Alternative method to evaluate discharge coefficients. Part 2: case study

The purpose of this article is to apply an alternative method whereby discharge coefficients can be estimated for the flow through a poppet valve at various lifts. Presented is the development of an operational quasi-steady flow rig. An engine cylinder head poppet valve was used as the case study. The requirement to directly measure mass flowrates using a standard conventional steady flow apparatus has been eliminated. Transient mass flowrates, pressures and temperatures of air during an inflow test for a poppet valve at various lifts were measured. Mass flowrates were also calculated from measured cylinder gas pressures and corrected for heat transfer. Using both methods to determine the mass flowrates, isentropic discharge coefficients were calculated and shown to compare within +/- 4.0 per cent of steady flow data. A computational fluid dynamics (CFD) validation of the quasi-steady flow rig is also presented.

One Dimensional Modeling of a Turbogenerating Spark Ignition Engine Operating on Biogas

Turbocompounding is generally regarded as the process of recovering a proportion of the exhaust gas energy from a reciprocating engine and applying it to the output power of the crankshaft. In conventional turbocompounding, the power turbine has been mechanically connected to the crankshaft but now a new method has emerged. Recent advances in high speed electrical machines have enabled the power turbine to be coupled to an electric generator. Decoupling the power turbine from the crankshaft and coupling it to a generator allows the power electronics to control the turbine speed independently in order to optimize the turbine efficiency for different engine operating conditions.

Pre- to Post-discharge Behavior in Saline Solution

The development of a plasma discharge at low voltage (200-600 V) in saline solution is characterized using fast and standard CCD camera imaging. Vapor formation, plasma formation, and vapor collapse and subsequent pressure wave propagation are observed. If, with increasing voltage, the total energy deposited is kept approximately constant, the sequence and nature of events are similar but develop faster and more reproducibly at the higher voltages. This is attributed to the slower temporal evolution of the vapor layer at lower voltages which means a greater sensitivity to hydrodynamic instabilities at the vapor-liquid interface.

Asymptotic layer-type model of high pressure direct current glow discharge in electronegative gases

Here a self-consistent one-dimensional continuum model is presented for a narrow gap plane-parallel dc glow discharge. The governing equations consist of continuity and momentum equations for positive and negative ions and electrons coupled with Poisson's equation. A singular perturbation method is developed for the analysis of high pressure dc glow discharge. The kinetic processes of the ionization, electron attachment, and ion-ion recombination are included in the model. Explicit results are obtained for the asymptotic limits: delta=(r(D)/L)(2)--> 0, omega=(r(S)/L)(2)--> 0, where r(D) is the Debye radius, r(S) is recombination length, and L is the gap length. The discharge gap divides naturally into four layers with multiple space scales: anode fall region, positive column, transitional region, cathode fall region and diffusion layer adjacent to the cathode surface, its formation is discussed. The effects of the gas pressure, gap spacing and dc voltage on the electrical properties of the layers and its dimension are investigated. (C) 2000 American Institute of Physics. [S0021-8979(00)00813-6].

Asymptotic modeling of short plane-parallel high-pressure glow discharge

Here a self-consistent continuum model is presented for a narrow gap plane-parallel dc glow discharge. The set of governing equations consisting of continuity and momentum equations for positive ions, fast (emitted by the cathode) and slow electrons (generated by fast electron impact ionization) coupled with Poisson's equation is treated by the technique of matched asymptotic expansions. Explicit results are obtained in the asymptotic limit: (chi delta) much less than 1, where chi = e Phi(a)/kT, delta = (r(D)/L)(2) (Phi(a) is the applied voltage, r(D) is the Debye radius) and pL much greater than 1(Hg mm cm), where p is the gas pressure and L is the gap length. In the case of high pressure, the electron energy relaxation length is much smaller than the gap length, and so the local field approximation is valid. The discharge space divides naturally into a cathode fall sheath, a quasineutral plasma region, and an anode fall sheath. The electric potential distribution obtained for each region in a (semi)analytical form is asymptotically matched to the adjoining regions in the region of overlap. The effects of the gas pressure, gap length, and applied voltage on the length of each region are investigated. (C) 2000 American Institute of Physics. [S1070-664X(00)01302-1].

Role of low-energy electrons in Ar emission from low-pressure radio frequency discharge plasma

Optical emission spectra from a low-pressure Ar plasma were studied with high spatial resolution. It has been shown that the intensity ratios of Ar lines excited through metastable levels to those excited directly from the ground state are sensitive to the shape of electron energy distribution function. From these measurements, important information on the spatial variation of plasma parameters can be obtained. (C) 1999 American Institute of Physics. [S0003-6951(99)01629-0].

Comparison of plasma transport theory with measurements in a H- discharge

This paper and its companion paper describe the comparison between a one-dimensional theoretical model of a hydrogen discharge in a magnetic multipole plasma source and experimental measurements of the plasma parameters. The discharge chamber, described here, has been designed to produce significant densities of H- ions by incorporating a weak transverse field through the discharge to obtain electron cooling so as to maximize H- production. Langmuir probes are used to monitor the plasma, determining the ion density, the electron density and temperature and the plasma potential. The negative density is measured by photo-detachment of the extra electron using an intense laser beam. The model, described in the companion paper, uses the presented source geometry to calculate these plasma quantities as a function of the major are parameters; namely the are current and voltage and gas pressure. Good agreement is obtained between theory and experiment as a function of position and arc parameters.

TEMPORALLY AND SPATIALLY-RESOLVED PLASMA PARAMETERS AND EEDF MEASUREMENTS IN A LOW-FREQUENCY DISCHARGE

A time-resolved Langmuir probe technique is used to measure the dependence of the electron density, electron temperature, plasma potential and electron energy distribution function (EEDF) on the phase of the driving voltage in a RF driven parallel plate discharge. The measurements were made in a low-frequency (100-500 kHz), symmetrically driven, radio frequency discharge operating in H-2, D-2 and Ar at gas pressures of a few hundred millitorr. The EEDFs could not be represented by a single Maxwellian distribution and resembled the time averaged EEDFs reported in 13.56 MHz discharges. The measured parameters showed structure in their spatial and temporal dependence, generally consistent with a simple oscillating sheath model. Electron temperatures of less than 0.1 eV were measured during the phase of the RF cycle when both electrodes are negative with respect to the plasma.

STUDY OF THE DISCHARGE OF A MULTICUSP ION-SOURCE OPERATING WITH H2 AND D2

The plasma parameters and relative positive and negative ion concentrations in a small, filtered, multicusp ion source, operating at low plasma density (

TIME-RESOLVED ELECTRON-ENERGY DISTRIBUTION FUNCTION MEASUREMENTS IN A PULSED MAGNETIC MULTIPOLE HYDROGEN DISCHARGE

The time evolution of measured plasma parameters, including the electron energy distribution function (EEDF), in the discharge and post-discharge regime of a pulsed hydrogen magnetic multipole plasma is presented. The time necessary for the plasma to reach equilibrium has been established as 160-mu-s. The present results clarify the mechanisms which initiate the discharge. The decay rates of the charged-particle density and energy in the post-discharge have been measured. These measurements indicate that particle transport to the wall is the dominant loss mechanism for both charged-particle density and energy. The time-resolved EEDF is found to be non-Maxwellian in the discharge and Maxwellian in the late post-discharge.