Network virtualisation from an operator perspective

Network virtualisation is seen as a promising approach to overcome the so-called “Internet impasse” and bring innovation back into the Internet, by allowing easier migration towards novel networking approaches as well as the coexistence of complementary network architectures on a shared infrastructure in a commercial context. Recently, the interest from the operators and mainstream industry in network virtualisation has grown quite significantly, as the potential benefits of virtualisation became clearer, both from an economical and an operational point of view. In the beginning, the concept has been mainly a research topic and has been materialized in small-scale testbeds and research network environments. This PhD Thesis aims to provide the network operator with a set of mechanisms and algorithms capable of managing and controlling virtual networks. To this end, we propose a framework that aims to allocate, monitor and control virtual resources in a centralized and efficient manner. In order to analyse the performance of the framework, we performed the implementation and evaluation on a small-scale testbed. To enable the operator to make an efficient allocation, in real-time, and on-demand, of virtual networks onto the substrate network, it is proposed a heuristic algorithm to perform the virtual network mapping. For the network operator to obtain the highest profit of the physical network, it is also proposed a mathematical formulation that aims to maximize the number of allocated virtual networks onto the physical network. Since the power consumption of the physical network is very significant in the operating costs, it is important to make the allocation of virtual networks in fewer physical resources and onto physical resources already active. To address this challenge, we propose a mathematical formulation that aims to minimize the energy consumption of the physical network without affecting the efficiency of the allocation of virtual networks. To minimize fragmentation of the physical network while increasing the revenue of the operator, it is extended the initial formulation to contemplate the re-optimization of previously mapped virtual networks, so that the operator has a better use of its physical infrastructure. It is also necessary to address the migration of virtual networks, either for reasons of load balancing or for reasons of imminent failure of physical resources, without affecting the proper functioning of the virtual network. To this end, we propose a method based on cloning techniques to perform the migration of virtual networks across the physical infrastructure, transparently, and without affecting the virtual network. In order to assess the resilience of virtual networks to physical network failures, while obtaining the optimal solution for the migration of virtual networks in case of imminent failure of physical resources, the mathematical formulation is extended to minimize the number of nodes migrated and the relocation of virtual links. In comparison with our optimization proposals, we found out that existing heuristics for mapping virtual networks have a poor performance. We also found that it is possible to minimize the energy consumption without penalizing the efficient allocation. By applying the re-optimization on the virtual networks, it has been shown that it is possible to obtain more free resources as well as having the physical resources better balanced. Finally, it was shown that virtual networks are quite resilient to failures on the physical network.

Avaliação do perfil de cuidado de enfermagem geriátrico em hospitais de Portugal

A transição demográfica e epidemiológica da população portuguesa tem e terá um enorme impacto na utilização dos recursos de saúde. Atualmente, as pessoas idosas representam um dos grupos etários com taxas de internamento hospitalar mais significativos. Contudo, os dados sobre a hospitalização destas pessoas têm demonstrado resultados de saúde negativos, nomeadamente, o declínio funcional e cognitivo e o risco elevado de eventos adversos. Os/as enfermeiros/as têm um papel crucial na mudança desta realidade. Deste modo, a associação entre o contexto no qual decorre o cuidado de enfermagem geriátrica e os resultados deste cuidado relativos a/os utentes, enfermeiros/as e organizações têm sido proficuamente documentados. Algumas estratégias para promover a qualidade do cuidado geriátrico e a segurança das pessoas idosas hospitalizadas consistem em avaliar e (re)criar o ambiente de trabalho geriátrico dos/as enfermeiros/as (AGTE) e capacitar e treinar estes/as profissionais no cuidado à pessoa idosa. Embora, internacionalmente, os dados demonstrem a associação entre as características de hospitais e/ou enfermeiros/as e o AGTE, não existem estudos em Portugal nesta área, bem como sobre o conhecimento e as atitudes destes profissionais no contexto hospitalar. Por conseguinte, este estudo teve como objetivos: 1) traduzir, adaptar culturalmente e validar as escalas que compõem o questionário Geriatric Institucional Assessment Proflie (GIAP) para a população portuguesa; 2) analisar o AGTE (fatores intrínsecos e extrínsecos) que apoiam ou dificultam a adoção das melhores práticas geriátricas em hospitais portugueses; 3) analisar as atitudes e conhecimento de enfermeiros/as acerca de quatro síndromes geriátricas (úlceras de pressão, distúrbio do sono, contenção física e incontinência), destacando as boas práticas e os problemas encontrados nos hospitais portugueses; 4) analisar a relação entre as variáveis demográficas, profissionais e as características dos hospitais e as escalas que compõem o GIAP – versão portuguesa; 5) conhecer as perceções de enfermeiros/as acerca do cuidado às pessoas idosas hospitalizadas e dos obstáculos enfrentados para desenvolver um cuidado de boa qualidade; e 6) analisar a relação entre a perceção de enfermeiros/as sobre o AGTE e o conhecimento e atitudes geriátricas destes profissionais em função da região e unidade de internamento. Este estudo foi desenvolvido com base num método quantitativo do tipo exploratório-descritivo, transversal, prospetivo e correlacional. A amostra foi constituída por 1.068 enfermeiros/as de cinco hospitais da região norte e centro do país. A recolha de dados foi desenvolvida através de autopreenchimento do GIAP – versão portuguesa. De entre os principais resultados destacam-se: 1) a obtenção de um instrumento válido e fiável para avaliar o AGTE e conhecimentos e atitudes geriátricas; 2) a perceção de enfermeiros/as sobre o cuidado às pessoas idosas como sendo predominantemente negativa; 3) a perceção de enfermeiros/as sobre o apoio insuficiente dos líderes hospitalares para promover um AGTE favorável; 4) o cuidado a pessoas idosas com comportamentos inadequados e o uso de recursos geriátricos como os principais fatores que influenciam a eficácia e a qualidade do cuidado geriátrico; 5) a lacuna de conhecimento e atitudes negativas de enfermeiros/as acerca das quatro síndromes geriátricas; 6) a conceptualização de um modelo sobre a associação das características de enfermeiros/as, dos hospitais do estudo e das perceções destes/as profissionais sobre o cuidado geriátrico com o AGTE e o conhecimento e atitudes geriátricos; 7) a falta de apoio familiar, a descontinuidade e a escassez de tempo para o cuidado como principais obstáculos no cuidado à pessoa idosa hospitalizada; e 8) o perfil de cuidado geriátrico nos hospitais da região norte e centro de Portugal como tendencialmente homogéneo. Os resultados deste estudo sustentam a necessidade de um maior investimento dos decisores políticos, administradores hospitalares e docentes de Enfermagem na capacitação dos/as enfermeiros/as para o cuidado geriátrico e na promoção de um AGTE mais favorável. Também oferece recomendações significativas nos domínios da decisão política, da gestão institucional e da prática profissional que devem ser alvo de uma discussão alargada entre os vários agentes com responsabilidade nestes domínios. Espera-se que este estudo possa contribuir para a promoção de um contexto favorável ao desenvolvimento de um cuidado de enfermagem geriátrica de boa qualidade às pessoas hospitalizadas.

Pregnancy and newborns disorders followed by urine metabolomics

Chapter 1 introduces the scope of the work by identifying the clinically relevant prenatal disorders and presently available diagnostic methods. The methodology followed in this work is presented, along with a brief account of the principles of the analytical and statistical tools employed. A thorough description of the state of the art of metabolomics in prenatal research concludes the chapter, highlighting the merit of this novel strategy to identify robust disease biomarkers. The scarce use of maternal and newborn urine in previous reports enlightens the relevance of this work. Chapter 2 presents a description of all the experimental details involved in the work performed, comprising sampling, sample collection and preparation issues, data acquisition protocols and data analysis procedures. The proton Nuclear Magnetic Resonance (NMR) characterization of maternal urine composition in healthy pregnancies is presented in Chapter 3. The urinary metabolic profile characteristic of each pregnancy trimester was defined and a 21-metabolite signature found descriptive of the metabolic adaptations occurring throughout pregnancy. 8 metabolites were found, for the first time to our knowledge, to vary in connection to pregnancy, while known metabolic effects were confirmed. This chapter includes a study of the effects of non-fasting (used in this work) as a possible confounder. Chapter 4 describes the metabolomic study of 2nd trimester maternal urine for the diagnosis of fetal disorders and prediction of later-developing complications. This was achieved by applying a novel variable selection method developed in the context of this work. It was found that fetal malformations (FM) (and, specifically those of the central nervous system, CNS) and chromosomal disorders (CD) (and, specifically, trisomy 21, T21) are accompanied by changes in energy, amino acids, lipids and nucleotides metabolic pathways, with CD causing a further deregulation in sugars metabolism, urea cycle and/or creatinine biosynthesis. Multivariate analysis models´ validation revealed classification rates (CR) of 84% for FM (87%, CNS) and 85% for CD (94%, T21). For later-diagnosed preterm delivery (PTD), preeclampsia (PE) and intrauterine growth restriction (IUGR), it is found that urinary NMR profiles have early predictive value, with CRs ranging from 84% for PTD (11-20 gestational weeks, g.w., prior to diagnosis), 94% for PE (18-24 g.w. pre-diagnosis) and 94% for IUGR (2-22 g.w. pre-diagnosis). This chapter includes results obtained for an ultraperformance liquid chromatography-mass spectrometry (UPLC-MS) study of pre-PTD samples and correlation with NMR data. One possible marker was detected, although its identification was not possible. Chapter 5 relates to the NMR metabolomic study of gestational diabetes mellitus (GDM), establishing a potentially predictive urinary metabolic profile for GDM, 2-21 g.w. prior to diagnosis (CR 83%). Furthermore, the NMR spectrum was shown to carry information on individual phenotypes, able to predict future insulin treatment requirement (CR 94%). Chapter 6 describes results that demonstrate the impact of delivery mode (CR 88%) and gender (CR 76%) on newborn urinary profile. It was also found that newborn prematurity, respiratory depression, large for gestational age growth and malformations induce relevant metabolic perturbations (CR 82-92%), as well as maternal conditions, namely GDM (CR 82%) and maternal psychiatric disorders (CR 91%). Finally, the main conclusions of this thesis are presented in Chapter 7, highlighting the value of maternal or newborn urine metabolomics for pregnancy monitoring and disease prediction, towards the development of new early and non-invasive diagnostic methods.

Promoção da acessibilidade em televisão interativa (iTV) : proposta de um serviço adaptado a utilizadores com défice visual

As infraestruturas de televisão interativa atualmente existentes possibilitam a integração de uma grande variedade de recursos e serviços, possibilitando aos utilizadores novas experiências de interação e participação. Para a maioria dos telespetadores, o uso de serviços interativos não acarreta grandes dificuldades; no entanto, para públicos com necessidades especiais, por exemplo para pessoas com défice visual, essa tarefa torna-se complexa, dificultando, ou mesmo impedindo, que estes utilizadores possam beneficiar deste tipo de serviços. Portugal não é uma exceção neste contexto, existindo um número significativo de utilizadores com défice visual (UDV) que não beneficiam totalmente das potencialidades do paradigma televisivo atual. Neste âmbito, o projeto de investigação que suporta esta tese explora a problemática do Design Universal aplicado à Televisão Interativa (iTV) e tem como objetivos a conceptualização, prototipagem e validação de um serviço de iTV adaptado especificamente a UDV, visando promover a sua inclusão digital. Para cumprir estes objetivos, a investigação dividiu-se em três etapas distintas. Na primeira etapa, a partir da Teoria Fundamentada nos Dados, foram identificadas as dificuldades e necessidades dos UDV enquanto consumidores de conteúdos televisivos e serviços de audiodescrição; foi selecionada a plataforma tecnológica mais adequada para o suporte do serviço prototipado; e foi definido um conjunto de princípios orientadores de design (POD’s) de interfaces de televisão interativa específico para este público-alvo. Inicialmente foram efetuadas duas entrevistas a 20 participantes com défice visual, para determinar as suas dificuldades e necessidades enquanto consumidores de conteúdos televisivos e serviços de audiodescrição. De seguida, foi realizada uma entrevista a um perito responsável pelo processo de transição para a TDT em Portugal (inicialmente considerou-se que a TDT seria uma plataforma promissora e poderia suportar o protótipo) e efetuada a revisão da literatura sobre POD’s para o desenvolvimento de interfaces para serviços iTV dirigidos a pessoas com défice visual. A partir dos resultados obtidos nesta etapa foi possível definir os requisitos funcionais e técnicos do sistema, bem como os seus PODs, tanto ao nível da componente gráfica, como de interação. Na segunda etapa foi concetualizado e desenvolvido o protótipo iTV adaptado a UDV ‘meo ad+’, com recurso à plataforma tecnológica IPTV da Portugal Telecom, seguindo os requisitos e os princípios de design definidos. Relativamente à terceira etapa, esta contemplou a avaliação do serviço prototipado, por parte de um grupo de participantes com défice visual. Esta fase do trabalho foi conduzida através do método de Estudo Avaliativo, possibilitando, através de testes de usabilidade e acessibilidade, complementados com entrevistas, compreender se o serviço prototipado ia efetivamente ao encontro das necessidades deste tipo de utilizadores, tendo-se observado que os participantes que estiveram envolvidos nos testes ao protótipo mostraram-se satisfeitos com as funcionalidades oferecidas pelo sistema, bem como com o design da sua interface.

Interactions of cetaceans with Spanish and Portuguese fisheries in Atlantic waters : costs, benefits and implications for management

With the aim to provide new insights into operational cetacean-fishery interactions in Atlantic waters, this thesis assesses interactions of cetaceans with Spanish and Portuguese fishing vessels operating in Iberian and South West Atlantic waters. Different opportunistic research methodologies were applied, including an interview survey with fishers (mainly skippers) and onboard observations by fisheries observers and skippers, to describe different types of interactions and to identify potential hotspots for cetacean-fishery interactions and the cetacean species most involved, and to quantify the extent and the consequences of these interactions in terms of benefits and costs for cetaceans and fisheries. In addition, the suitability of different mitigation strategies was evaluated and discussed. The results of this work indicate that cetaceans interact frequently with Spanish and Portuguese fishing vessels, sometimes in a beneficial way (e.g. cetaceans indicate fish schools in purse seine fisheries), but mostly with negative consequences (depredation on catch, gear damage and cetacean bycatch). Significant economic loss and high bycatch rates are, however, only reported for certain fisheries and associated with particular cetacean species. In Galician fisheries, substantial economic loss was reported as a result of bottlenose dolphins damaging artisanal coastal gillnets, while high catch loss may arise from common dolphins scattering fish in purse seine fisheries. High cetacean bycatch mortality arises in trawl fisheries, mainly of common dolphin and particularly during trawling in water depths below 350 m, and in coastal set gillnet fisheries (mainly common and bottlenose dolphins). In large-scale bottom-set longline fisheries in South West Atlantic waters, sperm whales may significantly reduce catch rates through depredation on catch. The high diversity of cetacean-fishery interactions observed in the study area indicates that case-specific management strategies are needed to reduce negative impacts on fisheries and cetaceans. Acoustic deterrent devices (pingers) may be used to prevent small cetaceans from approaching and getting entangled in purse seines and set gillnets, although possible problems include cetacean habituation to the pinger sounds, as well as negative side effects on non-target cetaceans (habitat exclusion) and fisheries target species (reduced catch rates). For sardine and horse mackerel, target species of Iberian Atlantic fisheries, no aversive reaction to pinger sounds was detected during tank experiments conducted in the scope of this thesis. Bycatch in trawls may be reduced by the implementation of time/area restrictions of fishing activity. In addition, the avoidance of fishing areas with high cetacean abundance combined with the minimization of fishery-specific sound cues that possibly attract cetaceans, may also help to decrease interactions. In large-scale bottom-set longline fisheries, cetacean depredation on catch may be reduced by covering hooked fish with net sleeves ("umbrellas") provided that catch rates are not negatively affected by this gear modification. Trap fishing, as an alternative fishing method to bottom-set gillnetting and longlining, also has the potential to reduce cetacean bycatch and depredation, given that fish catch rates are similar to the rates obtained by bottom-set gillnets and longlines, whereas cetacean by-catch is unlikely. Economic incentives, such as the eco-certification of dolphin-safe fishing methods, should be promoted in order to create an additional source of income for fishers negatively affected by interactions with cetaceans, which, in turn, may also increase fishers’ willingness to accept and adopt mitigation measures. Although the opportunistic sampling methods applied in this work have certain restrictions concerning their reliability and precision, the results are consistent with previous studies in the same area. Moreover, they allow for the active participation of fishers that can provide important complementary ecological and technical knowledge required for cetacean management and conservation.

Multilayered micro/nanocrystalline CVD diamond coatings for biotribology

In the present work multilayered micro/nanocrystalline (MCD/NCD) diamond coatings were developed by Hot Filament Chemical Vapour Deposition (HFCVD). The aim was to minimize the surface roughness with a top NCD layer, to maximize adhesion onto the Si3N4 ceramic substrates with a starting MCD coating and to improve the mechanical resistance by the presence of MCD/NCD interfaces in these composite coatings. This set of features assures high wear resistance and low friction coefficients which, combined to diamond biocompatibility, set this material as ideal for biotribological applications. The deposition parameters of MCD were optimized using the Taguchi method, and two varieties of NCD were used: NCD-1, grown in a methane rich gas phase, and NCD-2 where a third gas, Argon, was added to the gas mixture. The best combination of surface pre-treatments in the Si3N4 substrates is obtained by polishing the substrates with a 15 μm diamond slurry, further dry etching with CF4 plasma for 10 minutes and final ultrasonic seeding in a diamond powder suspension in ethanol for 1 hour. The interfaces of the multilayered CVD diamond films were characterized with high detail using HRTEM, STEM-EDX and EELS. The results show that at the transition from MCD to NCD a thin precursor graphitic film is formed. On the contrary, the transition of the NCD to MCD grade is free of carbon structures other than diamond, as a result of the richer atomic hydrogen content and of the higher substrate temperature for MCD deposition. At those transitions, WC nanoparticles were found due to contamination from the filament, being also present at the first interface of the MCD layer with the silicon nitride substrate. In order to study the adhesion and mechanical resistance of the diamond coatings, indentation and particle jet blasting tests were conducted, as well as tribological experiments with homologous pairs. Indentation tests proved the superior behaviour of the multilayered coatings that attained a load of 800 N without delamination, when compared to the mono and bilayered ones. The multilayered diamond coatings also reveal the best solid particle erosion resistance, due to the MCD/NCD interfaces that act as crack deflectors. These results were confirmed by an analytical model on the stress field distribution based on the von Mises criterion. Regarding the tribological testing under dry sliding, multilayered coatings also exhibit the highest critical load values (200N for Multilayers with NCD-2). Low friction coefficient values in the range μ=0.02- 0.09 and wear coefficient values in the order of ~10-7 mm3 N-1 m-1 were obtained for the ball and flat specimens indicating a mild wear regime. Under lubrication with physiological fluids (HBSS e FBS), lower wear coefficient values ~10-9-10-8 mm3 N-1 m-1) were achieved, governed by the initial surface roughness and the effective contact pressure.

Quantificação de mercúrio em águas de consumo: validação do método na Luságua

Para o ser humano, a água sempre foi um recurso essencial ao longo da sua evolução. Hoje em dia, com todo o avanço tecnológico, a água é um bem muito vulnerável às diversas atividades antropogénicas. Entre os muitos contaminantes que podem afetar a qualidade da água para consumo humano, os metais causam grande preocupação devido à sua elevada toxicidade. O mercúrio é um dos contaminantes que deve ser devidamente controlado devido ao seu elevado grau de toxicidade. Este Estágio foi realizado no Laboratório Luságua e o seu principal objetivo foi avaliar se era possível baixar o limite de quantificação da técnica existente na empresa para quantificar o mercúrio em águas de consumo e validar o método através do cálculo de vários parâmetros de controlo de qualidade. Foi ainda feita a comparação entre a técnica de quantificação de mercúrio existente na Luságua (CV-AAS) e a existente na Universidade de Aveiro (CVAFS) para avaliar se havia uma mais-valia para a Luságua se adquirisse um novo equipamento para analisar o mercúrio em águas. Os parâmetros de validação avaliados nos dois métodos derem resultados semelhantes, não identificando a necessidade atual de substituir o equipamento existente na Luságua, até porque se conseguiu baixar o limite de quantificação, atingindo assim o objetivo estabelecido no início para este Estágio.

The impact of biofuels for road traffic on air quality : a modelling approach

The selection of the energy source to power the transport sector is one of the main current concerns, not only relative with the energy paradigm but also due to the strong influence of road traffic in urban areas, which highly affects human exposure to air pollutants and human health and quality of life. Due to current important technical limitations of advanced energy sources for transportation purposes, biofuels are seen as an alternative way to power the world’s motor vehicles in a near-future, helping to reduce GHG emissions while at the same time stimulating rural development. Motivated by European strategies, Portugal, has been betting on biofuels to meet the Directive 2009/28/CE goals for road transports using biofuels, especially biodiesel, even though, there is unawareness regarding its impacts on air quality. In this sense, this work intends to clarify this issue by trying to answer the following question: can biodiesel use contribute to a better air quality over Portugal, particularly over urban areas? The first step of this work consisted on the characterization of the national biodiesel supply chain, which allows verifying that the biodiesel chain has problems of sustainability as it depends on raw materials importation, therefore not contributing to reduce the external energy dependence. Next, atmospheric pollutant emissions and air quality impacts associated to the biodiesel use on road transports were assessed, over Portugal and in particular over the Porto urban area, making use of the WRF-EURAD mesoscale numerical modelling system. For that, two emission scenarios were defined: a reference situation without biodiesel use and a scenario reflecting the use of a B20 fuel. Through the comparison of both scenarios, it was verified that the use of B20 fuels helps in controlling air pollution, promoting reductions on PM10, PM2.5, CO and total NMVOC concentrations. It was also verified that NO2 concentrations decrease over the mainland Portugal, but increase in the Porto urban area, as well as formaldehyde, acetaldehyde and acrolein emissions in the both case studies. However, the use of pure diesel is more injurious for human health due to its dominant VOC which have higher chronic hazard quotients and hazard indices when compared to B20.

Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Turismo acessível : recurso de coping para gerir o stress na incapacidade

As sociedades contemporâneas testemunham os efeitos negativos do stress sobre a saúde, existindo evidências empíricas do relacionamento recíproco entre stress e doença (infeciosas, crónicas, cardiovasculares, cancro) (Iwasaki & Mannell, 2000). Por outro lado, Walden (2007) sublinha que o stress varia de acordo com as circunstâncias de vida e Rode et al. (2012) acrescentam que as pessoas com incapacidade apresentam taxas mais elevadas de problemas de saúde relacionados com o stress do que a população em geral. Neste contexto, surge o lazer como mecanismo de coping, como instrumento restaurador e benéfico para a saúde (Caldwell, 2005; Wijndaele et al., 2007). Assim, considerando o turismo como uma marcante atividade recreacional em tempo de lazer na vida das pessoas, e uma oportunidade de relaxamento e interação social (Richards, et al., 2010), pensou-se na possibilidade do turismo acessível ser um recurso de coping para gerir o stress na incapacidade. É com base na atualidade e pertinência destas reflexões que se estabeleceram duas metas para este trabalho: compreender o relacionamento entre turismo, stress e coping para os indivíduos com incapacidade, e desenvolver bases empíricas para fins terapêuticos e para o desenvolvimento de novos produtos turísticos, numa lógica biopsicossocial (biológica ou física, psicológica e social). Especificamente, pretende-se identificar fontes de stress para as pessoas com incapacidade e as suas respostas de coping, e explicar como o turismo atua nas dimensões biopsicossociais do stress-coping. Para atingir estes objetivos utilizou-se uma metodologia mista, suportada por uma revisão de literatura aprofundada, que consistiu na realização de um estudo qualitativo e outro quantitativo. No primeiro, recorreu-se à técnica de focus groups para cada tipo de incapacidade em análise, motora (N=6), auditiva (N=7) e visual (N=6), e no segundo, procedeu-se à aplicação de inquéritos por questionário a pessoas com incapacidade motora e sensorial (N=306), cujo questionário consistiu na adaptação e ajuste das ECL (Escalas de Coping através do Lazer) ao contexto do Turismo Acessível. Os resultados indicam que a principal fonte de stress dos indivíduos com incapacidade é a própria incapacidade em conjugação com a sociedade, demonstrando-se a prevalência de estratégias baseadas na interação social para a resolução de problemas, em detrimento de outras. Por sua vez, apuram-se os benefícios do turismo, cujas mais-valias no âmbito das dimensões biopsicossociais destes indivíduos em particular, são também discutidas. Conclui-se, portanto, que o turismo acessível é um novo formato de stress-coping para a população com incapacidade, suportando o reequilíbrio e harmonização dos seus recursos pessoais e sociais, contribuindo positivamente para a sua saúde e bem-estar global, servindo de base ao desenvolvimento de novos produtos turísticos adequados e direcionados para as necessidades específicas desta população e ao planeamento de intervenções terapêuticas alternativas no contexto da sua reabilitação.

Monitoring and all-optical signal processing techniques for transparent networks

Optical networks are under constant evolution. The growing demand for dynamism require devices that can accommodate different types of traffic. Thus the study of transparent optical networks arises. This approach makes optical networks more "elegant" , due to a more efficient use of network resources. In this thesis, the author proposes devices that intend to form alternative approaches both in the state of art of these same technologies both in the fitting of this technologies in transparent optical networks. Given that full transparency is difficult to achieve with current technology (perhaps with more developed optical computing this is possible), the author proposes techniques with different levels of transparency. On the topic of performance of optical networks, the author proposes two techniques for monitoring chromatic dispersion with different levels of transparency. In Chapter 3 the proposed technique seems to make more sense for long-haul optical transmission links and high transmission rates, not only due to its moderate complexity but also to its potential moderate/high cost. However it is proposed to several modulation formats, particularly those that have a protruding clock component. In Chapter 4 the transparency level was not tested for various modulation formats, however some transparency is achieved by not adding any electrical device after the receiver (other than an analog-digital converter). This allows that this technique can operate at high transmission rates in excess of 100 Gbit / s, if electro-optical asynchronous sampling is used before the optical receiver. Thus a low cost and low bandwidth photo-detector can be used. In chapter 5 is demonstrated a technique for simultaneously monitoring multiple impairments of the optical network by generating novel performance analysis diagrams and by use of artificial neural networks. In chapter 6 the author demonstrates an all-optical technique for controlling the optical state of polarization and an example of how all-optical signal processing can fully cooperate with optical performance monitoring.

Understanding and modelling hydrological and soil erosion processes in burnt forest catchments

Forest fires implications in overland flow and soil erosion have been researched for several years. Therefore, is widely known that fires enhance hydrological and geomorphological activity worldwide as also in Mediterranean areas. Soil burn severity has been widely used to describe the impacts of fire on soils, and has being recognized as a decisive factor controlling post-fire erosion rates. However, there is no unique definition of the term and the relationship between soil burn severity and post-fire hydrological and erosion response has not yet been fully established. Few studies have assessed post-fire erosion over multiple years, and the authors are aware of none which assess runoff. Small amount of studies concerning pre-fire management practices were also found. In the case of soil erosion models, the Revised Universal Soil Loss Equation (RUSLE) and the revised Morgan–Morgan–Finney (MMF) are well-known models, but not much information is available as regards their suitability in predicting post-fire soil erosion in forest soils. The lack of information is even more pronounced as regards post-fire rehabilitation treatments. The aim of the thesis was to perform an extensive research under the post fire hydrologic and erosive response subject. By understanding the effect of burn severity in ecosystems and its implications regarding post fire hydrological and erosive responses worldwide. Test the effect of different pre-fire land management practices (unplowed, downslope plowed and contour plowed) and time-since-fire, in the post fire hydrological and erosive response, between the two most common land uses in Portugal (pine and eucalypt). Assess the performance of two widely-known erosion models (RUSLE and Revised MMF), to predict soil erosion rates during first year following two wildfires of distinctive burn severity. Furthermore, to apply these two models considering different post-fire rehabilitation treatments in an area severely affected by fire. Improve model estimations of post-fire runoff and erosion rates in two different land uses (pine and eucalypt) using the revised MMF. To assess these improvements by comparing estimations and measurements of runoff and erosion, in two recently burned sites, as also with their post fire rehabilitation treatments. Model modifications involved: (1) focusing on intra-annual changes in parameters to incorporate seasonal differences in runoff and erosion; and (2) inclusion of soil water repellency in runoff predictions. Additionally, validate these improvements with the application of the model to other pine and eucalypt sites in Central Portugal. The review and meta-analysis showed that fire occurrence had a significant effect on the hydrological and erosive response. However, this effect was only significantly higher with increasing soil burn severity for inter-rill erosion, and not for runoff. This study furthermore highlighted the incoherencies between existing burn severity classifications, and proposed an unambiguous classification. In the case of the erosion plots with natural rainfall, land use factor affected annual runoff while land management affected both annual runoff and erosion amounts significantly. Time-since-fire had an important effect in erosion amounts among unplowed sites, while for eucalypt sites time affected both annual runoff and erosion amounts. At all studied sites runoff coefficients increase over the four years of monitoring. In the other hand, sediment concentration in the runoff, recorded a decrease during the same period. Reasons for divergence from the classic post-fire recovery model were also explored. Short fire recurrence intervals and forest management practices are viewed as the main reasons for the observed severe and continuing soil degradation. The revised MMF model presented reasonable accuracy in the predictions while the RUSLE clearly overestimated the observed erosion rates. After improvements: the revised model was able to predict first-year post-fire plot-scale runoff and erosion rates for both forest types, these predictions were improved both by the seasonal changes in the model parameters; and by considering the effect of soil water repellency on the runoff, individual seasonal predictions were considered accurate, and the inclusion of the soil water repellency in the model also improved the model at this base. The revised MMF model proved capable of providing a simple set of criteria for management decisions about runoff and erosion mitigation measures in burned areas. The erosion predictions at the validation sites attested both to the robustness of the model and of the calibration parameters, suggesting a potential wider application.

A influência da participação em linha do utilizador na produção das webrádios: um estudo multicaso da Campina FM e da Rádio Comercial

A presente investigação aborda a relação entre a participação em linha do utilizador e a produção de conteúdo na webrádio, tendo como objetivo geral investigar se e como a produção das webrádios é influenciada pela participação em linha dos utilizadores no contexto transmedia. A pesquisa é dividida em duas partes. A primeira é teórica, na qual aborda-se os conceitos fundamentais da investigação e a metodologia adotada para a recolha e análise dos dados. A segunda é prática e se refere às recolhas de dados feitas em duas emissoras (uma brasileira, a Campina FM, e outra portuguesa, a Rádio Comercial) e à apresentação e interpretação desses dados. Em relação ao conteúdo teórico são adotados como conceitos fundamentais: webrádio, radiomorfose, narrativa transmedia, participação em linha do utilizador e produção em webrádio. A metodologia empregue se apresenta no método etnográfico e baseia-se em quatro técnicas de recolhas distintas: observação não-participante, observação participante, inquérito por questionário e inquérito por entrevistas. Tendo por base a análise dos dados recolhidos, as principais conclusões desta tese são: há a potencialização do utilizador nas narrativas transmedia apresentadas, com a rede Facebook sendo o recurso interativo mais importante, mas que, por limites da emissora (sejam conceituais ou técnicos), a participação do utilizador não tem influência direta na produção da webrádio.

Channel modelling for MIMO systems

Systems equipped with multiple antennas at the transmitter and at the receiver, known as MIMO (Multiple Input Multiple Output) systems, offer higher capacities, allowing an efficient exploitation of the available spectrum and/or the employment of more demanding applications. It is well known that the radio channel is characterized by multipath propagation, a phenomenon deemed problematic and whose mitigation has been achieved through techniques such as diversity, beamforming or adaptive antennas. By exploring conveniently the spatial domain MIMO systems turn the characteristics of the multipath channel into an advantage and allow creating multiple parallel and independent virtual channels. However, the achievable benefits are constrained by the propagation channel’s characteristics, which may not always be ideal. This work focuses on the characterization of the MIMO radio channel. It begins with the presentation of the fundamental results from information theory that triggered the interest on these systems, including the discussion of some of their potential benefits and a review of the existing channel models for MIMO systems. The characterization of the MIMO channel developed in this work is based on experimental measurements of the double-directional channel. The measurement system is based on a vector network analyzer and a two-dimensional positioning platform, both controlled by a computer, allowing the measurement of the channel’s frequency response at the locations of a synthetic array. Data is then processed using the SAGE (Space-Alternating Expectation-Maximization) algorithm to obtain the parameters (delay, direction of arrival and complex amplitude) of the channel’s most relevant multipath components. Afterwards, using a clustering algorithm these data are grouped into clusters. Finally, statistical information is extracted allowing the characterization of the channel’s multipath components. The information about the multipath characteristics of the channel, induced by existing scatterers in the propagation scenario, enables the characterization of MIMO channel and thus to evaluate its performance. The method was finally validated using MIMO measurements.

Assessing the effectiveness of chemical treatment with nanomaterials in improving the quality of different industrial effluents

Industrial activities are the major sources of pollution in all environments. Depending on the type of industry, various levels of organic and inorganic pollutants are being continuously discharged into the environment. Although, several kinds of physical, chemical, biological or the combination of methods have been proposed and applied to minimize the impact of industrial effluents, few have proved to be totally effective in terms of removal rates of several contaminants, toxicity reduction or amelioration of physical and chemical properties. Hence, it is imperative to develop new and innovative methodologies for industrial wastewater treatment. In this context nanotechnology arises announcing the offer of new possibilities for the treatment of wastewaters mainly based on the enhanced physical and chemical proprieties of nanomaterials (NMs), which can remarkably increase their adsorption and oxidation potential. Although applications of NMs may bring benefits, their widespread use will also contribute for their introduction into the environment and concerns have been raised about the intentional use of these materials. Further, the same properties that make NMs so appealing can also be responsible for producing ecotoxicological effects. In a first stage, with the objective of selecting NMs for the treatment of organic and inorganic effluents we first assessed the potential toxicity of nanoparticles of nickel oxide (NiO) with two different sizes (100 and 10-20 nm), titanium dioxide (TiO2, < 25 nm) and iron oxide (Fe2O3, ≈ 85x425 nm). The ecotoxicological assessment was performed with a battery of assays using aquatic organisms from different trophic levels. Since TiO2 and Fe2O3 were the NMs that presented lower risks to the aquatic systems, they were selected for the second stage of this work. Thus, the two NMs pre-selected were tested for the treatment of olive mill wastewater (OMW). They were used as catalyst in photodegradation systems (TiO2/UV, Fe2O3/UV, TiO2/H2O2/UV and Fe2O3/H2O2/UV). The treatments with TiO2 or Fe2O3 combined with H2O2 were the most efficient in ameliorating some chemical properties of the effluent. Regarding the toxicity to V. fischeri the highest reduction was recorded for the H2O2/UV system, without NMs. Afterwards a sequential treatment using photocatalytic oxidation with NMs and degradation with white-rot fungi was applied to OMW. This new approach increased the reduction of chemical oxygen demand, phenolic content and ecotoxicity to V. fischeri. However, no reduction in color and aromatic compounds was achieved after 21 days of biological treatment. The photodegradation systems were also applied to treat the kraft pulp mill and mining effluents. For the organic effluent the combination NMs and H2O2 had the best performances in reduction the chemical parameters as well in terms of toxicity reduction. However, for the mine effluent the best (TiO2/UV and Fe2O3/UV) were only able to significantly remove three metals (Zn, Al and Cd). Nonetheless the treatments were able of reducing the toxicity of the effluent. As a final stage, the toxicity of solid wastes formed during wastewater treatment with NMs was assessed with Chironomus riparius larvae, a representative species of the sediment compartment. Certain solid wastes showed the potential to negatively affect C. riparius survival and growth, depending on the type of effluent treated. This work also brings new insights to the use of NMs for the treatment of industrial wastewaters. Although some potential applications have been announced, many evaluations have to be performed before the upscaling of the chemical treatments with NMs.