core treatment modality for participants in this study, with written media most commonly being used to supplement verbal education Because participants were least positive about the effectiveness of written materials for older clients, further development of materials for this audience may be indicated.

Comparative evaluation of juvenoids for control of cat fleas (Siphonaptera : Pulicidae) in topsoil

The efficacy of a photostable formulation of methoprene and two photostable juvenoids, fenoxycarb and pyriproxyfen, and their residual activity in inhibiting the emergence of adult cat fleas, Ctenocephalides felis (Bouche), was studied in topsoil. Nursery pots composed of clay, peat, and plastic, and wooden flats were used to hold soil samples. Treated soil samples were exposed to sunlight during the 63-d study period. Methoprene was as effective as fenoxycarb and pyriproxyfen against cat fleas for up to 42 d in clay, peat, and plastic pots at a concentration of 64.56 mg (AI) /m(2) (6 mg [AI] /ft(2)), but its activity declined significantly thereafter. In contrast, fenoxycarb and pyriproxyfen showed strong residual activity for the entire 63 d. The activity of methoprene declined even more rapidly over time in wooden flats, while at the same concentrations the other two juvenoids showed significant residual activity for 63 d. Clay, peat, and plastic pots were therefore considered to be equally effective for evaluating the outdoor efficacy of juvenoids in comparison to the wooden flats. However, results obtained with wooden flats may be more realistic when testing residual activity of volatile chemicals such as methoprene. Fenoxycarb and pyriproxyfen showed strong efficacy and residual activity at concentrations of 8.07, 16.14, and 32.28 mg (AI) /m(2), whereas methoprene did not cause a significant reduction of adult emergence at levels below 64.56 mg (AI) /m(2). LC50 values for methoprene, fenoxycarb, and pyriproxyfen needed for preventing flea emergence when applied to topsoil were estimated to be 0.643, 0.031, and 0.028 ppm, respectively.

The work of fracture in uniaxial and biaxial oriented unplasticised polyvinylchloride pipes

In oriented unplasticised polyvinylchloride (uPVC) pipes, cracks propagate tangentially rather than through the wall as in conventional pipe. Notched impact, a modified peel test and the specific work of fracture approach have been used to measure fracture toughness of a conventionally extruded, a uniaxially oriented and a biaxially oriented uPVC pipe in different directions. The different failure mode for the oriented pipes was found to result from an order of magnitude increase in the fracture toughness for cracks propagating perpendicular to the orientation direction. Differences in the fracture toughness between the oriented pipes were also related to their molecular orientation. (C) 2002 Elsevier Science Ltd. All rights reserved.

The essential work of fracture through the wall of uPVC pipe

The specific essential work of fracture, w(e), has been measured for a relatively thick walled uPVC pipe as a function of position through the wall of the pipe. w(e) was highest at the surface of the pipe and decreased significantly at the centre of the pipe wall. The variation in w(e) through the wall of the pipe correlated with the processing level of the uPVC material as measured by the critical temperature, T-c. The variability in the measured values of w(e) was substantially higher in the centre of the pipe where the processing levels were lower. This was likely to be a result of the variability in the microstructure of the material where poor processing had introduced regions of poor fusion of primary PVC particles. (C) 2002 Kluwer Academic Publishers.

Polarised infrared and differential scanning calorimetry studies on oriented vinyl pipe materials

The molecular orientation in a conventionally extruded PVC pipe, a uniaxially oriented PVC pipe and a biaxially oriented PVC pipe has been studied via Infrared dichroism. The degree of order or crystallinity has also been studied by Differential Scanning Calorimetry and also via Infrared Spectroscopy. The fundamental structural difference between the conventional and oriented pipes was that polymer chains were preferentially aligning in the hoop direction for oriented pipes whereas they were fairly isotropic in the conventional pipe with a slight preferential alignment in the axial direction. Analysis of the C-Cl stretching mode indicated that the uniaxially oriented pipe had much higher alignment of the C-Cl bond in the axial direction than the biaxial pipe, which correlates with higher fracture toughness for circumferential cracking in the biaxial pipe. Both DSC and Infrared spectroscopy detected little change in the crystallinity or order in the oriented pipes compared to the conventionally extruded pipes. (C) 2002 Kluwer Academic Publishers.

Kinematics of oblique collision and ramping inferred from microstructures and strain in middle crustal rocks, central Southern Alps, New Zealand

The hanging wall of the Alpine Fault near Franz Josef Glacier has been exhumed during the past similar to2-3 m.y. providing a sample of the ductilely deformed middle crust of a modem obliquely convergent orogen. Presently exposed rocks of the Pacific Plate are inferred to have undergone several phases of ductile deformation as they moved westward above a mid-crustal detachment. Initially they were transpressed across the outboard part of the orogen, resulting in oblate fabrics with a down-dip stretch. Later, they encountered the Alpine Fault, experiencing an oblique-slip backshearing on vertical planes. This escalator-like deformation tilted and thinned the incoming crust onto that crustal-scale oblique ramp. This style of hanging wall deformation may affect only the most rapidly uplifting, central part of the Southern Alps because of the low flexural rigidity of the crust in that region and its displacement over a relatively sharp ramp-angle at depth. A 3D transpressive flow affected mylonites locally near the fault, but their shear direction remained parallel to plate motion, ruling out ductile 'extrusion' as an important process in this orogen. Outside the mylonite zone, late Cenozoic shortening is inferred to be modest (30-40%), as measured from deformation of younger biotite grains. Oblique collision is dominated by translation on the Alpine Fault, and rocks migrate rapidly through the deforming zone, preventing the accumulation of large finite strains. Transpression may play a minor role in oblique collision. (C) 2001 Elsevier Science Ltd. All rights reserved.

Benefits, harms and costs of screening mammography in women 70 years and over: a systematic review

Objective: To assess the (i) benefits, (ii) harms and (iii) costs of continuing mammographic screening for women 70 years and over. Data sources and synthesis: (i) We conducted a MEDLINE search (1966 - July 2000) for decision-analytic models estimating life-expectancy gains from screening in older women. The five studies meeting the inclusion criteria were critically appraised using standard criteria. We estimated relative benefit from each model's estimate of effectiveness of screening in older women relative to that in women aged 50-69 years using the same model. (ii) With data from BreastScreen Queensland, we constructed balance sheets of the consequences of screening for women in 10-year age groups (40-49 to 80-89 years), and (iii) we used a validated model to estimate the marginal cost-effectiveness of extending screening to women 70 years and over. Results: For women aged 70-79 years, the relative benefit was estimated as 40%-72%, and 18%-62% with adjustment for the impact of screening on quality of life. For women over 80 years the relative benefit was about a third, and with quality-of-life adjustment only 14%, that in women aged 50-69 years. (ii) Of 10 000 Australian women participating in ongoing screening, about 400 are recalled for further testing, and, depending on age, about 70-112 undergo biopsy and about 19-80 cancers are detected. (iii) Cost-effectiveness estimates for extending the upper age limit for mammographic screening from 69 to 79 years range from $8119 to $27 751 per quality-adjusted life-year saved, which compares favourably with extending screening to women aged 40-49 years (estimated at between $24 000 and $65 000 per life-year saved). Conclusions: Women 70 years and over, in consultation with their healthcare providers, may want to decide for themselves whether to continue mammographic screening. Decision-support materials are needed for women in this age group.

The effects of fillers on the chemorheology of highly filled epoxy resins: I. Effects on cure transitions and kinetics

This work examines the effects of level of silica filler (at 0, 10, 30, 50wt%) on the gelation and vitrification of a model silica-filled diglycidyl ether of bisphenol F (DGEBF)/methylenedianiline (MDA) system. An increased filler level is shown to decrease the gelation and vitrification times at low temperatures (below 80degreesC). FTIR cure kinetics show that the reaction rates are increased and the activation energies of gelation are reduced at these temperatures, indicating that network formation is made easier. Entropic and catalytic reasons for this phenomenon are discussed. (C) 2003 Society of Chemical Industry.