Mechanical properties of structures 3D printed with cementitious powders

The three dimensional (3D) printing technology has undergone rapid development in the last few years and it is now possible to print engineering structures. This paper presents a study of the mechanical behavior of 3D printed structures using cementitious powder. Microscopic observation reveals that the 3D printed products have a layered orthotropic microstructure, in which each layer consists of parallel strips. Compression and flexural tests were conducted to determine the mechanical properties and failure characteristics of such materials. The test results confirmed that the 3D printed structures are laminated with apparent orthotropy. Based on the experimental results, a stress-strain relationship and a failure criterion based on the maximum stress criterion for orthotropic materials are proposed for the structures of 3D printed material. Finally, a finite element analysis was conducted for a 3D printed shell structure, which shows that the printing direction has a significant influence on the load bearing capacity of the structure.

Butt out - baby on board

It is estimated that the cost of treating women and their infants with smoking related problems is up to £87.5 million each year (ASH, 2013). Whilst these statistics depict a major problem for the National Health Service, they challenge midwives to become change agents within this health promotion area. A desired outcome from The Maternity Strategy for Northern Ireland (DHSSPSNI, 2012) includes giving every baby and family the best start in life. Assisting women to stop smoking before conception, could help to achieve this outcome and provide opportunities for a greater start in life following birth.

An evaluation of palliative care services for cancer patients in the Southern Health and Social Services Board of Northern Ireland.

An interview study of 55 lay carers of people who died from cancer in the Southern Board of Northern Ireland was undertaken using a combination of closed-format and open-ended questions. The aim of the study was to evaluate palliative care services delivered in the last six months of their lives to cancer patients who died either at home or in hospital. Two-thirds of the deaths (36) occurred in the domestic home, 45 of the deceased were admitted as hospital inpatients, and the great majority were in receipt of community nursing (53) and general practitioner (54) services. Open-ended questions were used to allow respondents to give their views about services in some detail and their views about good and bad aspects of services were sought. While they were generally satisfied with services specific areas of difficulty were identified in each aspect of care addressed by the study. The most favourable assessments were made of community nursing with the greatest number of negative comments being made about inpatient hospital care. Differing interests between some of those who were dying and their lay carers were found in two areas: the receipt of help from nonfamily members and the information that the deceased received about their terminal status.

Board invited review:The importance of the gestation period for welfare of calves: Maternal stressors and difficult births

The prenatal period is of critical importance in defining how individuals respond to their environment throughout life. Stress experienced by pregnant females has been shown to have detrimental effects on offspring biology in humans and a variety of other species. It also is becoming increasingly apparent that prenatal events can have important consequences for the behavior, health, and productivity of offspring in farmed species. Pregnant cattle may experience many potentially important stressors, for instance, relating to their social environment, housing system and physical environment, interactions with humans and husbandry procedures, and their state of health. We examined the available literature to provide a review of the implications of prenatal stress for offspring welfare in cattle. The long-term effects of dystocia on cattle offspring also are reviewed. To ensure a transparent and repeatable selection process, a systematic review approach was adopted. The research literature clearly demonstrates that prenatal stress and difficult births in beef and dairy cattle both have implications for offspring welfare and performance. Common husbandry practices, such as transport, were shown to influence offspring biology and the importance of environmental variables, including thermal stress and drought, also were highlighted. Maternal disease during pregnancy was shown to negatively impact offspring welfare. Moreover, dystocia-affected calves suffer increased mortality and morbidity, decreased transfer of passive immunity, and important physiological and behavioral changes. This review also identified considerable gaps in our knowledge and understanding of the effects of prenatal stress in cattle. © 2012 American Society of Animal Science. All rights reserved.

Passive Intermodulation in Distributed Circuits with Cascaded Discrete Nonlinearities

The principle aspects of passive intermodulation (PIM) characterisation in distributed printed circuits with cascaded lumped nonlinearities are presented. Mechanisms of PIM generations have been investigated experimentally and modelled using the formalism of X-parameters. The devised equivalent circuit models are applied to the analysis of microstrip lines with distributed and cascaded lumped sources of nonlinearity. The dynamic measurements have revealed that PIM generation rates in straight and meandered microstrip lines differ and significantly deviate from those expected for the respective discrete sources of nonlinearity. The obtained results indicate that multiple physical sources of nonlinearity contribute to PIM generation in printed circuits. Finally, it is demonstrated that the electrical discontinuities can have significant effect on the overall PIM response of the distributed passive circuits and cause PIM product leakage and parasitic coupling between isolated circuit elements.

Closed circuit rebreathing to achieve inert gas wash-in for multiple breath wash-out

Multiple breath wash-out (MBW) testing requires prior wash-in of inert tracer gas. Wash-in efficiency can be enhanced by a rebreathing tracer in a closed circuit. Previous attempts to deploy this did not account for the impact of CO2 accumulation on patients and were unsuccessful. We hypothesised that an effective rebreathe wash-in could be delivered and it would not alter wash-out parameters. Computer modelling was used to assess the impact of the rebreathe method on wash-in efficiency. Clinical testing of open and closed circuit wash-in–wash-out was performed in healthy controls and adult patients with cystic fibrosis (CF) using a circuit with an effective CO2 scrubber and a refined wash-in protocol. Wash-in efficiency was enhanced by rebreathing. There was no difference in mean lung clearance index between the two wash-in methods for controls (6.5 versus 6.4; p=0.2, n=12) or patients with CF (10.9 versus 10.8; p=0.2, n=19). Test time was reduced by rebreathe wash-in (156 versus 230 s for CF patients, p<0.001) and both methods were well tolerated. End wash-in CO2 was maintained below 2% in most cases. Rebreathe–wash-in is a promising development that, when correctly deployed, reduces wash-in time and facilitates portable MBW testing. For mild CF, wash-out outcomes are equivalent to an open circuit.

Equivalent Circuit Model of Twisted Split Ring Frequency Selective Surfaces

This paper proposes a wideband equivalent circuit model for a twisted split ring frequency selective surface (FSS). Such surfaces can be used for modelling and design of polarisation sensitive surfaces such as circularly polarized selective surfaces as well as structures with asymmetric transmission. The proposed model is based extraction of equivalent circuit parameters from a single split ring (SRR) FSS and magnetic coupling from periodic eigenmode analysis of the coupled SRR. The resulting equivalent circuit model demonstrates excellent agreement with full-wave simulations.

Effects of Poly (ε-caprolactone) Coating on the Properties of Three-Dimensional Printed Porous Structures

Powder-based inkjet three-dimensional printing (3DP) to fabricate pre-designed 3D structures has drawn increasing attention. However there are intrinsic limitations associated with 3DP technology due to the weak bonding within the printed structure, which significantly compromises its mechanical integrity. In this study, calcium sulphate ceramic structures demonstrating a porous architecture were manufactured using 3DP technology and subsequently post-processed with a poly (ε-caprolactone) (PCL) coating. PCL concentration, immersion time, and number of coating layers were the principal parameters investigated and improvement in compressive properties was the measure of success. Interparticle spacing within the 3DP structures were successfully filled with PCL material. Consequently the compressive properties, wettability, morphology, and in vitro resorption behaviour of 3DP components were significantly augmented. The average compressive strength, Young’s modulus, and toughness increased 217%, 250%, and 315%, following PCL coating. Addition of a PCL surface coating provided long-term structural support to the host ceramic material, extending the resorption period from less than 7 days to a minimum of 56 days. This study has demonstrated that application of a PCL coating onto a ceramic 3DP structure was a highly effective approach to addressing some of the limitations of 3DP manufacturing and allows this advanced technology to be potentially used in a wider range of applications.