Materiais à base de óxidos com estrutura do tipo perovskite e compósitos como ânodos de PCES

This work was focused on the analysis of transport, thermomechanical and electrochemical properties of a series of perovskite-like oxide materials and composites for potential applications as anodes of intermediate-temperature solid oxide fuel cells (SOFCs) with lanthanum gallate and silicate solid electrolytes. The primary attention was centered on A(Mn,Nb)O3-δ (A = Sr, Ca) and (La,Sr)(Mn,Ti)O3-based systems, lanthanum chromite substituted with acceptor-type and variable-valence cations, and various Ni-containing cermets. Emphasis was given to phase stability of the materials, their crystal structure, microstructure of porous electrode layers and dense ceramics, electronic conductivity, Seebeck coefficient, oxygen permeability, thermal and chemical induced expansion, and anodic overpotentials of the electrodes deposited onto (La,Sr)(Ga,Mg)O3- and La10(Si,Al)6O27- based electrolyte membranes. In selected cases, roles of oxygen diffusivity, states of the transition metal cations relevant for the electronic transport, catalytically active additives and doped ceria protective interlayers introduced in the model electrochemical cells were assessed. The correlations between transport properties of the electrode materials and electrochemical behavior of porous electrodes showed that the principal factors governing anode performance include, in particular, electronic conduction of the anode compositions and cation interdiffusion between the electrodes and solid electrolytes. The latter is critically important for the silicatebased electrolyte membranes, leading to substantially worse anode properties compared to the electrochemical cells with lanthanum gallate solid electrolyte. The results made it possible to select several anode compositions exhibiting lower area-specific electrode resistivity compared to known analogues, such as (La,Sr)(Cr,Mn)O3-δ.

Anodes for protonic ceramic fuel cells (PCFCs)

One of the more promising possibilities for future “green” electrical energy generation is the protonic ceramic fuel cell (PCFC). PCFCs offer a low-pollution technology to generate electricity electrochemically with high efficiency. Reducing the operating temperature of solid oxide fuel cells (SOFCs) to the 500-700°C range is desirable to reduce fabrication costs and improve overall longevity. This aim can be achieved by using protonic ceramic fuel cells (PCFCs) due to their higher electrolyte conductivity at these temperatures than traditional ceramic oxide-ion conducting membranes. This thesis deals with the state of the art Ni-BaZr0.85Y0.15O3-δ cermet anodes for PCFCs. The study of PCFCs is in its initial stage and currently only a few methods have been developed to prepare suitable anodes via solid state mechanical mixing of the relevant oxides or by combustion routes using nitrate precursors. This thesis aims to highlight the disadvantages of these traditional methods of anode preparation and to, instead, offer a novel, efficient and low cost nitrate free combustion route to prepare Ni-BaZr0.85Y0.15O3-δ cermet anodes for PCFCs. A wide range of techniques mainly X-ray diffraction (XRD), scanning electron microscopy (SEM), environmental scanning electron microscopy, (ESEM) and electrochemical impedance spectroscopy (EIS) were employed in the cermet anode study. The work also offers a fundamental examination of the effect of porosity, redox cycling behaviour, involvement of proton conducting oxide phase in PCFC cermet anodes and finally progresses to study the electrochemical performance of a state of the art anode supported PCFC. The polarisation behaviour of anodes has been assessed as a function of temperature (T), water vapour (pH2O), hydrogen partial pressures (pH2) and phase purity for electrodes of comparable microstructure. The impedance spectra generally show two arcs at high frequency R2 and low frequency R3 at 600 °C, which correspond to the electrode polarisation resistance. Work shows that the R2 and R3 terms correspond to proton transport and dissociative H2 adsorption on electrode surface, respectively. The polarization resistance of the cermet anode (Rp) was shown to be significantly affected by porosity, with the PCFC cermet anode with the lowest porosity exhibiting the lowest Rp under standard operating conditions. This result highlights that porogens are not required for peak performance in PCFC anodes, a result contrary to that of their oxide-ion conducting anode counterparts. In-situ redox cycling studies demonstrate that polarisation behaviour was drastically impaired by redox cycling. In-situ measurements using an environmental scanning electron microscopy (ESEM) reveal that degradation proceeds due to volume expansion of the Ni-phase during the re-oxidation stage of redox cycling.The anode supported thin BCZY44 based protonic ceramic fuel cell, formed using a peak performing Ni-BaZr0.85Y0.15O3-δ cermet anode with no porogen, shows promising results in fuel cell testing conditions at intermediate temperatures with good durability and an overall performance that exceeds current literature data.

Desenvolvimento de um cerâmico Al2O3/TI(C,N) para uso em maquinação

O principal objetivo deste trabalho é preparar um cermeto do tipo Al2O3/Ti(C,N) com propriedades mecânicas adequadas à sua utilização na maquinação de materiais do tipo DIN ISO 513:K01-K10 e ISO H01-H10. De forma a incrementar a sinterabilidade do cermeto investigou-se o efeito da adição de dopantes metálicos, nomeadamente alumínio metálico (Al) e hidreto de titânio (TiH2) e o efeito da substituição da moagem convencional por moagem de alta energia. As variáveis das etapas principais de processamento, i.e., da moagem, prensagem e sinterização, foram selecionadas com trabalho realizado quer na Universidade de Aveiro quer na empresa Palbit. Foram preparadas três composições do cermeto Al2O3/Ti(C,N) com adições de 5%TiH2, 1%Al e 5%TiH21%Al através da moagem de alta energia. Os parâmetros de moagem, i.e. a velocidade de rotação, o rácio bolas/pó e o tempo de moagem foram otimizados para os seguintes valores: 350 rpm, 10:1 e 5 h, respetivamente. A utilização da moagem de alta energia permitiu uma redução do tamanho de partícula dos pós até aproximadamente 100 nm e a obtenção de uma boa uniformidade da distribuição das fases (Al2O3+Ti(C,N)). A etapa de conformação foi efetuada por prensagem uniaxial seguida de prensagem isostática. A avaliação da reatividade dos cermetos através de dilatometria em atmosfera de vácuo revelou que a densificação é maioritariamente realizada em estado sólido. A adição de apenas 1%Al é a menos efetiva para a densificação. Os cermetos foram sinterizados através de sinterização convencional em forno de vazio a 1650ºC e prensagem a quente (1650ºC com uma pressão uniaxial de 25 MPa). Os valores de densificação obtidos, aproximadamente 80% e 100%, respetivamente, indicam que a aplicação de pressão durante a sinterização é efetiva para atingir densificações elevadas nos compactos, compatíveis com as suas aplicações tecnológicas. As propriedades mecânicas de dureza e de tenacidade avaliadas nos três cermetos apresentaram valores aproximados de 1800-1900 HV50 para a dureza e entre 5.4 e 7.7 MPa.m1/2 para a tenacidade à fratura.