Experimental Investigation of Stretch Blow Molding, Part 1: Instrumentation in an Industrial Environment

In spite of intensive research, computational modeling of the injection stretch blow molding (ISBM) still cannot match the accuracy of other polymer processes such as injection molding. There is a lack of understanding of the interdependence among the machine parameters set up by the operators, process parameters, material behavior, and the resulting final thickness distribution and performance of the molded product. The work presented in this paper describes a set of instrumentation tools developed for investigation of the ISBM process in an industrial setting. Results are presented showing the pressure and air temperature evolution inside the mold, the stretch rod force and displacement history, and the moment of contact of the polymer with seven discrete locations on the mold.

A nearly real-time high temperature laser-plasma diagnostic using photonuclear reactions in tantalum

A method of measuring the temperature of the fast electrons produced in ultraintense laser-plasma interactions is described by inducing photonuclear reactions, in particular (gamma,n) and (gamma,3n) reactions in tantalum. Analysis of the gamma rays emitted by the daughter nuclei of these reactions using a germanium counter enables a relatively straightforward near real-time temperature measurement to be made. This is especially important for high temperature plasmas where alternative diagnostic techniques are usually difficult and time consuming. This technique can be used while other experiments are being conducted. (C) 2002 American Institute of Physics.

TECHNICAL NOTE. A BRIEF REVIEW OF METHODS FOR MEASURING THE PERMEATION PROPERTIES OF CONCRETE IN SITU

Numerous methods are available to measure the permeation properties of concrete, which can be classified in terms of the diffusion, absorption and permeability properties. The results from these tests are generally used to infer 'quality' or relative durability. Some of these tests involve the laboratory assessment of a sample of concrete extracted from the structure. However, this Technical Note concentrates on the alternative methods appropriate for use on site. Guidance is given on the choice of an appropriate test method, which in most practical situations depends on the predominant mechanism acting on the concrete under consideration.

Predicting die life from die temperature for high pressure dies casting

The objective of this research was to determine the surface temperature of a high pressure die casting die during casting conditions. This was achieved by instrumentation of an insert which was placed in the shotplate region of the die. This research overcame the challenge of directly measuring the die surface temperature during a HPDC production casting cycle and shows that this is an effective method to determine the die surface temperature during the casting cycle. The instrumentation results gave a peak and minimum temperature of 500 C and 240 C respectively during steady state running conditions with a molten aluminium casting temperature of 660 C. Stress analysis from the steady state measured temperature of the die surface was calculated through a simple FEA model and the resulting stress uctuation was applied to a fatigue equation for the die material, the predicted number of cycles for cracking to start was found to correlate well with observed die damage.

Measuring positron-atom binding energies through laser-assisted photorecombination

Described here is a proposed experiment to use laser-assisted photorecombination of positrons from a trap-based beam and metal atoms in the gas phase to measure positron-atom binding energies. Signal rates are estimated, based in part upon experience studying resonant annihilation spectra using a trapbased positron beam. © IOP Publishing Ltd and Deutsche Physikalische Gesellschaft.

Stress correlation between instrumentation and simulation analysis of the die for high pressure die casting

A strain gauge instrumentation trial on a high pressure die casting ‘HPDC’ die was compared to a corresponding simulation model using Magmasoft® casting simulation software at two strain gauge rosette locations. The strains were measured during the casting cycle, from which the von Mises stress was determined and then compared to the simulation model. The von Mises stress from the simulation model correlated well with the findings from the instrumentation trial, showing a difference of 5.5%, ~ 10 MPa for one strain gauge rosette located in an area of low stress gradient. The second rosette was in a region of steep stress gradient, which resulted in a difference of up to 40%, ~40 MPa between the simulation and instrumentation results. Factors such as additional loading from die closure force or metal injection pressure which are not modelled by Magmasoft® were seen to have very little influence on the stress in the die, less than 7%.