Melt-compounded nanocomposites of titanium dioxide atomic-layer-deposition-coated polyamide and polystyrene powders

Polyamide and polystyrene particles were coated with titanium dioxide films by atomic layer deposition (ALD) and then melt-compounded to form polymer nanocomposites. The rheological properties of the ALD-created nanocomposite materials were characterized with a melt flow indexer, a melt flow spiral mould, and a rotational rheometer. The results suggest that the melt flow properties of polyamide nanocomposites were markedly better than those of pure polyamide and polystyrene nanocomposites. Such behavior was shown to originate in an uncontrollable decrease in the polyamide molecular weight, likely affected by a high thin-film impurity content, as shown in gel permeation chromatography (GPC) and scanning electron microscope (SEM) equipped with an energy-dispersive spectrometer. Transmission electron microscope image showed that a thin film grew on both studied polymer particles, and that subsequent melt-compounding was successful, producing well dispersed ribbon-like titanium dioxide with the titanium dioxide filler content ranging from 0.06 to 1.12wt%. Even though we used nanofillers with a high aspect ratio, they had only a minor effect on the tensile and flexural properties of the polystyrene nanocomposites. The mechanical behavior of polyamide nanocomposites was more complex because of the molecular weight degradation. Our approach here to form polymeric nanocomposites is one way to tailor ceramic nanofillers and form homogenous polymer nanocomposites with minimal work-related risks in handling powder form nanofillers. However, further research is needed to gauge the commercial potential of ALD-created nanocomposite materials. Copyright (C) 2011 John Wiley & Sons, Ltd.

Michel Foucault and Dorothy Smith in Case File Research: Strange Bedfellows or Complimentary Thinkers?

The aim of this article is to provide an exploration how the work of two theorists with notably different stances could be used effectively to enhance critical research methods in relation to the history of child welfare social work. The design and implementation of child welfare policies, practices and discourses could considerably benefit from a more historically well grounded scholarship that enables actors to connect their present concerns with the broader historical dynamics of social regulation. The article reports on how the work of Michel Foucault and Dorothy E. Smith might be considered in parallel as two different perspectives to the same scene in time and place. The differences and similarities in their approaches are explored with an emphasis on concepts most relevant to researching child welfare archives including discourse, text, the subject and power-knowledge. The article concludes with a commentary on further development to take forward this methodological analysis.

Characterization of Nickel Germanide Schottky Contacts for the Fabrication of Germanium p-channel MOSFETs

Nickel germanide Schottky contacts, formed by rapid thermal annealing of thin nickel films, have been characterized on n-type germanium wafers for a range of RTA temperatures. The highest Schottky barrier heights for electrons (= 0.6-0.7 eV) were obtained for RTA temperatures of approximately 300°C. For this RTA schedule, the corresponding barrier height for holes is close to zero, ideal for Schottky contacted p-channel germanium MOSFETs. When the RTA temperature was increased to 400oC, a dramatic reduction in electron barrier height (< 0.1 eV) was observed. This RTA schedule, therefore, appears ideal for ohmic source/drain contacts to n channel germanium MOSFETs. From sheet resistance measurements and XRD characterization, nickel germanide formation was found to occur at 300oC and above. The NiGe phase was dominant for RTA temperatures up to at least 435oC.

Precipitation, microstructure and mechanical properties of low nickel maraging steel

A maraging steel with a composition of Fe–12·94Ni–1·61Al–1·01Mo–0·23Nb (wt-%) was investigated. Optical, scanning electron and transmission electron microscopy and X-ray diffraction analysis were employed to study the microstructure of the steel after different aging periods at temperatures of 450–600°C. Hardness and Charpy impact toughness of the steel were measured. The study of microstructure and mechanical properties showed that nanosized precipitates were formed homogeneously during the aging process, which resulted in high hardness. As the aging time is prolonged, precipitates grow and hardness increases. Fractography of the as forged steel has shown mixed ductile and brittle fracture and has indicated that the steel has good toughness. Relationships among heat treatment, microstructure and mechanical properties are discussed. Further experiments using tensile testing and impact testing for aged steel were carried out.

Deformation of titanium alloy Ti-6Al-4V under dynamic compression

Deformation localisation is the main reason for material failure in cold forging of titanium alloys and is thus closely related to the production yield of cold forging. In the study of the influence of process parameters on dynamic compression, considering material constitutive behaviour, physical parameters and process parameters, a numerical dynamic compression model for titanium alloys has been constructed. By adjusting the process parameters, the severity of strain localisation and stress state in the localised zone can be controlled thus enhancing the compression performance of titanium alloys.

SEM-EDX of morphology of electroless nickel coatings with tin and tungsten

Electroless plating of binary Ni-P, ternary Ni-Sn-P and Ni-W-P, and quaternary Ni-W-Sn-P alloy coatings was carried out in alkalicitrate baths. After the plating, several kinds of test were carried out to determine the improvement in the characteristics and properties due to the additional elements as well as to study the change in behaviour when heat treatment was applied to these coatings. The coatings were subjected to X-ray diffraction analysis where it was found that all the coatings were amorphous. Interesting surface morphology features were examined using scanning electron microscopy. Addition of a third element improved the hardness.

Formation of nickel-thiolate aggregates via reaction with CH2Cl2

Reaction of the mononuclear nickel-thiolate complex [Ni(L-1)(dppe)] with CH2Cl2 affords the novel pentanuclear complex Ni5Cl2(L-1)(4)(dppe)(2)], while [Ni(L-1)(dcpe)] reacts with CH2Cl2 to give the binuclear species [Ni2Cl2(L-2)(dcpe)(2)] in which two L-1 units are linked by a methylene group derived from CH2Cl2.

Three-dimensional electron number densities in a titanium PLD plasma using interferometry

Interferometry has been used to investigate the spatio-temporal evolution of the electron number density in the initial stages of expansion following 248 nm ablation of a titanium target. Three-dimensional electron number densities are obtained from an interferogram of the plasma plume using the Abel inversion technique.

Microstructure and mechanical properties of low nickel maraging steel

Austenitization with lower temperature and intercritical annealing were introduced in the treatment of a maraging steel with a composition of Fe–12.94Ni–1.61Al–1.01Mo–0.23Nb (wt.%). Scanning electron microscopy was employed to study the microstructure after austenitization at 950 °C and intercritical annealing, followed by aging at 485 and 600 °C. X-ray diffraction (XRD) analysis was applied to evaluate the formation of retained or reverted austenite. Thermodynamic calculation was employed to calculate equilibrium phase mole fractions. Hardness and Charpy impact toughness of the steel were measured. Intercritical annealing treatments did not result in significant increase of hardness either before or after aging. The Charpy impact toughness of the alloy in aged condition was enhanced after austenitization at 950 °C. No austenite was observed in XRD. However, suspected reverted austenite was found after austenitization at 950 °C followed by aging at 600 °C for 4 h. Relationships among heat treatment, microstructure and mechanical properties are discussed.

Microscopy of heat treated titanium alloy BT16

Metallographic characterisation is combined with statistical analysis to study the microstructure of a BT16 titanium alloy after different heat treatment processes. It was found that the length, width and aspect ratio of α plates in this alloy follow the three-parameter Weibull distribution. Increasing annealing temperature or time causes the probability distribution of the length and the width of α plates to tend toward a normal distribution. The phase transformation temperature of the BT16 titanium alloy was found to be 875±5°C.