Toward Self-Assembled Ferroelectric Random Access Memories: Hard-Wired Switching Capacitor Arrays with Almost Tb/in.2 Densities

We report on the successful fabrication of arrays of switchable nanocapacitors made by harnessing the self-assembly of materials. The structures are composed of arrays of 20-40 nm diameter Pt nanowires, spaced 50-100 nm apart, electrodeposited through nanoporous alumina onto a thin film lower electrode on a silicon wafer. A thin film ferroelectric (both barium titanate (BTO) and lead zirconium titanate (PZT)) has been deposited on top of the nanowire array, followed by the deposition of thin film upper electrodes. The PZT nanocapacitors exhibit hysteresis loops with substantial remnant polarizations, while although the switching performance was inferior, the low-field characteristics of the BTO nanocapacitors show dielectric behavior comparable to conventional thin film heterostructures. While registration is not sufficient for commercial RAM production, this is nevertheless an embryonic form of the highest density hard-wired FRAM capacitor array reported to date and compares favorably with atomic force microscopy read-write densities.

The effect of tungsten trioxide thin films at ferroelectric-electrode boundaries on fatigue behaviour

A conventional thin film capacitor heterostructure, consisting of sol-gel deposited lead zirconium titanate (PZT) layers with sputtered platinum top and bottom electrodes, was subjected to fatiguing pulses at a variety of frequencies. The fatigue characteristics were compared to those of a similarly processed capacitor in which a ~20nm tungsten trioxide layer had been deposited, using pulsed laser deposition, between the ferroelectric and upper electrode. The expectation was that, because of its ability to accommodate considerable oxygen non-stoichiometry, tungsten trioxide (WO3) might act as an efficient sink for any oxygen vacancies flushed to the electrode-ferroelectric boundary layer during repetitive switching, and hence would improve the fatigue characteristics of the thin film capacitor. However, it was found that, in general, the addition of tungsten trioxide actually increases the rate of fatigue. It appears that any potential benefit from the WO3, in terms of absorbing oxygen vacancies, is far outweighed by it causing dramatically increased charge injection in the system.

Nanoscale ferroelectrics machined from single crystals

This paper summarises some of the most recent work that has been done on nanoscale ferroelectrics as a result of a joint collaborative research effort involving groups in Queen's University Belfast, the University of Cambridge and the University of St. Andrews. Attempts have been made to observe fundamental effects of reduced size, and increasing morphological complexity, on ferroelectric behaviour by studying the functional response and domain characteristics in nanoscale single crystal material, whose size and morphology have been defined by Focused Ion Beam (FIB) patterning. This approach to nanoshape fabrication has allowed the following broad statements to be made: (i) in single crystal BaTiO3 sheets, permittivity and phase transition behaviour is not altered from that of bulk material down to a thickness of similar to 75 nm; (ii) in single crystal BaTiO3 sheets and nanowires changes in observed domain morphologies are consistent with large scale continuum modeling.

Size Effects on Thin Film Ferroelectrics: Experiments on Isolated Single Crystal Sheets

Thin lamellae were cut from bulk single crystal BaTiO3 using a Focused Ion Beam Microscope. They were then removed and transferred onto single crystal MgO substrates, so that their functional properties could be measured independent of the original host bulk ferroelectric. The temperature dependence of the capacitance of these isolated single crystal films was found to be strongly bulk-like, demonstrating a sharp Curie anomaly, as well as Curie-Weiss behaviour. In addition, the sudden change in the remanent polarisation as a function of temperature at TC was characteristic of a first order phase change. The work represents a dramatic improvement on that previously published by M. M. Saad, P. Baxter, R. M. Bowman, J. M. Gregg, F. D. Morrison & J. F. Scott, J. Phys: Cond. Matt., 16 L451-L456 (2004), as critical shortcomings in the original specimen geometry, involving potential signal contributions from bulk BaTiO3, have now been obviated. That the functional properties of single crystal thin film lamellae are comparable to bulk, and not like those of conventionally deposited heteroegenous thin film systems, has therefore been confirmed.

Insight into why the Langmuir-Hinshelwood mechanism is generally preferred

In heterogeneous catalysis, the two main reaction mechanisms which have been proposed are the Langmuir-Hinshelwood and the Eley-Rideal. For the vast majority of surface catalytic reactions, it has been accepted that the Langmuir-Hinshelwood mechanism is preferred. In this study, we investigate catalytic CO oxidation on Pt(111). It is found that reaction barriers for Langmuir-Hinshelwood mechanisms actually tend to be higher than those for Eley-Rideal ones. An explanation is presented as to why it is still more probable for the reaction to proceed via the Langmuir-Hinshelwood mechanism, despite its higher reaction barrier. (C) 2002 American Institute of Physics.

A density functional theory study of carbon monoxide oxidation on the Cu3Pt(111) alloy surface: Comparison with the reactions on Pt(111) and Cu(111)

Alloying metals is often used as an effective way to enhance the reactivity of surfaces. Aiming to shed light on the effect of alloying on reaction mechanisms, we carry out a comparative study of CO oxidation on Cu3Pt(111), Pt(111), and Cu(111) by means of density functional theory calculations. Alloying effects on the bonding sites and bonding energies of adsorbates, and the reaction pathways are investigated. It is shown that CO preferentially adsorbs on an atop site of Pt and O preferentially adsorbs on a fcc hollow site of three Cu atoms on Cu3Pt(111). It is also found that the adsorption energies of CO (or O-a) decreases on Pt (or Cu) on the alloy surface with respect to those on pure metals. More importantly, having identified the transition states for CO oxidation on those three surfaces, we found an interesting trend for the reaction barrier on the three surfaces. Similar to the adsorption energies, the reaction barrier on Cu3Pt possesses an intermediate value of those on pure Pt and Cu metals. The physical origin of these results has been analyzed in detail. (C) 2001 American Institute of Physics.