Trends in product recalls within the agri-food industry:Empirical evidence from the USA, UK and the Republic of Ireland

The increasing frequency of product recalls within the agri-food industry has led many to question food safety. Research studies also often focus on biological hazards without considering how past, present and emerging risks change over time. We undertake a systematic review of the different biological, operational and chemical hazards within the agri-food industry using a dataset of 2070 registered food recalls in the USA, UK and Republic of Ireland between 2004 and 2010. We show product recalls have become more frequent over time and operational hazards, rather than biological and chemical hazards, are the most frequent recall type within the agri-food industry. © 2012 Elsevier Ltd. All rights reserved.

A Novel Method to Enable Trade-offs Across the Whole Product Life of an Aircraft Using Value Driven Design

The increasing need to understand complex products and systems with long life spans, presents a significant challenge to designers who increasingly require a broader understanding of the operational aspects of the system. This demands an evolution in current design practice, as designers are often constrained to provide a subsystem solution without full knowledge of the global system operation. Recently there has been a push to consider value centric approaches which should facilitate better or more rapid convergence to design solutions with predictable completion schedules. Value Driven Design is one such approach, in which value is used as the system top level objective function. This provides a broader view of the system and enables all sub-systems and components to be designed with a view to the effect on project value. It also has the capacity to include value expressions for more qualitative aspects, such as environmental impact. However, application of the method to date has been restricted to comparing value in a programme where the lifespan is fixed and known a priori. This paper takes a novel view of value driven design through the surplus value objective function, and shows how it can be used to identify key sensitivities to guide designers in design trade-off decisions. By considering a new time based approach it can be used to identify optimum programme life-span and hence allow trade-offs over the whole product life.

Product standardisation as a tool to control prescribing costs a case study of alginate liquid preparations

Introduction Product standardisation involves promoting the prescribing of pre-selected products within a particular category across a healthcare region and is designed to improve patient safety by promoting continuity of medicine use across the primary/secondary care interface, in addition to cost containment without compromising clinical care (i.e. maintaining safety and efficacy). Objectives To examine the impact of product standardisation on the prescribing of compound alginate preparations within primary care in Northern Ireland. Methods Data were obtained on alginate prescribing from the Northern Ireland Central Services Agency (Prescription Pricing Branch), covering a period of 43 months. Two standardisation promotion interventions were carried out at months 18 and 33. In addition to conventional statistical analyses, a simple interrupted time series analysis approach, using graphical interpretation, was used to facilitate interpretation of the data. Results There was a significant increase in the prescribed share of the preferred alginate product in each of the four health boards in Northern Ireland and a decrease in the cost per Defined Daily Dose for alginate liquid preparations overall. Compliance with the standardisation policy was, however, incomplete and was influenced to a marked degree by the activities of the pharmaceutical industry. The overall economic impact of the prescribing changes during the study was small (3.1%). Conclusion The findings suggested that product standardisation significantly influenced the prescribing pattern for compound alginate liquid preparations within primary care across Northern Ireland. © 2012 The Authors. IJPP © 2012 Royal Pharmaceutical Society.

In Vitro UDP-Sugar:Undecaprenyl-Phosphate Sugar-1-Phosphate Transferase Assay and Product Detection by Thin Layer Chromatography

In vitro assays are invaluable for the biochemical characterization of UDP-sugar:undecaprenyl-phosphate sugar-1-phosphate transferases. These assays typically involve the use of a radiolabeled substrate and subsequent extraction of the product, which resides in a lipid environment. Here, we describe the preparation of bacterial membranes containing these enzymes, a standard in vitro transferase assay with solvents containing chloroform and methanol, and two methods to measure product formation: scintillation counting and thin layer chromatography.

EFFECT OF IMPELLER DESIGN ON PRODUCT HOMOGENIETY IN HIGH SHEAR WET GRANULATION

Design of small mixer impellers is not tailored for granulation as they are designed for a wide range of processes. The Kenwood KM070 was employed as a standard apparatus to undertake this investigation. Five different impeller designs were used, possessing different shapes and surface areas. The aim of this research was to evaluate the performances of these impellers to provide
guidance on the selection and design for the purposes of granulation. Lactose granules were produced using wet granulation with water as the binder.
The efficacy of respective granulates was measured by adding an optically
sensitive tracer.This was used to determine powder concentrations
within various regions of the granulator. It was found that impeller design influenced the homogeneity of the granules; and therefore can affect final product performance.

The effect of polymer coatings on physicochemical properties of spray-dried liposomes for nasal delivery of BSA

This work describes the development of spray dried polymer coated liposomes composed of soy phosphatidylcholine (SPC) and phospholipid dimyristoyl phosphatidylglycerol (DMPG) coated with alginate, chitosan or trimethyl chitosan (TMC), that are able to penetrate through the nasal mucosa and offer enhanced penetration over uncoated liposomes when delivered as a dry powder. All the liposome formulations, loaded with BSA as model antigen, were spray-dried to obtain powder size and liposome size in a suitable range for nasal delivery. Although coating resulted in some reduction in encapsulation efficiency, levels were still maintained between 60% and 69% and the structural integrity of the entrapped protein and its release characteristics were maintained. Coating with TMC gave the best product characteristics in terms of entrapment efficiency, glass transition (Tg) and mucoadhesive strength, while penetration of nasal mucosal tissue was very encouraging when these liposomes were administered as dispersions although improved results were observed for the dry powders

The advanced glycation end product, Nepsilon-(carboxymethyl)lysine, is a product of both lipid peroxidation and glycoxidation reactions

Nepsilon-(Carboxymethyl)lysine (CML) is an advanced glycation end product formed on protein by combined nonenzymatic glycation and oxidation (glycoxidation) reactions. We now report that CML is also formed during metal-catalyzed oxidation of polyunsaturated fatty acids in the presence of protein. During copper-catalyzed oxidation in vitro, the CML content of low density lipoprotein increased in concert with conjugated dienes but was independent of the presence of the Amadori compound, fructoselysine, on the protein. CML was also formed in a time-dependent manner in RNase incubated under aerobic conditions in phosphate buffer containing arachidonate or linoleate; only trace amounts of CML were formed from oleate. After 6 days of incubation the yield of CML in RNase from arachidonate was approximately 0.7 mmol/mol lysine compared with only 0.03 mmol/mol lysine for protein incubated under the same conditions with glucose. Glyoxal, a known precursor of CML, was also formed during incubation of RNase with arachidonate. These results suggest that lipid peroxidation, as well as glycoxidation, may be an important source of CML in tissue proteins in vivo and that CML may be a general marker of oxidative stress and long term damage to protein in aging, atherosclerosis, and diabetes.

The efficacy of a CDIO based integrated curriculum as preparation for professional practice in product design and development

The School of Mechanical and Aerospace Engineering at Queen’s University Belfast started BEng and MEng degree programmes in Product Design and Development (PDD) in 2004. Intended from the outset to be significantly different from the existing programmes within the School the PDD degrees used the syllabus and standards defined by the CDIO Initiative as the basis for an integrated curriculum. Students are taught in the context of conceiving, designing, implementing and operating a product. Fundamental to this approach is a core sequence of Design-Build-Test (DBT) experiences which facilitates the development of a range of professional skills as well as the immediate application of technical knowledge gained in strategically aligned supporting modules.
The key objective of the degree programmes is to better prepare students for professional practice. PDD graduates were surveyed using a questionnaire developed by the CDIO founders and interviewed to examine the efficacy of these degree programmes, particularly in this key objective. Graduate employment rates, self assessment of graduate attributes and examples of work produced by MEng graduates provided positive evidence that their capabilities met the requirements of the profession. The 24% questionnaire response rate from the 96 graduates to date did not however facilitate statistically significant conclusions to be drawn and particularly not for BEng graduates who were under represented in the response group. While not providing proof of efficacy the investigation did provide a good amount of useful data for consideration as part of a continuous improvement process.

Phosphorus Adsorption onto an Industrial Acidified Laterite By‒Product: Equilibrium and Thermodynamic Investigation

The present research investigates the uptake of phosphate ions from aqueous solutions using acidified laterite (ALS), a by-product from the production of ferric aluminium sulfate using laterite. Phosphate adsorption experiments were performed in batch systems to determine the amount of phosphate adsorbed as a function of solution pH, adsorbent dosage and thermodynamic parameters per fixed P concentration. Kinetic studies were also carried out to study the effect of adsorbent particle sizes. The maximum removal capacity of ALS observed at pH 5 was 3.68 mg P g^-1. It was found that as the adsorbent dosage increases, the equilibrium pH decreases, so an adsorbent dosage of 1.0 g L^-1 of ALS was selected. Adsorption capacity (q_m) calculated from the Langmuir isotherm was found to be 2.73 mg g^-1. Kinetic experimental data were mathematically well described using the pseudo first-order model over the full range of the adsorbent particle size. The adsorption reactions were endothermic, and the process of adsorption was favoured at high temperature; the ΔG and ΔH values implied that the main adsorption mechanism of P onto ALS is physisorption. The desorption studies indicated the need to consider a NaOH 0.1M solution as an optimal solution for practical regeneration applications.