Modelling lay-up automation and production rate interaction on the cost of large stiffened panel components

This paper presents an integrated design and costing method for large stiffened panels for the purpose of investigating the influence and interaction of lay-up technology and production rate on manufacturing cost. A series of wing cover panels (≈586kg, 19·9m2) have been sized with realistic requirements considering manual and automated lay-up routes. The integrated method has enabled the quantification of component unit cost sensitivity to changes in annual production rate and employed equipment maximum deposition rate. Moreover the results demonstrate the interconnected relationship between lay-up process and panel design, and unit cost. The optimum unit cost solution when using automated lay-up is a combination of the minimum deposition rate and minimum number of lay-up machines to meet the required production rate. However, the location of the optimum unit cost, at the boundaries between the number of lay-up machines required, can make unit cost very sensitive to small changes in component design, production rate, and equipment maximum deposition rate. - See more at: http://aerosociety.com/News/Publications/Aero-Journal/Online/1941/Modelling-layup-automation-and-production-rate-interaction-on-the-cost-of-large-stiffened-panel-components#sthash.0fLuu9iG.dpuf

Rapid design of discrete orthonormal wavelet transforms using silicon IP components

A rapid design methodology for orthonormal wavelet transform cores has been developed. This methodology is based on a generic, scaleable architecture utilising time-interleaved coefficients for the wavelet transform filters. The architecture has been captured in VHDL and parameterised in terms of wavelet family, wavelet type, data word length and coefficient word length. The control circuit is embedded within the cores and allows them to be cascaded without any interface glue logic for any desired level of decomposition. Case studies for stand alone and cascaded silicon cores for single and multi-stage wavelet analysis respectively are reported. The design time to produce silicon layout of a wavelet based system has been reduced to typically less than a day. The cores are comparable in area and performance to handcrafted designs. The designs are portable across a range of foundries and are also applicable to FPGA and PLD implementations.

Robot and insect navigation by polarized skylight

A study of a large number of published experiments on the behaviour of insects navigating by skylight has led to the design of a system for navigation in lightly clouded skies, suitable for a robot or drone. The design is based on the measurement of the directions in the sky at which the polarization angle, i.e. the angle χ between the polarized E-vector and the meridian, equals ±π/4 or ±(π/4 + π/3) or ±(π/4 - π/3). For any one of these three options, at any given elevation, there are usually 4 such directions and these directions can give the azimuth of the sun accurately in a few short steps, as an insect can do. A simulation shows that this compass is accurate as well as simple and well suited for an insect or robot. A major advantage of this design is that it is close to being invariant to variable cloud cover. Also if at least two of these 12 directions are observed the solar azimuth can still be found by a robot, and possibly by an insect.

Tiotropium and olodaterol fixed-dose combination versus mono-components in COPD (GOLD 2-4)

Efficacy and safety of tiotropium+olodaterol fixed-dose combination (FDC) compared with the mono-components was evaluated in patients with moderate to very severe chronic obstructive pulmonary disease (COPD) in two replicate, randomised, double-blind, parallel-group, multicentre, phase III trials. Patients received tiotropium+olodaterol FDC 2.5/5 μg or 5/5 μg, tiotropium 2.5 μg or 5 μg, or olodaterol 5 μg delivered once-daily via Respimat inhaler over 52 weeks. Primary end points were forced expiratory volume in 1 s (FEV1) area under the curve from 0 to 3 h (AUC0-3) response, trough FEV1 response and St George's Respiratory Questionnaire (SGRQ) total score at 24 weeks. In total, 5162 patients (2624 in Study 1237.5 and 2538 in Study 1237.6) received treatment. Both FDCs significantly improved FEV1 AUC0-3 and trough FEV1 response versus the mono-components in both studies. Statistically significant improvements in SGRQ total score versus the mono-components were only seen for tiotropium+olodaterol FDC 5/5 μg. Incidence of adverse events was comparable between the FDCs and the mono-components. These studies demonstrated significant improvements in lung function and health-related quality of life with once-daily tiotropium+olodaterol FDC versus mono-components over 1 year in patients with moderate to very severe COPD.

Stress tolerance and virulence of insect-pathogenic fungi are determined by environmental conditions during conidial formation

The virulence to insects and tolerance to heat and UV-B radiation of conidia of entomopathogenic fungi are greatly influenced by physical, chemical, and nutritional conditions during mycelial growth. This is evidenced, for example, by the stress phenotypes of Metarhizium robertsii produced on various substrates. Conidia from minimal medium (Czapek's medium without sucrose), complex medium, and insect (Lepidoptera and Coleoptera) cadavers had high, moderate, and poor tolerance to UV-B radiation, respectively. Furthermore, conidia from minimal medium germinated faster and had increased heat tolerance and were more virulent to insects than those from complex medium. Low water-activity or alkaline culture conditions also resulted in production of conidia with high tolerance to heat or UV-B radiation. Conidia produced on complex media exhibited lower stress tolerance, whereas those from complex media supplemented with NaCl or KCl (to reduce water activity) were more tolerant to heat and UV-B than those from the unmodified complex medium. Osmotic and nutritive stresses resulted in production of conidia with a robust stress phenotype, but also were associated with low conidial yield. Physical conditions such as growth under illumination, hypoxic conditions, and heat shock before conidial production also induced both higher UV-B and heat tolerance; but conidial production was not decreased. In conclusion, physical and chemical parameters, as well as nutrition source, can induce great variability in conidial tolerance to stress for entomopathogenic fungi. Implications are discussed in relation to the ecology of entomopathogenic fungi in the field, and to their use for biological control. This review will cover recent technologies on improving stress tolerance of entomopathogenic fungi for biological control of insects.