Pull-out behaviour of axially loaded basalt fibre reinforced polymer (BFRP) rods bonded parallel to the grain of glulam elements

Synopsis: Bonded-in rod timber joints off er several advantages over conventional types of joint, including high local force transfer, very stiff connections, and improved ?re and aesthetic properties since the connection is completely hidden in the insulating timber members. More recently, the use of ?bre reinforced polymer (FRP) as a connecting rod, alternative to steel rods, in bonded-in rod connections for timber structures has been investigated. However, the investigation into the behaviour of such joints is limited, in particular, connections involving basalt ?bre reinforced polymers (BFRP) bars - which is the primary focus of this research. This paper presents an experimental programme conducted to investigate the behaviour of bonded-in BFRP bars loaded parallel to the grain of glulam members. Tensile pull-out tests were conducted to examine the effect of bonded length and bond stress-slip on the structural capacity of the connection. An analytical design expression for predicting pull-out capacity is proposed and the results have been compared with some established design equations. It was found that pull-out load increased approximately linearly with the bonded length, up to maximum which occurred at a bonded length of 15 times the hole diameter, and did not increase beyond this bonded length. The most signi?cant failure modes were failure at the timber/adhesive interface followed by pullout of the BFRP rod. Increased bonded lengths resulted in higher bond slip values compared to lower equivalent bonded lengths. The proposed design model gave the best predictions of pull-out capacity compared with other existing models.

Norberg-Schulz’ Elements of Space in Dark City

Alex Proyas' science fiction film Dark City (1998) puts forth questions about the building process of a city. The aliens in the film constantly alter each street, building and room to create the right environment for humans to dwell. The ‘strangers’ believe that they need to study humans in their spaces to understand human nature. They use bits and pieces of people's memories to reconstruct the city.

Christian Norberg-Schulz identifies four elements of space: physical, perceptual, existential and conceptual. Physical space is physical existence as it is. Perceptual space is the temporary space the user perceives. Existential space, for instance, the meaning of the concept of home, is abstract and permanent; it does not change with changing conditions. Finally, conceptual space, in his spatial philosophy, is the space concept of specialists like architects, economists and mathematicians.

This article analyses the future noir environment of Dark City from a spatial perspective. The notion of building is studied as to physical, perceptual, existential and conceptual spaces of Norberg-Schulz through concepts of home, identity, belonging, and alienation with reference to the architecture of the city.

Essential and toxic elements in infant foods from Spain, UK, China and USA

Spanish gluten-free rice, cereals with gluten, and pureed baby foods were analysed for essential macro-elements (Ca and Na), essential trace elements (Fe, Cu, Zn, Mn, Se, Cr, Co and Ni) and non-essential trace elements (As, Pb, Cd and Hg) using ICP-MS and AAS. Baby cereals were an excellent source of most of the essential elements (Ca, Fe, Cu, Mn and Zn). Sodium content was high in pureed foods to improve their flavour; fish products were also rich in Se. USA pure baby rice samples had the highest contents of all studied essential elements, showing a different nutrient pattern compared to those of other countries. Mineral fortification was not always properly stated in the labelling of infant foods. Complementary infant foods may also contain significant amounts of contaminants. The contents of Hg and Cd were low enough to guarantee the safety of these infant foods. However, it will be necessary to identify the source and reduce the levels of Pb, Cr and As in Spanish foods. Pure baby rice samples contained too much: Pb in Spain; As in UK; As, Cr and Ni in USA; and Cr and Cd in China.

Risk assessment of potentially toxic elements in agricultural soils and maize tissues from selected districts in Tanzania

A field survey was conducted to investigate the contamination of potentially toxic elements (PTEs) arsenic (As), lead (Pb), chromium (Cr), and nickel (Ni) in Tanzanian agricultural soils and to evaluate their uptake and translocation in maize as proxy to the safety of maize used for human and animal consumption. Soils and maize tissues were sampled from 40 farms in Tanzania and analyzed using inductively coupled plasma-mass spectrometry in the United Kingdom. The results showed high levels of PTEs in both soils and maize tissues above the recommended limits. Nickel levels of up to 34.4 and 56.9mgkg(-1) respectively were found in some maize shoots and grains from several districts. Also, high Pb levels >0.2mgkg(-1) were found in some grains. The grains and shoots with high levels of Ni and Pb are unfit for human and animal consumption. Concentrations of individual elements in maize tissues and soils did not correlate and showed differences in uptake and translocation. However, Ni showed a more efficient transfer from soils to shoots than As, Pb and Cr. Transfer of Cr and Ni from shoots to grains was higher than other elements, implying that whatever amount is assimilated in maize shoots is efficiently mobilized and transferred to grains. Thus, the study recommended to the public to stop consuming and feeding their animals maize with high levels of PTEs for their safety.

Inorganic arsenic and trace elements in Ghanaian grain staples

A total of 549 samples of rice, maize, wheat, sorghum and millet were obtained from markets in Ghana, the EU, US and Asia. Analysis of the samples, originating from 21 countries in 5 continents, helped to establish global mean trace element concentrations in grains: thus placing the Ghanaian data within a global context. Ghanaian rice was generally low in potentially toxic elements, but high in essential nutrient elements. Arsenic concentrations in rice from US (0.22 mg/kg) and Thailand (0.15 mg/kg) were higher than in Ghanaian rice (0.11 mg/kg). Percentage inorganic arsenic content of the latter (83%) was, however, higher than for US (42%) and Thai rice (67%). Total arsenic concentration in Ghanaian maize, sorghum and millet samples (0.01 mg/kg) was an order of magnitude lower than in Ghanaian rice, indicating that a shift from rice-centric to multigrain diets could help reduce health risks posed by dietary exposure to inorganic As. (C) 2011 Elsevier Ltd. All rights reserved.

An Experimental and Numerical Study of the Static and Fatigue Performance of a Composite Adhesive Repair

Experimental static and fatigue tension-tension tests were carried out on 5HS/RTM6 composite intact coupons and coupons incorporating adhesively-bonded (FM300-2) stepped flush joints. The results show that the adhesive joint, which is widely used in repairs, significantly reduces the static strength as well as the fatigue life of the composite. Both, the static and the fatigue failure of the ‘repaired’ coupons occur at the adhesive joint and involve crack initiation and propagation. The latter is modelled using interface finite elements based on the decohezive zone approach. The material degradation in the interface constitutive law is described by a damage variable, which can evolve due to the applied loads as well as the number of fatigue cycles. The fatigue formulation, based on a published model, is adapted to fit the framework of the pseudotransient formulation that is used as a numerical tool to overcome convergence difficulties. The fatigue model requires three material parameters. Numerical tests show that a single set of these parameters can be used to recover, very accurately, the experimental S-N relationship. Sensitivity studies show that the results are not mesh dependent.

Automatic Insertion of Cohesive Elements for Delamination

Composite damage modelling with cohesive elements has initially been limited to the analysis of interface damage or delamination. However, their use is also being extended to the analysis of inplane tensile failure arising from matrix or fibre fracture. These interface elements are typically placed at locations where failure is likely to occur, which infers a certain a priori knowledge of the crack propagation path(s). In the case of a crack jump for example, the location of the jump is usually not obvious, and the simulation would require the placement of cohesive elements at all element faces. A better option, presented here, is to determine the potential location of cohesive elements and insert them during the analysis. The aim of this work is to enable the determination of the crack path, as part of the solution process. A subroutine has been developed and implemented in the commercial finite element package ABAQUS/Standard[1] in order to automatically insert cohesive elements within a pristine model, on the basis of the analysis of the current stress field. Results for the prediction of delamination are presented in this paper.

A progressive failure model for composite laminates subjected to low velocity impact damage

This paper presents a 3-D failure model for predicting the dynamic material response of composite laminates under impact loading. The formulation is based on the Continuum Damage Mechanics (CDM) approach and enables the control of the energy dissipation associated with each failure mode regardless of mesh refinement and fracture plane orientation. Internal thermodynamically irreversible damage variables were defined in order to quantify damage concentration associated with each possible failure mode and predict the gradual stiffness reduction during the impact damage process. The material model has been implemented into LS-DYNA explicit finite element code within solid elements and it has proven to be capable of reproducing experimental results with good accuracy in terms of static/dynamic responses, absorbed energy and extent of damage.

Pull-out behaviour of axially loaded Basalt Fibre Reinforced Polymer (BFRP) rods bonded perpendicular to the grain of glulam elements

The behaviour of Basalt Fibre Reinforced Polymer (BFRP) loaded perpendicular to glulam timber elements was investigated. It was found that pull-out load increased approximately linearly with the bonded length up to maximum which occurred at a bonded length of 250 mm (~15 times the hole diameter) and did not increase beyond this bonded length. Failure mode of the samples was mostly shear fracture which was located at the cylindrical zone at the timber/adhesive interface. Increased bonded lengths resulted in corresponding decrease in interfacial bond stress. At 250 mm bonded length, the pull-out capacity of the proposed design model was about 2% lower than that of the tests. The results also showed that the bond stress of the theoretical model (at the ascending and descending branches) of the stress–slip curve was approximately 5–10% of that of the experiment.

Design and experimental validation of liquid crystal-based reconfigurable reflectarray elements with improved bandwith in F-band

A reconfigurable reflectarray which exploits the dielectric anisotropy of liquid crystals (LC) has been designed to operate in the frequency range from 96 to 104 GHz. The unit cells are composed of three unequal length parallel dipoles placed above an LC substrate. The reflectarray has been designed using an accurate model which includes the effects of anisotropy and inhomogeneity. An effective permittivity that accounts for the real effects of the LC has also been used to simplify the analysis and design of the unit cells. The geometrical parameters of the cells have been adjusted to simultaneously improve the bandwidth, maximize the tunable phase-range and reduce the sensitivity to the angle of incidence. The performance of the LC based unit cells has been experimentally evaluated by measuring the reflection amplitude and phase of a reflectarray consisting of 52x54 identical cells. The good agreement between measurements and simulations validate the analysis and design techniques and demonstrate the capabilities of the proposed reflectarray to provide beam scanning in F band.

Investigating local relationships between trace elements in soils and cancer data

Medical geology research has recognised a number of potentially toxic elements (PTEs), such as arsenic, cobalt, chromium, copper, nickel, lead, vanadium, uranium and zinc, known to influence human disease by their respective deficiency or toxicity. As the impact of infectious diseases has decreased and the population ages, so cancer has become the most common cause of death in developed countries including Northern Ireland. This research explores the relationship between environmental exposure to potentially toxic elements in soil and cancer disease data across Northern Ireland. The incidence of twelve different cancer types (lung, stomach, leukaemia, oesophagus, colorectal, bladder, kidney, breast, mesothelioma, melanoma and non melanoma(NM) both basal and squamous, were examined in the form of twenty-five coded datasets comprising aggregates over the 12 year period from 1993 to 2006. A local modelling technique,geographically weighted regression (GWR) is usedto explore the relationship between environmental exposure and cancer disease data. The results show comparisons of the geographical incidence of certain cancers (stomach and NM squamous skin cancer) in relation to concentrations of certain PTEs (arsenic levels in soils and radon were identified). Findings from the research have implications for regional human health risk assessments.