Voltage scalable high-speed robust hybrid arithmetic units using adaptive clocking

In this paper, we explore various arithmetic units for possible use in high-speed, high-yield ALUs operated at scaled supply voltage with adaptive clock stretching. We demonstrate that careful logic optimization of the existing arithmetic units (to create hybrid units) indeed make them further amenable to supply voltage scaling. Such hybrid units result from mixing right amount of fast arithmetic into the slower ones. Simulations on different hybrid adder and multipliers in BPTM 70 nm technology show 18%-50% improvements in power compared to standard adders with only 2%-8% increase in die-area at iso-yield. These optimized datapath units can be used to construct voltage scalable robust ALUs that can operate at high clock frequency with minimal performance degradation due to occasional clock stretching. © 2009 IEEE.

High-Speed Fully Homomorphic Encryption Over the Integers

A fully homomorphic encryption (FHE) scheme is envisioned as a key cryptographic tool in building a secure and reliable cloud computing environment, as it allows arbitrary evaluation of a ciphertext without revealing the plaintext. However, existing FHE implementations remain impractical due to very high time and resource costs. To the authors’ knowledge, this paper presents the first hardware implementation of a full encryption primitive for FHE over the integers using FPGA technology. A large-integer multiplier architecture utilising Integer-FFT multiplication is proposed, and a large-integer Barrett modular reduction module is designed incorporating the proposed multiplier. The encryption primitive used in the integer-based FHE scheme is designed employing the proposed multiplier and modular reduction modules. The designs are verified using the Xilinx Virtex-7 FPGA platform. Experimental results show that a speed improvement factor of up to 44 is achievable for the hardware implementation of the FHE encryption scheme when compared to its corresponding software implementation. Moreover, performance analysis shows further speed improvements of the integer-based FHE encryption primitives may still be possible, for example through further optimisations or by targeting an ASIC platform.

High-speed conversion of xylose to l-lactate by electrodialysis bioprocess

Conversion of xylose to l-lactate was carried out by Lactococcus lactis IO-1 using an electrodialysis bioprocess (ED-BP). At 50 g l -1 xylose, the ED-BP was already complete in half the time (32 h) taken by the control culture without electrodialysis (>60 h). At 80 g l -1 xylose, the control culture was unable to consume >50 g l -1 xylose, whereas the ED-BP consumed 75 g l -1 xylose in 45 h. Thus, the simultaneous removal of lactate and acetate by ED-BP was associated with high-speed l-lactate production, increased xylose consumption and an increased l-lactate production. Copyright (C) 1998 Elsevier Science B.V.

In situ, high-resolution imaging of labile phosphorus in sediments of a large eutrophic lake

Understanding the labile status of phosphorus (P) in sediments is crucial for managing a eutrophic lake, but it is hindered by lacking in situ data particularly on a catchment scale. In this study, we for the first time characterized in situ labile P in sediments with the Zr-oxide diffusive gradients in thin films (Zr-oxide DGT) technique at a two-dimensional (2D), submillimeter resolution in a large eutrophic lake (Lake Taihu, China, with an area of 2338km²). The concentration of DGT-labile P in the sediment profiles showed strong variation mostly ranging from 0.01 to 0.35mgL^-1 with a considerable number of hotspots. The horizontal heterogeneity index of labile P varied from 0.04 to 4.5. High values appeared at the depths of 0-30mm, likely reflecting an active layer of labile P under the sediment-water interface (SWI). Concentration gradients of labile P were observed from the high-resolution 1D DGT profiles in both the sediment and overlying water layers close to the SWI. The apparent diffusion flux of P across the SWI was calculated between -21 and 65ngcm^-2d^-1, which showed that the sediments tended to be a source and sink of overlying water P in the algal- and macrophyte-dominated regions, respectively. The DGT-labile P in the 0-30mm active layer showed a better correlation with overlying water P than the labile P measured by ex situ chemical extraction methods. It implies that in situ, high-resolution profiling of labile P with DGT is a more reliable approach and will significantly extend our ability in in situ monitoring of the labile status of P in sediments in the field.

Very high speed 17 Gbps SHACAL encryption architecture

Very high speed and low area hardware architectures of the SHACAL-1 encryption algorithm are presented in this paper. The SHACAL algorithm was a submission to the New European Schemes for Signatures, Integrity and Encryption (NESSIE) project and it is based on the SHA-1 hash algorithm. To date, there have been no performance metrics published on hardware implementations of this algorithm. A fully pipelined SHACAL-1 encryption architecture is described in this paper and when implemented on a Virtex-II X2V4000 FPGA device, it runs at a throughput of 17 Gbps. A fully pipelined decryption architecture achieves a speed of 13 Gbps when implemented on the same device. In addition, iterative architectures of the algorithm are presented. The SHACAL-1 decryption algorithm is derived and also presented in this paper, since it was not provided in the submission to NESSIE. © Springer-Verlag Berlin Heidelberg 2003.

Per-Flow State Management Technique for High-Speed Networks

Flow processing is a fundamental element of stateful traffic classification and it has been recognized as an essential factor for delivering today’s application-aware network operations and security services. The basic function within a flow processing engine is to search and maintain a flow table, create new flow entries if no entry matches and associate each entry with flow states and actions for future queries. Network state information on a per-flow basis must be managed in an efficient way to enable Ethernet frame transmissions at 40 Gbit/s (Gbps) and 100 Gbps in the near future. This paper presents a hardware solution of flow state management for implementing large-scale flow tables on popular computer memories using DDR3 SDRAMs. Working with a dedicated flow lookup table at over 90 million lookups per second, the proposed system is able to manage 512-bit state information at run time.

Novel precipitated zirconia-based DGT technique for high-resolution imaging of oxyanions in waters and sediments

Water-sediment exchange is a fundamental component of oxyanion cycling in the environment. Yet, many of the (im)mobilization processes overlay complex spatial and temporal redox regimes that occur within millimeters of the interface. Only a few methods exist that can reliably capture these porewater fluxes, with the most popular being high-resolution diffusive gradients in thin films (HR-DGT). However, functionality of HR-DGT is restricted by the availability of suitable analyte binding agents within the sampler, which must be simple to cast and homogeneously distributed in the binding layer, exhibit adequate sorption capacities, be resistive to chemical change, and possess a very fine particle size (≤10 μm). A novel binding layer was synthesized to meet these requirements by in situ precipitation of zirconia into a precast hydrogel. The particle diameter ≤0.2 μm of zirconia in this precipitated gel was uniform and at least 50-times smaller than the conventional molding approach. Further, this gel had superior binding and stability characteristics compared with the commonly used ferrihydrite HR-DGT technique and could be easily fabricated as an ultrathin gel (60 μm) for simultaneous oxygen imaging in conjunction with planar-optodes. Chemical imaging of anion and oxygen fluxes using the new sampler were evaluated on Lake Taihu sediments.

The Use of High Surface Area Silica and Supercritical Carbon Dioxide to Enhance Solubility of Poorly Water-Soluble Drugs

Purpose Poor water-solubility of BCS class II drugs can limit their commercialization because of reduced oral bioavailability. It has been reported that loading of drug by adsorption onto porous silica would enhance drug solubility due to the increased surface area available for solvent diffusion. In this work, solid dispersions are formed using supercritical carbon dioxide (scCO2). The aim of this research was to characterise the solid-state properties of scCO2 dispersion and to investigate the impact of altering scCO2 processing conditions on final amorphous product performance that could lead to enhancement of drug dissolution rate for BCS class II drugs. Methods Indomethacin (IND) was purchased from Sigma-Aldrich (Dorset, UK) and was used as a model drug with two grades of high surface area silica (average particle sizes 3&[micro] and 7&[micro]), which were obtained directly from Grace-Davison (Germany). Material crystallinity was evaluated using powder X-ray diffraction (PXRD, Rigaku™, miniflex II, Japan) and high-speed differential scanning calorimetry (Hyper-DSC 8000, Perkin Elmer, USA). Materials were placed in a high-pressure vessel consisting of a CO2 cylinder, a Thar™ Technologies P50 high-pressure pump and a 750 ml high-pressure vessel (Thar, USA). Physical mixtures were exposed to CO2 gas above its critical conditions. SEM imaging and elemental analysis were conducted using a Jeol 6500 FEGSEM (Advanced MicroBeam Inc., Austria). Drug release was examined using USP type II dissolution tester (Caleva™, UK). Results The two grades of silica were found to be amorphous using PXRD and Hyper-DSC. Using PXRD, it was shown that an increase in incubation time and pressure resulted in a decrease in the crystalline content. Drug release profiles from the two different silica formulations prepared under the same conditions are shown in Figure 1. It was found that there was a significant enhancement in drug release, which was influenced, by silica type and other experiment conditions such as temperature, pressure and exposure time. SEM imaging and elemental analysis showed drug deposited inside silica pores as well as on the outer surface. Conclusion This project has shown that silica carrier platforms may be used as an alternative approach to generating polymeric solid dispersions of amorphous drugs exhibiting enhanced solubility.

Speed tuning of direction repulsion describes an inverted U-function

Direction repulsion describes the phenomenon in which observers typically overestimate the direction difference between two superimposed motions moving in different directions (Marshak & Sekuler, Science 205(1979) 1399). Previous research has found that, when a relatively narrow range of distractor speeds is considered, direction repulsion of a target motion increases monotonically with increasing speed of the distractor motion. We sought to obtain a more complete measurement of this speed-tuning function by considering a wider range of distractor speeds than has previously been used. Our results show that, contrary to previous reports, direction repulsion as a function of distractor speed describes an inverted U-function. For a target of 2.5deg/s, we demonstrate that the attenuation of repulsion magnitude with high-speed disractors can be largely explained in terms of the reduced apparent contrast of the distractor. However, when we reduce target motion speed, this no longer holds. When considered from the perspective of Edwards et al.s (Edwards, Badcock, & Smith, Vision Research 38 (1998) 1573) two global-motion channels, our results suggest that direction repulsion is speed dependent when the distractor and target motions are processed by different globalmotion channels, but is not speed dependent when both motions are processed by the same, high-speed channel. The implications of these results for models of direction repulsion are discussed.

Calcium signaling in ocular arterioles

Local control of blood flow to the photoreceptors and associated neurons in the retina is largely achieved through changes in tone within the choroidal and retinal arterioles. This is primarily achieved through changes in [Ca2+] within the smooth muscle of these vessels, which regulates cell contraction and vascular constriction. Here we review some aspects of the cell physiology involved in these Ca2+-signaling processes, with particular emphasis on the molecular mechanisms involved. Ca2+-influx across the plasma membrane can occur via a variety of Ca2+-channels, including voltage-operated, store-operated, and receptor-operated channels. Ca2+ may also be released from intracellular stores via RyR-, or IP3R-gated channels in the SR membrane. Using high-speed confocal Ca2+-imaging, we have also demonstrated that the resulting signals are far from homogeneous, with spontaneous activity in retinal arterioles being characterized by both localized Ca2+-sparks and more global Ca2+-waves and oscillations. These signals may be specifically and differentially targeted, for example, to Ca2+-sensitive ion channels (stimulus-excitation coupling), or pathways regulating contraction (stimulus-contraction coupling). Exploring the role of changes in such targeting in disease states will provide exciting opportunities for future research.

Ultracam - An Ultra-Fast Triple-Beam CCD Camera

ULTRACAM is a high-speed three-colour CCD camera designed to provide imaging photometry at high temporal resolutions. The instrument is highly portable and will be used at a number of large telescopes around the world. ULTRACAM was successfully commissioned on the 4.2-m William Herschel Telescope on La Palma on 16 May 2002 over 3 months ahead of schedule and within budget. The instrument was funded by PPARC and designed and built by a consortium involving the Universities of Sheffield Southampton and the UKATC Edinburgh. We present an overview of the design and performance characteristics of ULTRACAM and highlight some of its most recent scientific results.

Electromagnetic Focusing and Imaging in Stratified Media Using Gradient Phase Profiled Conjugating Lens

High-resolution imaging of a dipole source in stratified medium based on negative refraction is presented in this paper. Compensation of the material parameter contrast at the stratified media interface is achieved using a gradient phase profiled conjugating lens (GPCL). It is shown both analytically and numerically that the phase gradient applied across the GPCL positioned at the interface of vertically stratified media enables a high-quality image of a dipole source in a mirror symmetric position with respect to the lens plane. The analytical closed form expression of the phase gradient function is derived using Huygens-Kirchhoff principle. The result is applicable to media with arbitrary stratification and material parameters, including lossy materials. The mechanism for formation of the dipole image in the stratified medium and aberration due to the dielectric contrast at the interface, particularly electromagnetic loss, is discussed in detail. The efficacy of gradient phase and amplitude aberration compensations mechanisms available through the GPCL is articulated. The results of the study are of importance in a wide range of imaging problems in stratified media for medical, civil, and military applications.

The Dynamics of Rapid Redshifted and Blueshifted Excursions in the Solar Hα Line

We analyze high temporal and spatial resolution time-series of spectralscans of the Hα line obtained with the CRisp Imaging SpectroPolarimeter instrument mounted on the Swedish Solar Telescope.The data reveal highly dynamic, dark, short-lived structures known asRapid Redshifted and Blueshifted Excursions (RREs, RBEs) that areon-disk absorption features observed in the red and blue wings ofspectral lines formed in the chromosphere. We study the dynamics of RREsand RBEs by tracking their evolution in space and time, measuring thespeed of the apparent motion, line of sight (LOS) Doppler velocity, andtransverse velocity of individual structures. A statistical study oftheir measured properties shows that RREs and RBEs have similaroccurrence rates, lifetimes, lengths, and widths. They also displaynon-periodic, nonlinear transverse motions perpendicular to their axesat speeds of 4-31 km s-1. Furthermore, both typesof structures either appear as high speed jets and blobs that aredirected outwardly from a magnetic bright point with speeds of50-150 km s-1, or emerge within a few seconds. Astudy of the different velocity components suggests that the transversemotions along the LOS of the chromospheric flux tubes are responsiblefor the formation and appearance of these redshifted/blueshiftedstructures. The short lifetime and fast disappearance of the RREs/RBEssuggests that, similar to type II spicules, they are rapidly heated totransition region or even coronal temperatures. We speculate that theKelvin-Helmholtz instability triggered by observed transversemotions of these structures may be a viable mechanism for their heating.

Nanohole arrays enable multiple-point-source imaging

A new type of focal-palne array made of a nanoscale metal screen mimics the function of a lens, focuses light (and plasmons) into subwavelength hot spots, and achieves high-resolution imaging of complex sources.