Teaching and Learning Guide for 'Modern Problems of Editing...'

Companion piece to my earlier article in Literature Conmpass: 'Modern Problems of Editing: The Two Texts of Doctor Faustus'. Provides a model for a module based on the topic of that article.

Barrier height variations and interface properties of PtSi/Si structures

To study some of the interfacial properties of PtSi/Si diodes, Schottky structures were fabricated on (100) crystalline silicon substrates by conventional thermal evaporation of Pt on Si followed by annealing at different temperatures (from 400 degrees C to 700 degrees C) to form PtSi. The PtSi/n-Si diodes, all yielded Schottky barrier (SB) heights that are remarkably temperature dependent. The temperature range (20-290 K) over which the I-V characteristics were measured in the present study is broader with a much lower limit (20 K), than what is usually reported in literature. These variations in the barrier height are adequately interpreted by introducing spatial inhomogeneity into the barrier potential with a Gaussian distribution having a mean barrier of 0.76 eV and a standard deviation of 30 meV. Multi-frequency capacitance-voltage measurements suggest that the barrier is primarily controlled by the properties of the silicide-silicon interface. The forward C-V characteristics, in particular, show small peaks at low frequencies that can be ascribed to interface states rather than to a series resistance effect.

Oxidized Recombinant Human Growth Hormone That Maintains Conformational Integrity

Chemical degradations often induce changes in protein conformation and thus influence protein activity and protein stability in solutions. One difficulty in studying of chemical degradations on protein aqueous properties is to obtain sufficient amount of chemically degraded protein which is well characterized. Chemical degradation protocols that are often used may induce also conformation changes and aggregation of the protein. In this article we studied the effect of methionine oxidation on the conformation of recombinant human growth hormone (r-hGH). In literature it is reported that oxidation of methionine residues induces conformation changes on r-hGH. In our study, oxidation of r-hGH was performed by incubation with hydrogen peroxide under mild conditions. Mass spectrometry and chromatographic analysis revealed that oxidation with hydrogen peroxide resulted in more than 90% of oxidized r-hGH. By extensive spectroscopic characterizations no detectable change in conformation and aggregation of r-hGH after oxidation was found. In conclusion, mild oxidation conditions led to selective oxidation of the two more accessible methionine residues of r-hGH (Met(14) and Met(125)) and did not results in any conformation change of the protein. These findings prove that oxidation of human growth hormone does not influence protein conformation and demonstrate the importance of employing mild conditions during production of oxidized protein. (C) 2010 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 100:110-122, 2011

JPEG encoder system-on-a-chip demonstrator

The design of a System-on-a-Chip (SoC) demonstrator for a baseline JPEG encoder core is presented. This combines a highly optimized Discrete Cosine Transform (DCT) and quantization unit with an entropy coder which has been realized using off-the-shelf synthesizable IP cores (Run-length coder, Huffman coder and data packer). When synthesized in a 0.35 µm CMOS process, the core can operate at speeds up to 100 MHz and contains 50 k gates plus 11.5 kbits of RAM. This is approximately 20% less than similar JPEG encoder designs reported in literature. When targeted at FPGA the core can operate up to 30 MHz and is capable of compressing 9-bit full-frame color input data at NTSC or PAL rates.

Horizontal Descemet's membrane break due to birth trauma

We report an unusual case of horizontal corneal Descemet's membrane break due to birth trauma. The patient had a difficult birth with trauma to her right eye and poor vision. However unlike the reports in literature, which describe these breaks to have a characteristic vertical or vertically oblique orientation in birth trauma, the breaks in our patient were horizontal. No other cause was found for these Descemet's breaks.

Effect of impeller speed on mechanical and dissolution properties of high-shear granules

Impeller speed is one of the most crucial process variables that affect the properties of the granules produced in a high-shear granulator. Several reports can be found in literature that discuss the influence of impeller speed on the granules size. For instance some researchers like Knight report an increase of granule size with impeller speed [1] and [2], while others (Scheaefer et al. and Ramaker et al.) observed a decrease of granules size with increasing impeller speed [3] and [4]. However there is limited work reported in literature on the effect of the impeller speed on the mechanical properties of granules. Mechanical properties are important as they affect the performance of the granules on the other downstream process such as transportation and handling. The work reported here serves to address the missing in knowledge gap regarding the influence of impeller speed on mechanical properties granules. How the granulation system responds to the changes in the impeller speeds depends on binder that is used in the process. For this reason the two extreme cases, of a low viscosity binder system and high viscosity binder system are considered in this research. For low viscosity binder system it was observed that the granule size decreased with increasing impeller speed whilst for the high viscosity binder system the opposite was observed by Knight [1]. The granule strength, the Young's modulus and yield strength of the high viscosity granules increased with increasing impeller speed where as the opposite trends were observed for the low viscosity binder granules.

Detailed validation of an automotive catalysis model using spatially resolved measurements within the catalyst substrate

Many kinetic models have appeared in literature in past decades using two main approaches: the traditional global kinetics approach, or the more complex micro-kinetics approach. Whether global or micro-kinetics, kinetic models have been based on experimental data obtained at the end of the monolith. The experimental procedure using end pipe analysis may give an accurate overview of the reaction mechanisms that occur; however, the lack of information from within the catalyst can ultimately lead to inaccuracies in the kinetic model and parameters used.

Using SpaciMS, a spatially resolved experimental technique developed at the Queen's University Belfast, information from within the catalyst can be obtained. This minimally invasive technique provides detailed information of the gas concentration and temperature profile from inside the catalytic monolith. This paper presents a kinetic model and simulations validated against experimental data obtained from three positions inside the catalyst monolith at 2, 14, and 26 mm in, using data from the SpaciMS. Also, simulations of end pipe analysis, using a commercial reactor, for the CO oxidation are presented and analyzed. The simulations presented are for varying concentrations of both CO and O2 (0.5 % and 1 % CO, 0.5 % and 2 % O2) for both the global and micro-kinetic approach.

Accounting for clean, fast and high yielding reactions under microwave conditions

Thermal reactions proceed optimally when they are rapidly heated to the highest tolerable temperature, held there for the shortest possible time and then quenched. This is explained through assessments of reaction kinetics in literature examples and models. Although presently available microwave equipment is better suited to rapid heating than resistance-heated systems, the findings do not depend upon the method of heating. Claims that microwave heated reactions proceed faster and more cleanly than their conventionally heated counterparts are valid only when comparably rapid heating and cooling cannot be obtained by conventional heating. These findings suggest that rigid adherence to the sixth principle of green chemistry, relating to the use of ambient temperature and pressure, may not always afford optimal results. © 2010 The Royal Society of Chemistry.

An Evaluation of 1D Loss Model Collections for the Off-Design Performance Prediction of an Automotive Turbocharger Compressor

Abstract. Single-zone modelling is used to assess different collections of impeller 1D loss models. Three collections of loss models have been identified in literature, and the background to each of these collections is discussed. Each collection is evaluated using three modern automotive turbocharger style centrifugal compressors; comparisons of performance for each of the collections are made. An empirical data set taken from standard hot gas stand tests for each turbocharger is used as a baseline for comparison. Compressor range is predicted in this study; impeller diffusion ratio is shown to be a useful method of predicting compressor surge in 1D, and choke is predicted using basic compressible flow theory. The compressor designer can use this as a guide to identify the most compatible collection of losses for turbocharger compressor design applications. The analysis indicates the most appropriate collection for the design of automotive turbocharger centrifugal compressors.

Finite Element Analysis of the Enhanced Strength of Laterally Restrained RC Slabs

This paper presents the numerical simulation of the ultimate behaviour of 85 one-way and two-way spanning laterally restrained concrete slabs of variable thickness, span, reinforcement ratio, strength and boundary conditions reported in literature by different authors. The developed numerical model was described and all the assumptions were illustrated. ABAQUS, a Finite Element Analysis suite of software, was employed. Non-linear implicit static general analysis method offered by ABAQUS was used. Other analysis methods were also discussed in general in terms of application such as Explicit Dynamic Analysis and Riks method. The aim is to demonstrate the ability and efficacy of FEA to simulate the ultimate load behaviour of slabs considering different material properties and boundary conditions. The authors intended to present a numerical model that provides consistent predictions of the ultimate behaviour of laterally restrained slabs that could be used as an alternative for expensive real life testing as well as for the design and assessment of new and existing structures respectively. The enhanced strength of laterally-restrained slabs compared with conventional design methods predictions is believed to be due to compressive membrane action (CMA). CMA is an inherent phenomenon of laterally restrained concrete beams/slabs. The numerical predictions obtained from the developed model were in good correlation with the experimental results and with those obtained from the CMA method developed at the Queen’s University Belfast, UK.

Operators for Similarity Search: Semantics, Techniques and Usage Scenarios

This book provides a comprehensive tutorial on similarity operators. The authors systematically survey the set of similarity operators, primarily focusing on their semantics, while also touching upon mechanisms for processing them effectively.

The book starts off by providing introductory material on similarity search systems, highlighting the central role of similarity operators in such systems. This is followed by a systematic categorized overview of the variety of similarity operators that have been proposed in literature over the last two decades, including advanced operators such as RkNN, Reverse k-Ranks, Skyline k-Groups and K-N-Match. Since indexing is a core technology in the practical implementation of similarity operators, various indexing mechanisms are summarized. Finally, current research challenges are outlined, so as to enable interested readers to identify potential directions for future investigations.

In summary, this book offers a comprehensive overview of the field of similarity search operators, allowing readers to understand the area of similarity operators as it stands today, and in addition providing them with the background needed to understand recent novel approaches.

A novel TRNSYS type for short-term borehole heat exchanger simulation: B2G model

Models of ground source heat pump (GSHP) systems are used as an aid for the correct design and optimization of the system. For this purpose, it is necessary to develop models which correctly reproduce the dynamic thermal behavior of each component in a short-term basis. Since the borehole heat exchanger (BHE) is one of the main components, special attention should be paid to ensuring a good accuracy on the prediction of the short-term response of the boreholes. The BHE models found in literature which are suitable for short-term simulations usually present high computational costs. In this work, a novel TRNSYS type implementing a borehole-to-ground (B2G) model, developed for modeling the short-term dynamic performance of a BHE with low computational cost, is presented. The model has been validated against experimental data from a GSHP system located at Universitat Politècnica de València, Spain. Validation results show the ability of the model to reproduce the short-term behavior of the borehole, both for a step-test and under normal operating conditions.

Sustainable non-automotive vehicles: The simulation challenges

Simulation is a well-established and effective approach to the development of fuel-efficient and low-emissions vehicles in both on-highway and off-highway applications.

The simulation of on-highway automotive vehicles is widely reported in literature, whereas research relating to non-automotive and off-highway vehicles is relatively sparse. This review paper focuses on the challenges of simulating such vehicles and discusses the differences in the approach to drive cycle testing and experimental validation of vehicle simulations. In particular, an inner-city diesel-electric hybrid bus and an ICE (Internal Combustion Engine) powered forklift truck will be used as case studies.

Computer prediction of fuel consumption and emissions of automotive vehicles on standardised drive cycles is well-established and commercial software packages such as AVL CRUISE have been specifically developed for this purpose. The vehicles considered in this review paper present new challenges from both the simulation and drive-cycle testing perspectives. For example, in the case of the forklift truck, the drive cycles involve reversing elements, variable mass, lifting operations, and do not specify a precise velocity-time profile. In particular, the difficulties associated with the prediction of productivity, i.e. the maximum rate of completing a series of defined operations, are discussed. In the case of the hybrid bus, the standardised drive cycles are unrepresentative of real-life use and alternative approaches are required in the development of efficient and low-emission vehicles.

Two simulation approaches are reviewed: the adaptation of a standard automotive vehicle simulation package, and the development of bespoke models using packages such as MATLAB/Simulink.