The clinical effect of dietary supplementation with omega-3 fish oils and/or copper in systemic lupus erythematosus.

OBJECTIVE: To determine the effect of dietary supplementation with omega-3 fish oils with or without copper on disease activity in systemic lupus erythematosus (SLE). Fish oil supplementation has a beneficial effect on murine models of SLE, while exogenous copper can decrease the formation of lupus erythematosus cells in rats with a hydralazine-induced collagen disease. METHODS: A double blind, double placebo controlled factorial trial was performed on 52 patients with SLE. Patients were randomly assigned to 4 treatment groups. Physiological doses of omega-3 fish oils and copper readily obtainable by dietary means were used. One group received 3 g MaxEPA and 3 mg copper, another 3 g MaxEPA and placebo copper, another 3 mg copper and placebo fish oil, and the fourth group received both placebo capsules. Serial measurements of disease activity using the revised Systemic Lupus Activity Measure (SLAM-R) and peripheral blood samples for routine hematological, biochemical, and immunological indices were taken at baseline, 6, 12, and 24 weeks. RESULTS: There was a significant decline in SLAM-R score from 6.12 to 4.69 (p <0.05) in those subjects taking fish oil compared to placebo. No significant effect on SLAM-R was observed in subjects taking copper. Laboratory variables were unaffected by either intervention. CONCLUSION: In the management of SLE, dietary supplementation with fish oil may be beneficial in modifying symptomatic disease activity.

Antibacterial activities of naturally occurring compounds against antibiotic-resistant Bacillus cereus vegetative cells and spores, Escherichia coli, and Staphylococcus aureus

After demonstrating the lack of effectiveness of standard antibiotics against the acquired antibiotic resistance of Bacillus cereus (NCTC 10989), Escherichia coli (NCTC 1186), and Staphylococcus aureus (ATCC 12715), we showed that the following natural substances were antibacterial against these resistant pathogens: cinnamon oil, oregano oil, thyme oil, carvacrol, (S)-perillaldehyde, 3,4-dihydroxybenzoic acid (beta-resorcylic acid), and 3,4-dihydroxyphenethylamine (dopamine). Exposure of the three pathogens to a dilution series of the test compounds showed that oregano oil was the most active substance. The oils and pure compounds exhibited exceptional activity against B. cereus vegetative cells, with oregano oil being active at nanogram, per milliliter levels. In contrast, activities against B. cereus spores were very low. Activities of the test compounds were in the following approximate order: oregano oil > thyme oil approximate to carvacrol > cinnamon oil > perillaldehyde > dopamine > beta-resorcylic acid. The order of susceptibilities of the pathogens to inactivation was as follows: B. cereus (vegetative) much greater than S. aureus approximate to E. coli much greater than B. cereus (spores). Some of the test substances may be effective against antibiotic-resistant bacteria in foods and feeds.

Identification of vegetable oil botanical speciation in refined vegetable oil blends using an innovative combination of chromatographic and spectroscopic techniques

European Regulation 1169/2011 requires producers of foods that contain refined vegetable oils to label the oil types. A novel rapid and staged methodology has been developed for the first time to identify common oil species in oil blends. The qualitative method consists of a combination of a Fourier Transform Infrared (FTIR) spectroscopy to profile the oils and fatty acid chromatographic analysis to confirm the composition of the oils when required. Calibration models and specific classification criteria were developed and all data were fused into a simple decision-making system. The single lab validation of the method demonstrated the very good performance (96% correct classification, 100% specificity, 4% false positive rate). Only a small fraction of the samples needed to be confirmed with the majority of oils identified rapidly using only the spectroscopic procedure. The results demonstrate the huge potential of the methodology for a wide range of oil authenticity work.

Antibacterial activities of naturally occurring compounds against Mycobacterium avium subsp. paratuberculosis.

The antibacterial activities of 18 naturally occurring compounds (including essential oils and some of their isolated constituents, apple and green tea polyphenols, and other plant extracts) against three strains of Mycobacterium avium subsp. paratuberculosis (a bovine isolate [NCTC 8578], a raw-milk isolate [806R], and a human isolate [ATCC 43015]) were evaluated using a macrobroth susceptibility testing method. M. avium subsp. paratuberculosis was grown in 4 ml Middlebrook 7H9 broth containing 10% oleic acid-albumin-dextrose-catalase, 0.05% Tween 80 (or 0.2% glycerol), and 2 µg/ml mycobactin J supplemented with five concentrations of each test compound. The changes in the optical densities of the cultures at 600 nm as a measure of CFU were recorded at intervals over an incubation period of 42 days at 37°C. Six of the compounds were found to inhibit the growth of M. avium subsp. paratuberculosis. The most effective compound was trans-cinnamaldehyde, with a MIC of 25.9 µg/ml, followed by cinnamon oil (26.2 µg/ml), oregano oil (68.2 µg/ml), carvacrol (72.2 µg/ml), 2,5-dihydroxybenzaldehyde (74 µg/ml), and 2-hydroxy-5-methoxybenzaldehyde (90.4 µg/ml). With the exception of carvacrol, a phenolic compound, three of the four most active compounds are aldehydes, suggesting that the structure of the phenolic group or the aldehyde group may be important to the antibacterial activity. No difference in compound activity was observed between the three M. avium subsp. paratuberculosis strains studied. Possible mechanisms of the antimicrobial effects are discussed.

Water-hydrophobic compound interactions with the microbial cell

The structural interactions of biological macromolecules, their biochemical activities and, ultimately, the metabolic function of cellular systems are dependent upon weak inter- and intra-molecular forces such as hydrogen bonds, Van der Waals forces, and the hydrophobic effect. Water molecules, and those of hydrophobic substances such as hydrocarbons, can take part in and/or modify these interactions and thereby determine the operational and structural stability of the microbial cell and its macromolecular systems. We explain how the cytosol, plasma membrane and the extracellular solution form a material and energetic continuum; and discuss the behavior of hydrophobic substances of extracellular origin as they migrate into the plasma membrane and into the cell's interior. The adverse effects of substances with a log P octanol-water =2, that partition into the hydrophobic domains of biological macromolecules, are discussed in relation to microbial cell function; and we speculate whether the cellular stress that they induce is symmetrical or asymmetrical in nature. In the context of the microbial environment, we take a situational-functional approach to consider how hydrophobic stressors interact with the microbial cell, and what types of evasion tactics microbes can employ to minimize their inhibitory activities. Finally, we discuss the ecological implications of hydrocarbon-induced cellular stress for microbial systems.

Exploring molecular recognition pathways within a family of gelators with different hydrogen bonding motifs

We report the synthesis of a family of gelators in which alkyl chains are connected to the amino groups of L-lysine methyl ester using a range of different hydrogen bonding linking groups (carbamate, amide, urea, thiourea and diacylhydrazine) using simple synthetic methodology based on isocyanate or acid chloride chemistry. The ability of these compounds to gelate organic solvents such as toluene or cyclohexane can be directly related to the ability of the linking group to form intermolecular hydrogen bonds. In general terms, the ability to structure solvents can be considered as: thiourea <carbamate <amide <urea similar to diacylhydrazine. This process has been confirmed by thermal measurements, scanning electron microscopy (SEM) and infrared and circular dichroism spectroscopies. By deprotecting the methyl ester group, we have demonstrated that a balance between hydrophobic and hydrophilic groups is essential-if the system has too much hydrophilicity (e. g., diacylhydrazine, urea) it will not form gels due to low solubility in the organic media. However, the less effective gelators based on amide and carbamate linkages are enhanced by converting the methyl ester to a carboxylic acid. Furthermore, subsequent mixing of the acid with a second component (diaminododecane) further enhances the ability to form networks, and, in the case of the amide, generates a two-component gel, which can immobilise a wide range of solvents of industrial interest including petrol and diesel (fuel oils), olive oil and sunflower oil (renewable food oils) and ethyl laurate, isopropyl myristate and isopropyl palmitate (oils used in pharmaceutical formulation). The gels are all thermoreversible, and may therefore be useful in controlled release/formulation applications.

DFT studies of long-chain FAMEs: theoretical justification for determining chain length and unsaturation from experimental Raman spectra

Density functional calculations, using B3LPY/6-31G(d) methods, have been used to investigate the conformations and vibrational (Raman) spectra of a series of long-chain, saturated fatty acid methyl esters (FAMEs) with the formula CH2nO2 (n = 5-21) and two series of unsaturated FAMEs. The calculations showed that the lowest energy conformer within the saturated FAMEs is the simple (all-trans) structure and, in general, it was possible to reproduce experimental data using calculations on only the all-trans conformer. The only exception was C6H12O2, where a second low-lying conformer had to be included in order to correctly simulate the experimental Raman spectrum. The objective of the work was to provide theoretical justification for the methods that are commonly used to determine the properties of the fats and oils, such as chain length and degree of unsaturation, from experimental Raman data. Here it is shown that the calculations reproduce the trends and calibration curves that are found experimentally and also allow the reasons for the failure of what would appear to be rational measurements to be understood. This work shows that although the assumption that each FAME can simply be treated as a collection of functional groups can be justified in some cases, many of the vibrational modes are complex motions of large sections of the molecules and thus would not be expected to show simple linear trends with changes in structure, such as increasing chain length and/or unsaturation. Simple linear trends obtained from experimental data may thus arise from cancellation of opposing effects, rather than reflecting an underlying simplicity.

Conformations, vibrational frequencies and Raman intensities of short-chain fatty acid methyl esters using DFT with 6-31G(d) and Sadlej pVTZ basis sets

Density functional calculations, using B3LPY/6-31G(d) methods, have been used to investigate the conformations and vibrational (Raman) spectra of three short-chain fatty acid methyl esters (FAMEs) with the formula CnH2nO2 (n = 3-5). In all three FAMEs, the lowest energy conformer has a simple 'all-trans' structure but there are other conformers, with different torsions about the backbone, which lie reasonably close in energy to the global minimum. One result of this is that the solid samples we studied do not appear to consist entirely of the lowest energy conformer. Indeed, to account for the 'extra' bands that were observed in the Raman data but were not predicted for the all-trans conformer, it was necessary to add-in contributions from other conformers before a complete set of vibrational assignments could be made. Provided this was done, the agreement between experimental Raman frequencies and 6-31G(d) values (after scaling) was excellent, RSD = 12.6 cm(-1). However, the agreement between predicted and observed intensities was much less satisfactory. To confirm the validity of the approach followed by the 6-3 1 G(d) basis set, we used a larger basis set, Sadlej pVTZ, and found that these calculations gave accurate Raman intensities and simulated spectra (summed from two different conformers) that were in quantitative agreement with experiment. In addition, the unscaled Sadlej pVTZ, and the scaled 6-3 1 G(d) calculations gave the same vibrational mode assignments for all bands in the experimental data. This work provides the foundation for calculations on longer-chain FAMEs (which are closer to those found as triglycerides in edible fats and oils) because it shows that scaled 6-3 1 G(d) calculations give equally accurate frequency predictions, and the same vibrational mode assignments, as the much more CPU-expensive Sadlej pVTZ basis set calculations.

Transesterification of vegetable oils on basic large mesoporous alumina supported alkaline fluorides-Evidences of the nature of the active site and catalytic performances

KF, LiF and CsF/A(2)O(3) catalysts with different loadings from 1 to 20 wt% were prepared using aqueous solutions of the alkaline fluoride compounds by wet impregnation of basic mesoporous MSU-type alumina. The catalysts were activated under At at 400 degrees C for 2 h and monitored by in situ XRD measurements. The catalysts were also characterized using several techniques: N-2 adsorption/desorption isotherms at -196 degrees C, FTIR, DR-UV-vis, CO2-TPD, XRD, Al-27 CP/MAS NMR. These characterizations led to the conclusion that the deposition of alkaline fluorides on the alumina surface generates fluoroaluminates and aluminate species. The process is definitivated at 400 degrees C. The fluorine in these structures is less basic than in the parent fluorides, but the oxygen becomes more basic. The catalysts were tested for the transesterification of fatty esters under different experimental conditions using conventional heating, microwave and Ultrasound irradiation. Recycling experiments showed that these catalysts are stable for a limited number of cycles. (C) 2009 Elsevier Inc. All rights reserved.

Desulfurisation of oils using ionic liquids: selection of cationic and anionic components to enhance extraction efficiency

Extraction of dibenzothiophene from dodecane using ionic liquids as the extracting phase has been investigated for a range of ionic liquids with varying cation classes (imidazolium, pyridinium, and pyrrolidinium) and a range of anion types using liquid-liquid partition studies and QSPR (quantitative structure-activity relationship) analysis. The partition ratio of dibenzothiophene to the ionic liquids showed a clear variation with cation class (dimethylpyridinium > methylpyridinium > pyridinium approximate to imidazolium approximate to pyrrolidinium), with much less significant variation with anion type. Polyaromatic quinolinium-based ionic liquids showed even greater extraction potential, but were compromised by higher melting points. For example, 1-butyl-6-methylquinolinium bis{(trifluoromethyl)sulfonyl} amide (mp 47 degrees C) extracted 90% of the available dibenzothiophene from dodecane at 60 degrees C.

The contents of proteins and phospholipids in cloudy (veiled) virgin olive oils

Extra virgin olive oil is produced in the form of a

Identification of oil mixtures in extracted and refined vegetable oils

Identification of adulteration in mechanically extracted oils or the botanical origin of refined vegetable oil blends can be effectively achieved through the combination of spectroscopic methods and chemometric techniques. Chromatographic methods remain highly relevant but suffer from various limitations which derive from natural compositional variation. Modern multivariate techniques have demonstrated that it is possible to identify patterns and effectively classify unknown samples in both cases. Development of robust analytical methodologies requires however vigorous validation. Spectroscopic methods combined with chemometric techniques lack established validation protocols and this might hinder their use by law enforcement authorities. 

Characterisation of UK and Irish Cold-Pressed Rapeseed Oils in Relation to Quality Indices and Constituents.

Cold-pressed rapeseed oil (CPRSO) is produced when seeds from an oilseed rape crop are mechanically crushed whilst at a low temperature. CPRSO’s popularity is rapidly expanding and is now produced in most Northern European countries including both N.Ireland and ROI. The CPRSO industry is still relatively new and therefore not as widely researched as other high quality oils. Fifteen CPRSO from The UK, Ireland and France were examined to determine characteristic differences between the oils. Two samples of extra-virgin olive oil and two samples of refined rapeseed oil were also included in the investigation to assess performance against market competitors. The antioxidant potential of the oils was assessed using the ABTS and DPPH radical scavenging assays. Both unexpectedly showed that refined rapeseed oil had the highest potential whilst there was significant difference between many of the CPRSO’s. The acid value (ACOS method Cd 3d-63) ranged widely from 0.47-3.41. To predict the stability during storage, an accelerated oxidation test was carried out where the oils were placed in an oven (60°C) and peroxide value was monitored. The results showed extra-virgin olive oil underwent the least oxidation during the trial. The refined rapeseed oil suffered the worst levels of oxidation whilst the CPRSO’s performed similarly but with some variation. Fatty acid composition was investigated with GC-MS and some of the major fatty acids were found to differ significantly between producers. Minor compound analysis was achieved with extraction and identification through HPLC. All results are critically discussed and compared to relevant published studies.