Natural inspiration for self-adaptive systems

The emergent behaviour of autonomic systems, together with the scale of their deployment, impedes prediction of the full range of configuration and failure scenarios; thus it is not possible to devise management and recovery strategies to cover all possible outcomes. One solution to this problem is to embed self-managing and self-healing abilities into such applications. Traditional design approaches favour determinism, even when unnecessary. This can lead to conflicts between the non-functional requirements. Natural systems such as ant colonies have evolved cooperative, finely tuned emergent behaviours which allow the colonies to function at very large scale and to be very robust, although non-deterministic. Simple pheromone-exchange communication systems are highly efficient and are a major contribution to their success. This paper proposes that we look to natural systems for inspiration when designing architecture and communications strategies, and presents an election algorithm which encapsulates non-deterministic behaviour to achieve high scalability, robustness and stability.

Advanced microwave oven for rapid curing of encapsulant

The curing of a thermosetting polymer materials utilized on micro-electronics packaging applications can be performed using microwave systems. The use of microwave energy enables the cure process to be completed more rapidly than with alternative approaches due to the ability to heat volumetrically. Furthermore, advanced dual-section microwave systems enable curing of individual components on a chip-on-board assembly. The dielectric properties of thermosetting polymer materials, commonly used in microelectronics packaging applications, vary significantly with temperature and degree of cure. The heating rate within a material subjected to an electric field is primarily dependant on the dielectric loss properties of the material itself. This article examines the variation in dielectric properties of a commercially available encapsulant paste with frequency and temperature and the resulting influence on the cure process. The 'FAMOBS' dual section microwave system and its application to microelectronics manufacture are described. The measurement of the dielectric properties of 'Henkel EO1080' encapsulant paste uses a commercially available 'dielectric probe kit' and is described in this paper. The FAMOBS heating system is used to encapsulate a small op-amp chip. A numerical model formulated to assess the cure process in thermosetting polymer materials under microwave heating is outlined. Numerical results showing that the microwave processing systems is capable of rapidly and evenly curing thermosetting polymer materials are presented.

Radio propagation modeling for capacity optimization in wireless relay MIMO systems with partial CSI

The enormous growth of wireless communication systems makes it important to evaluate the capacity of such channels. Multiple Input Multiple Output (MIMO) wireless communication systems are shown to yield significant performance improvement to data rates when compared to the traditional Single Input Single Output (SISO) wireless systems. The benefits of multiple antenna elements at the transmitter and receiver have become necessary to the research and the development of the next generation of mobile communication systems. In this paper we propose the use of Relaying MIMO wireless communication systems for use over long throughput. We investigate how Relays can be used in a "demodulate-and-forward" operation when the transmitter is equipped with spatially correlated multiple antenna elements and the receiver has only partial knowledge of the statistics of the channel. We show that Relays between the source and destination nodes of a wireless communication system in MIMO configuration improve the throughput of the system when compared to the typical MIMO systems, or achieve the desired channel capacity with significantly lower power resources needed.

Adaptive ordering for imperfect successive decision feedback multiuser detection

A method for selecting the order in which the users are detected in communication systems employing adaptive successive decision feedback multiuser detection is proposed. Systems employing channel coding without the assumption of perfect decision feedback are analyzed. The method is based on the mean squared error (MSE) measurements during a training period for each user. The analysis' shows that the method delivers BER performance improvement relative to other previously proposed ordering methods

Coupled FDTD-FVM simulation of microwave heating of polymer materials for micro-systems packaging applications

Heating in an idealised polymer load in a novel open-ended variable frequency microwave oven is numerically simulated using a couple solver approach. The frequency-agile microwave oven bonding system (FAMOBS)is developed to meet rapid polymer curing requirements in microelectronics and optoelectronics manufacturing. The heating of and idealised polymer load has been investigated through numerical modelling. Assessment of the system comprises of simulation of electromagnetic fields and of temperature distribution within the load. Initial simulation results are presented and contrasted with experimental analysis of field distribution

Comparison of encapsulant curing with convention and microwave systems

Comparison of the performance of a conventional convection oven system with a dual-section microwave system for curing thermosetting polymer encapsulant materials has been performed numerically. A numerical model capable of analysing both the convection and microwave cure processes has been developed and is breifly outliines. The model is used to analyse the curing of a commercially available encapsulant material using both systems. Results obtained from numerical solutions are presented, confirming that the VFM system enables the cure process to be carried out far more rapidly than with the convection oven system. This capability stems from the fundamental heating processes involved, namely that microwave processing enables the heating rate to be varied independently of the material temperature. Variations in cure times, curing rates, maximum temperatures and residual stresses between the processes are fully discussed.