A life cycle model for product-service systems design

Western manufacturing companies are developing innovative ways of delivering value that competes with the low cost paradigm. One such strategy is to deliver not only products, but systems that are closely aligned with the customer value proposition. These systems are comprised of integrated products and services, and are referred to as Product-Service Systems (PSS). A key challenge in PSS is supporting the design activity. In one sense, PSS design is a further extension of concurrent engineering that requires front-end input from the additional downstream sources of product service and maintenance. However, simply developing products and service packages is not sufficient: the new design challenge is the integrated system. This paper describes the development of a PSS data structure that can support this integrated design activity. The data structure is implemented in a knowledge base using the Protégé knowledge base editor.

Estimating the flow rate capacity of an overturned rail carriage end exit in the presence of smoke

While incidents requiring the rapid egress of passengers from trains are infrequent, perhaps the most challenging scenario for passengers involves the evacuation from an overturned carriage subjected to fire. In this paper we attempt to estimate the flow rate capacity of an overturned rail carriage end exit. This was achieved through two full-scale evacuation experiments, in one of which the participants were subjected to non-toxic smoke. The experiments were conducted as part of a pilot study into evacuation from rail carriages. In reviewing the experimental results, it should be noted that only a single run of each trial was undertaken with a limited — though varied — population. As a result it is not possible to test the statistical significance of the evacuation times quoted and so the results should be treated as indicative rather than definitive. The carriage used in the experiments was a standard class Mark IID which, while an old carriage design, shares many features with those carriages commonly found on the British rail network. In the evacuation involving smoke, the carriage end exit was found to achieve an average flow rate capacity of approximately 5.0 persons/min. The average flow rate capacity of the exit without smoke was found to be approximately 9.2 persons/min. It was noted that the presence of smoke tended to reduce significantly the exit flow rate. Due to the nature of the experimental conditions, these flow rates are considered optimistic. Finally, the authors make several recommendations for improving survivability in rail accidents. Copyright © 2000 John Wiley & Sons, Ltd.

Numerical algorithms for modelling electrodeposition: Tracking the deposition front under forced convection from megasonic agitation

Electrodeposition is a widely used technique for the fabrication of high aspect ratio microstructures. In recent years, much research has been focused within this area aiming to understand the physics behind the filling of high aspect ratio vias and trenches on substrates and in particular how they can be made without the formation of voids in the deposited material. This paper reports on the fundamental work towards the advancement of numerical algorithms that can predict the electrodeposition process in micron scaled features. Two different numerical approaches have been developed, which capture the motion of the deposition interface and 2-D simulations are presented for both methods under two deposition regimes: those where surface kinetics is governed by Ohm’s law and the Butler–Volmer equation, respectively. In the last part of this paper the modelling of acoustic forces and their subsequent impact on the deposition profile through convection is examined.

Arrears end

Considers the proposed pre-action protocol for mortgage arrears aimed at residential lenders and intended to restrict their ability to seek possession. Includes responses to the Civil Justice Council's consultation, which ended in May 2008, with particular emphasis on the objections of the Council of Mortgage Lenders. [From Legal Journals Index]

South East London Palliative and End of Life Care Education and Training Strategy: Meeting the Education and Training Needs of the Health & Social Care Workforce Involved in the Care of Patients and Carers at the End of Life.

EXECUTIVE SUMMARY Aims 1. The aims of this strategy are • to ensure that a full range of education and training related to the adult end of life care pathway is available across South East London to meet the needs of our health and social care workforce • to enable those responsible for end of life care education and training commissioning to procure comprehensively from a full range of education providers in a systematic and strategic manner. Background 2. The work that underpins this strategy was begun by the South East London Cancer Network via its Palliative and End of Life Care Coordinating Group and then developed by way of the Marie Curie Delivering Choice Programme’s Education and Training work stream.