Scavenging of siliceous grain-boundary phase of 8-mol%-ytterbia-stabilized zirconia without additive

The grain-boundary conductivity (sigma (gb),) of 8-mol%-ytterbiastabilized zirconia increased markedly with heat treatment between 1000 degrees and 1300 degreesC with a slow heating rate (0.1 degreesC/min) before sintering. The extent of the sigma (gb) improvement was the same or larger than that via Al2O3 addition. The heat treatment did not affect the grain-interior conduction when sintered at 1600 degreesC, while Al2O3-derived scavenging significantly did, given the larger increment of total conductivity in the heat-treated sample. The formation of a silicon-containing phase in a discrete form was suggested as a possible route of scavenging the resistive phase from the correlation between average grain size and sigma (gb).

Trade and environment: Evidence from China's manufacturing sector

This paper focusing on the Chinese manufacturing sector assesses the environmental impact of trade liberalization in China. The results show that China's experience with the trade liberalization-environment nexus is consistent with international evidence. On one hand, trade liberalization has had various positive effects on the environment. Firstly, it promoted specialization in areas of comparative advantage, which, in general, included industries that contributed less to environmental degradation. Secondly, it allowed China to access and adopt the best international practices in pollution abatement technology. Thirdly, it enabled China to transfer environmental costs to other countries by importing intermediate products whose production contributed to environmental degradation. On the other hand, these positive effects were overwhelmed by a negative scale effect, which was the result of a huge increase in the demand for Chinese exports. The paper concludes that if China is to prevent pollution from reaching a critical threshold, environmental regulations need to be tightened. Copyright (C) 2002 John Wiley & Sons, Ltd and ERP Environment.

Productivity growth in Australian manufacturing sector: some new evidence

This article examines the productivity performance of Australia's manufacturing sector by decomposing its output growth into input growth, technological progress and gains in technical efficiency. This three-way decomposition is done with an improved version of the stochastic frontier model using eight, two-digit industry level data from 1968/9 to 1994/5. Empirical evidence shows that input growth fueled output growth from 1968/9 to 1973/4, but since then, total factor productivity (TFP) growth has been the main contributor of output growth. While the trend of TFP growth was found to be promising for most industries with positive and increasing technological progress, the negative gains from technical efficiency over time is however cause for concern.

Evolution of additive and nonadditive genetic variance in development time along a cline in Drosophila serrata

Latitudinal clines provide natural systems that may allow the effect of natural selection on the genetic variance to be determined. Ten clinal populations of Drosophila serrata collected from the eastern coast of Australia were used to examine clinal patterns in the trait mean and genetic variance of the life-history trait egg-to-adult development time. Development time significantly lengthened from tropical areas to temperate areas. The additive genetic variance for development time in each population was not associated with latitude but was associated with the population mean development time. Additive genetic variance tended to be larger in populations with more extreme development times and appeared to be consistent with allele frequency change. In contrast, the nonadditive genetic variance was not associated with the population mean but was associated with latitude. Levels of nonadditive genetic variance were greatest in the region of the cline where the gradient in the change in mean was greatest, consistent with Barton's (1999) conjecture that the generation of linkage disequilibrium may become an important component of the genetic variance in systems with a spatially varying optimum.

Measuring range of active cervical rotation in a position of full head flexion using the 3D Fastrak measurement system: an intra-tester reliability study

Most external assessments of cervical range of motion assess the upper and lower cervical regions simultaneously. This study investigated the within and between days reliability of the clinical method used to bias this movement to the upper cervical region, namely measuring rotation of the head and neck in a position of full cervical flexion. Measurements were made using the Fastrak measurement system and were conducted by one operator. Results indicated high levels of within and between days repeatability (range of ICC2,1 values: 0.85-0.95). The ranges of axial rotation to right and left, measured with the neck positioned in full flexion, were approximately 56% and 50%, respectively of total cervical rotation, which relates well to the proportional division of rotation in the upper and lower cervical regions. These results suggest that this method of measuring rotation would be appropriate for use in subject studies where movement dysfunction is present in the upper cervical region, such as those with cervicogenic headache. (C) 2003 Elsevier Science Ltd. All rights reserved.