PMMA-co-EHA cements for osteoprotheses

The main purpose of this thesis was to produce new formulations of PMMA-co- EHA and study its feasibility as being an alternative to traditional PMMA bone cements. Thus, were originally produced several co-polymers of PMMA-co-EHA and its mechanical properties and in vitro behaviour were evaluated. The copolymers were obtained by radical polymerization and several formulations were produced by partial replacement of MMA (up to about 50%) for EHA. Overall, the results suggest that the partial replacement of MMA by EHA decreased the modulus of the materials and, consequently, increased its flexibility. Then, PMMA commercial beads were added to PMMA-co-EHA formulations (to get bone cement) and the general properties of the resulting bone cements were evaluated. In general, the results revealed that the partial replacement of MMA by EHA led to beneficial changes in curing parameters (there was a reduction of the peak temperature and an increase of curing/setting time), in the in vitro behaviour (the water capacity increased) and in the mechanical properties (the bending strength increased) of new cements. The in vitro cellular response of new formulations of PMMA-co-EHA was compared with that of traditional PMMA bone cement. To this end, we tested the cell adhesion and proliferation of osteoblast-like MG63 cells and human cells from bone marrow. The results revealed that both types of cells were able to attach and proliferate in both formulations. The only exception was observed for the formulation prepared with the highest percentage of EHA, where a few cells that adhere failed to proliferate. Moreover, it was found that increasing the amount of EHA in cement led to an increasing inhibition of cell growth, especially during the first week of culture. This was related to increased water uptake capacity by the new formulations and consequent release of some of its toxic components. Finally, PMMA commercial beads were partially replaced by HA particles and the influence of this substitution on the curing parameters, the mechanical properties and in vitro behaviour of the resulting composites was also evaluated. Incorporation of HA into the bone cements induced a number of significant changes in its final properties: 1) decrease the peak temperature; 2) increase of curing time, 3) increasing the value of elastic modulus accompanied by decrease of the strength/tension. This last finding was related to poor interfacial adhesion between the various components of the bone cements and a heterogeneous distribution (possible agglomeration) of HA particles.

Alternative techniques for Raman amplification in telecommunications

O presente trabalho centra-se no estudo dos amplificadores de Raman em fibra ótica e suas aplicações em sistemas modernos de comunicações óticas. Abordaram-se tópicos específicos como a simulação espacial do amplificador de Raman, a equalização e alargamento do ganho, o uso de abordagens híbridas de amplificação através da associação de amplificadores de Raman em fibra ótica com amplificadores de fibra dopada com Érbio (EDFA) e os efeitos transitórios no ganho dos amplificadores. As actividades realizadas basearam-se em modelos teóricos, sendo os resultados validados experimentalmente. De entre as contribuições mais importantes desta tese, destaca-se (i) o desenvolvimento de um simulador eficiente para amplificadores de Raman que suporta arquitecturas de bombeamento contraprogantes e bidirecionais num contexto com multiplexagem no comprimento de onda (WDM); (ii) a implementação de um algoritmo de alocação de sinais de bombeamento usando a combinação do algoritmo genético com o método de Nelder- Mead; (iii) a apreciação de soluções de amplificação híbridas por associação dos amplificadores de Raman com EDFA em cenários de redes óticas passivas, nomeadamente WDM/TDM-PON com extensão a região espectral C+L; e (iv) a avaliação e caracterização de fenómenos transitórios em amplificadores para tráfego em rajadas/pacotes óticos e consequente desenvolvimento de soluções de mitigação baseadas em técnicas de clamping ótico.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Acrylic bone cements modified with bioactive and biodegradable fillers

O cimento ósseo acrílico é o único material utilizado para a fixação de próteses em cirurgias ortopédicas, surgindo como uma alternativa às técnicas não cimentadas. Cerca de um milhão de pacientes são anualmente tratados para a substituição total da articulação do quadril e do joelho. Com a maior expectativa de vida da população e o aumento do número de cirurgias realizadas por ano espera-se que o uso do cimento ósseo aumente substancialmente. A fraca ligação do cimento ao osso é um problema comum que pode causar perda asséptica da prótese. Assim, torna-se necessário investir no desenvolvimento de cimentos ósseos alternativos que permitam promover maior estabilidade e melhor desempenho do implante. O principal objetivo desta tese foi desenvolver um cimento ósseo bioativo, capaz de ligar-se ao osso, com propriedades melhoradas relativamente aos sistemas convencionais. A preparação dos materiais foi realizada por dois processos diferentes, a polimerização por via térmica e a polimerização por via química. Inicialmente, utilizando o processo térmico, foram desenvolvidos compósitos de PMMA-co-EHA reforçados com vidro de sílica (CSi) e vidro de boro (CB) e comparados em termos do seu comportamento in vitro em meio acelular e celular. A formação de precipitados de fosfato de cálcio foi observada sobre a superfície de todos os compósitos indicando que estes materiais são potencialmente bioativos. Em relação à avaliação biológica o CSi demonstrou um efeito indutor da proliferação das células. As células apresentaram uma morfologia normal e alta taxa de crescimento quando comparadas com o padrão de cultura. Por outro lado ocorreu inibição da proliferação celular para o CB provavelmente devido à sua elevada taxa de degradação, levando a uma elevada concentraçao de iões de B e de Mg no meio de cultura. O efeito do vidro nos cimentos curados por via química, incorporando um activador de baixa toxicidade, também foi avaliado. Os resultados sugerem que as novas formulações podem diminuir o efeito exotérmico na cura do cimento e melhorar as propriedades mecânicas (flexão e compressão). Outro estudo conduzido neste trabalho explorou a possibilidade de incorporar ibuprofeno (fármaco anti-inflamatório) no cimento, dando origem a um material capaz de ser simultaneamente, bioativo e promotor da libertação controlada de fármacos. Neste contexto foi evidenciado que o desempenho do cimento desenvolvido pode contribuir para minimizar o processo inflamatório associado a uma cirurgia ortopédica. Finalmente, a fase sólida do cimento ósseo bioativo foi modificada por diferentes polímeros biodegradáveis. A adição deste enchimento deu origem a um cimento parcialmente biodegradável que pode permitir a formação de poros e o crescimento ósseo para o interior do cimento, resultando numa melhor fixação da prótese.

Beyond the artefact and techno-centricity: towards process-centric understanding of architecture - alternative facilitation strategies and proposals

The artefact and techno-centricity of the research into the architecture process needs to be counterbalanced by other approaches. An increasing amount of information is collected and used in the process, resulting in challenges related to information and knowledge management, as this research evidences through interviews with practicing architects. However, emerging technologies are expected to resolve many of the traditional challenges, opening up new avenues for research. This research suggests that among them novel techniques addressing how architects interact with project information, especially that indirectly related to the artefacts, and tools which better address the social nature of work, notably communication between participants, become a higher priority. In the fields associated with the Human Computer Interaction generic solutions still frequently prevail, whereas it appears that specific alternative approaches would be particularly in demand for the dynamic and context dependent design process. This research identifies an opportunity for a process-centric and integrative approach for architectural practice and proposes an information management and communication software application, developed for the needs discovered in close collaboration with architects. Departing from the architects’ challenges, an information management software application, Mneme, was designed and developed until a working prototype. It proposes the use of visualizations as an interface to provide an overview of the process, facilitate project information retrieval and access, and visualize relationships between the pieces of information. Challenges with communication about visual content, such as images and 3D files, led to a development of a communication feature allowing discussions attached to any file format and searchable from a database. Based on the architects testing the prototype and literature recognizing the subjective side of usability, this thesis argues that visualizations, even 3D visualizations, present potential as an interface for information management in the architecture process. The architects confirmed that Mneme allowed them to have a better project overview, to easier locate heterogeneous content, and provided context for the project information. Communication feature in Mneme was seen to offer a lot of potential in design projects where diverse file formats are typically used. Through empirical understanding of the challenges in the architecture process, and through testing the resulting software proposal, this thesis suggests promising directions for future research into the architecture and design process.

Analysis, modeling, design and optimization of future communications systems: from theory to practice

Esta tese descreve uma framework de trabalho assente no paradigma multi-camada para analisar, modelar, projectar e optimizar sistemas de comunicação. Nela se explora uma nova perspectiva acerca da camada física que nasce das relações entre a teoria de informação, estimação, métodos probabilísticos, teoria da comunicação e codificação. Esta framework conduz a métodos de projecto para a próxima geração de sistemas de comunicação de alto débito. Além disso, a tese explora várias técnicas de camada de acesso com base na relação entre atraso e débito para o projeto de redes sem fio tolerantes a atrasos. Alguns resultados fundamentais sobre a interação entre a teoria da informação e teoria da estimação conduzem a propostas de um paradigma alternativo para a análise, projecto e optimização de sistemas de comunicação. Com base em estudos sobre a relação entre a informação recíproca e MMSE, a abordagem descrita na tese permite ultrapassar, de forma inovadora, as dificuldades inerentes à optimização das taxas de transmissão de informação confiáveis em sistemas de comunicação, e permite a exploração da atribuição óptima de potência e estruturas óptimas de pre-codificação para diferentes modelos de canal: com fios, sem fios e ópticos. A tese aborda também o problema do atraso, numa tentativa de responder a questões levantadas pela enorme procura de débitos elevados em sistemas de comunicação. Isso é feito através da proposta de novos modelos para sistemas com codificação de rede (network coding) em camadas acima da sua camada física. Em particular, aborda-se a utilização de sistemas de codificação em rede para canais que variam no tempo e são sensíveis a atrasos. Isso foi demonstrado através da proposta de um novo modelo e esquema adaptativo, cujos algoritmos foram aplicados a sistemas sem fios com desvanecimento (fading) complexo, de que são exemplos os sistemas de comunicação via satélite. A tese aborda ainda o uso de sistemas de codificação de rede em cenários de transferência (handover) exigentes. Isso é feito através da proposta de novos modelos de transmissão WiFi IEEE 801.11 MAC, que são comparados com codificação de rede, e que se demonstram possibilitar transferência sem descontinuidades. Pode assim dizer-se que esta tese, através de trabalho de análise e de propostas suportadas por simulações, defende que na concepção de sistemas de comunicação se devem considerar estratégias de transmissão e codificação que sejam não só próximas da capacidade dos canais, mas também tolerantes a atrasos, e que tais estratégias têm de ser concebidas tendo em vista características do canal e a camada física.

Valorization of solid wastes from cellulose and paper industry

This thesis reports in detail studies of industrial solid wastes valorization as alternative raw materials. All tested wastes are classified as non-hazardous and are generated in the pulp and paper process, including primary sludge, dregs, grits, lime mud and bottom ash (this generated in a process that occurs in parallel to the production of cellulose, whose aim is the production of energy to supply the plant through the combustion of forest biomass in fluidized bed). A detailed general characterization was performed at each waste and according to their characteristics, they were selected some applications in materials with potential use, specifically in Fibercement, Bituminous Mixture for regularization layer and industrial mortars (rendering mortars and cementitious-adhesive). After decided to application each waste was specifically tested to proceed the setting up of formulations containing different content of waste in replacement of the raw conventional material. As an isolated case, the bottom ash was tested not only as an alternative raw material for construction materials, but also it was tested for its use in fluidized bed in which the waste is generated as raw material. Both dregs and bottom ash had undergone special treatment to make possible to obtain a better quality of waste in order do not compromise the final product characteristics and process. The dregs were tested in bituminous mixtures as received and also washed (on the laboratory scale to remove soluble salts) and bottom ash were washed and screened in industrial scale (for removal of soluble salts, especially chlorides and coarse fraction particles elimination - particles larger than 1 mm size). The remaining residues form used in such as received avoiding additional costs. The results indicated potential and some limitations for each application to the use of these wastes as alternative raw material, but in some cases, the benefits in relation to valorization overlap with its limitations in both aspects, environmental and economic.