Degree of conversion of nanofilled and microhybrid composite resins photo-activated by different generations of LEDs

Objective: This study aimed at evaluating the degree of conversion (DC) of four composite resins, being one nanofilled and 3 microhybrid resins, photo-activated with second- and third-generation light-emitting diodes (LEDs). Material and methods: Filtek (TM) Z350 nanofilled composite resins and Amelogen (R) Plus, Vit-l-escence (TM) and Opallis microhybrid resins were photo-activated with two second-generation LEDs (Radii-cal and Elipar Free Light (TM) 2) and one third-generation LED (Ultra-Lume LED 5) by continuous light mode, and a quartz halogen-tungsten bulb (QHT, control). After 24 h of storage, the samples were pulverized into fine powder and 5 mg of each material were mixed with 100 mg of potassium bromide (KBr). After homogenization, they were pressed, which resulted in a pellet that was evaluated using an infrared spectromer (Nexus 470, Thermo Nicolet) equipped with TGS detector using diffuse reflectance (32 scans, resolution of 4 cm(-1)) coupled to a computer. The percentage of unreacted carbon-carbon double bonds (% C=C) was determined from the ratio of absorbance intensities of aliphatic C=C (peak at 1637 cm-1) against internal standard before and after curing of the specimen: aromatic C-C (peak at 1610 cm-1). Results: The ANOVA showed a significant effect on the interaction between the light-curing units (LCUs) and the composite resins (p<0.001). The Tukey's test showed that the nanofilled resin (Filtek (TM) Z350) and Opallis when photo-activated by the halogen lamp (QTH) had the lowest DC compared with the other microhybrid composite resins. The DC of the nanofilled resin (Filtek (TM) Z350) was also lower using LEDs. The highest degrees of conversion were obtained using the third-generation LED and one of second-generation LEDs (Elipar Free Light (TM) 2). Conclusions: The nanofilled resin showed the lowest DC, and the Vit-l-escence (TM) microhybrid composite resin showed the highest DC. Among the LCUs, it was not possible to establish an order, even though the second-generation LED Radii-cal provided the lowest DC.

An integrated approach of software development and test processes to distributed teams

The Distributed Software Development (DSD) is a development strategy that meets the globalization needs concerned with the increase productivity and cost reduction. However, the temporal distance, geographical dispersion and the socio-cultural differences, increased some challenges and, especially, added new requirements related with the communication, coordination and control of projects. Among these new demands there is the necessity of a software process that provides adequate support to the distributed software development. This paper presents an integrated approach of software development and test that considers distributed teams peculiarities. The approach purpose is to offer support to DSD, providing a better project visibility, improving the communication between the development and test teams, minimizing the ambiguity and difficulty to understand the artifacts and activities. This integrated approach was conceived based on four pillars: (i) to identify the DSD peculiarities concerned with development and test processes, (ii) to define the necessary elements to compose the integrated approach of development and test to support the distributed teams, (iii) to describe and specify the workflows, artifacts, and roles of the approach, and (iv) to represent appropriately the approach to enable the effective communication and understanding of it.

CYP2C9 and VKORC1 Polymorphisms Are Differently Distributed in the Brazilian Population According to Self-Declared Ethnicity or Genetic Ancestry

Background: Warfarin-dosing pharmacogenetic algorithms have presented different performances across ethnicities, and the impact in admixed populations is not fully known. Aims: To evaluate the CYP2C9 and VKORC1 polymorphisms and warfarin-predicted metabolic phenotypes according to both self-declared ethnicity and genetic ancestry in a Brazilian general population plus Amerindian groups. Methods: Two hundred twenty-two Amerindians (Tupinikin and Guarani) were enrolled and 1038 individuals from the Brazilian general population who were self-declared as White, Intermediate (Brown, Pardo in Portuguese), or Black. Samples of 274 Brazilian subjects from Sao Paulo were analyzed for genetic ancestry using an Affymetrix 6.0 (R) genotyping platform. The CYP2C9*2 (rs1799853), CYP2C9*3 (rs1057910), and VKORC1 g.-1639G>A (rs9923231) polymorphisms were genotyped in all studied individuals. Results: The allelic frequency for the VKORC1 polymorphism was differently distributed according to self-declared ethnicity: White (50.5%), Intermediate (46.0%), Black (39.3%), Tupinikin (40.1%), and Guarani (37.3%) (p < 0.001), respectively. The frequency of intermediate plus poor metabolizers (IM + PM) was higher in White (28.3%) than in Intermediate (22.7%), Black (20.5%), Tupinikin (12.9%), and Guarani (5.3%), (p < 0.001). For the samples with determined ancestry, subjects carrying the GG genotype for the VKORC1 had higher African ancestry and lower European ancestry (0.14 +/- 0.02 and 0.62 +/- 0.02) than in subjects carrying AA (0.05 +/- 0.01 and 0.73 +/- 0.03) (p = 0.009 and 0.03, respectively). Subjects classified as IM + PM had lower African ancestry (0.08 +/- 0.01) than extensive metabolizers (0.12 +/- 0.01) (p = 0.02). Conclusions: The CYP2C9 and VKORC1 polymorphisms are differently distributed according to self-declared ethnicity or genetic ancestry in the Brazilian general population plus Amerindians. This information is an initial step toward clinical pharmacogenetic implementation, and it could be very useful in strategic planning aiming at an individual therapeutic approach and an adverse drug effect profile prediction in an admixed population.

Analytical tools to assess the voltage stability of induction-based distributed generators

The installation of induction distributed generators should be preceded by a careful study in order to determine if the point of common coupling is suitable for transmission of the generated power, keeping acceptable power quality and system stability. In this sense, this paper presents a simple analytical formulation that allows a fast and comprehensive evaluation of the maximum power delivered by the induction generator, without losing voltage stability. Moreover, this formulation can be used to identify voltage stability issues that limit the generator output power. All the formulation is developed by using the equivalent circuit of squirrel-cage induction machine. Simulation results are used to validate the method, which enables the approach to be used as a guide to reduce the simulation efforts necessary to assess the maximum output power and voltage stability of induction generators. (C) 2011 Elsevier Ltd. All rights reserved.

Improving the Robustness of Distributed Failure Detectors in Adverse Conditions

Failure detection is at the core of most fault tolerance strategies, but it often depends on reliable communication. We present new algorithms for failure detectors which are appropriate as components of a fault tolerance system that can be deployed in situations of adverse network conditions (such as loosely connected and administered computing grids). It packs redundancy into heartbeat messages, thereby improving on the robustness of the traditional protocols. Results from experimental tests conducted in a simulated environment with adverse network conditions show significant improvement over existing solutions.

An online data access prediction and optimization approach for distributed systems

Current scientific applications have been producing large amounts of data. The processing, handling and analysis of such data require large-scale computing infrastructures such as clusters and grids. In this area, studies aim at improving the performance of data-intensive applications by optimizing data accesses. In order to achieve this goal, distributed storage systems have been considering techniques of data replication, migration, distribution, and access parallelism. However, the main drawback of those studies is that they do not take into account application behavior to perform data access optimization. This limitation motivated this paper which applies strategies to support the online prediction of application behavior in order to optimize data access operations on distributed systems, without requiring any information on past executions. In order to accomplish such a goal, this approach organizes application behaviors as time series and, then, analyzes and classifies those series according to their properties. By knowing properties, the approach selects modeling techniques to represent series and perform predictions, which are, later on, used to optimize data access operations. This new approach was implemented and evaluated using the OptorSim simulator, sponsored by the LHC-CERN project and widely employed by the scientific community. Experiments confirm this new approach reduces application execution time in about 50 percent, specially when handling large amounts of data.

Optical parametric oscillation with distributed feedback in cold atoms

There is currently a strong interest in mirrorless lasing systems(1), in which the electromagnetic feedback is provided either by disorder (multiple scattering in the gain medium) or by order (multiple Bragg reflection). These mechanisms correspond, respectively, to random lasers(2) and photonic crystal lasers(3). The crossover regime between order and disorder, or correlated disorder, has also been investigated with some success(4-6). Here, we report one-dimensional photonic-crystal lasing (that is, distributed feedback lasing(7,8)) with a cold atom cloud that simultaneously provides both gain and feedback. The atoms are trapped in a one-dimensional lattice, producing a density modulation that creates a strong Bragg reflection with a small angle of incidence. Pumping the atoms with auxiliary beams induces four-wave mixing, which provides parametric gain. The combination of both ingredients generates a mirrorless parametric oscillation with a conical output emission, the apex angle of which is tunable with the lattice periodicity.

Nondetection Index of Anti-Islanding Passive Protection of Synchronous Distributed Generators

Synchronous distributed generators are prone to operate islanded after contingencies, which is usually not allowed due to safety and power-quality issues. Thus, there are several anti-islanding techniques; however, most of them present technical limitations so that they are likely to fail in certain situations. Therefore, it is important to quantify and determine whether the scheme under study is adequate or not. In this context, this paper proposes an index to evaluate the effectiveness of anti-islanding frequency-based relays commonly used to protect synchronous distributed generators. The method is based on the calculation of a numerical index that indicates the time period that the system is unprotected against islanding considering the global period of analysis. Although this index can precisely be calculated based on several electromagnetic transient simulations, a practical method is also proposed to calculate it directly from simple analytical formulas or lookup tables. The results have shown that the proposed approach can assist distribution engineers to assess and set anti-islanding protection schemes.

Childbearing in adolescence: intergenerational dejà-vu? Evidence from a Brazilian birth cohort

Abstract Background Pregnancy in adolescence tends to repeat over generations. This event has been little studied in middle and low-income societies undergoing a rapid epidemiological transition. To assess this association it is important to adjust for socioeconomic conditions at different points in lifetime. Therefore, the aim of this study is to analyze the independent effect of adolescent childbearing in a generation on its recurrence in the subsequent generation, after adjusting for socioeconomic status at different points in life. Methods The study was conducted on a prospective cohort of singleton liveborn females from the city of Ribeirão Preto, Brazil, evaluated in 1978/79, and their daughters assessed in 2002/04. A total of 1059 mother-daughter pairs were evaluated. The women who had their first childbirth before 20 years of age were considered to be adolescent mothers. The risk of childbearing in adolescence for the daughter was modeled as a function of the occurrence of teenage childbearing in her mother, after adjustment for socio-demographic variables in a Poisson regression model. Results The rate of childbearing during adolescence was 31.4% in 1978/79 and 17.1% in 2002/04. Among the daughters of the 1st generation adolescent mothers, this rate was 26.7%, as opposed to 12.7% among the daughters of non adolescent mothers. After adjustments the risk of adolescent childbearing for the 2nd generation was 35% higher for women whose mothers had been pregnant during adolescence – RR = 1.35 (95% CI 1.04-1.74). Conclusion Adolescent childbearing in the 1st generation was a predictor of adolescent childbearing in the 2nd, regardless of socioeconomic factors determined at different points in lifetime.

Genetic aspects of adolescent idiopathic scoliosis in a family with multiple affected members: a research article

Abstract Background The etiology of idiopathic scoliosis remains unknown and different factors have been suggested as causal. Hereditary factors can also determine the etiology of the disease; however, the pattern of inheritance remains unknown. Autosomal dominant, X-linked and multifactorial patterns of inheritances have been reported. Other studies have suggested possible chromosome regions related to the etiology of idiopathic scoliosis. We report the genetic aspects of and investigate chromosome regions for adolescent idiopathic scoliosis in a Brazilian family. Methods Evaluation of 57 family members, distributed over 4 generations of a Brazilian family, with 9 carriers of adolescent idiopathic scoliosis. The proband presented a scoliotic curve of 75 degrees, as determined by the Cobb method. Genomic DNA from family members was genotyped. Results Locating a chromosome region linked to adolescent idiopathic scoliosis was not possible in the family studied. Conclusion While it was not possible to determine a chromosome region responsible for adolescent idiopathic scoliosis by investigation of genetic linkage using microsatellites markers during analysis of four generations of a Brazilian family with multiple affected members, analysis including other types of genomic variations, like single nucleotide polymorphisms (SNPs) could contribute to the continuity of this study.

SLCO1B1 rs4149056 polymorphism associated with statin-induced myopathy is differently distributed according to ethnicity in the Brazilian general population: Amerindians as a high risk ethnic group

Background Recent studies reported the association between SLCO1B1 polymorphisms and the development of statin-induced myopathy. In the scenario of the Brazilian population, being one of the most heterogeneous in the world, the main aim here was to evaluate SLCO1B1 polymorphisms according to ethnic groups as an initial step for future pharmacogenetic studies. Methods One hundred and eighty-two Amerindians plus 1,032 subjects from the general urban population were included. Genotypes for the SLCO1B1 rs4149056 (c.T521C, p.V174A, exon 5) and SLCO1B1 rs4363657 (g.T89595C, intron 11) polymorphisms were detected by polymerase chain reaction followed by high resolution melting analysis with the Rotor Gene 6000® instrument. Results The frequencies of the SLCO1B1 rs4149056 and rs4363657 C variant allele were higher in Amerindians (28.3% and 26.1%) and were lower in African descent subjects (5.7% and 10.8%) compared with Mulatto (14.9% and 18.2%) and Caucasian descent (14.8% and 15.4%) ethnic groups (p < 0.001 and p < 0.001, respectively). Linkage disequilibrium analysis show that these variant alleles are in different linkage disequilibrium patterns depending on the ethnic origin. Conclusion Our findings indicate interethnic differences for the SLCO1B1 rs4149056 C risk allele frequency among Brazilians. These data will be useful in the development of effective programs for stratifying individuals regarding adherence, efficacy and choice of statin-type.

Denominal Verbs in Brazilian Portuguese: distinguishing between diachronic and synchronic structures within Distributed Morphology approach

Recent work on argument structure has shown that there must be a synchronic relation between nouns and derived verbs that can be treated in structural terms. However, a simple phonological/morphological identity or diachronic derivation between a verb and a noun cannot guarantee that there is a denominal structure in a synchronic approach. In this paper we observe the phenomenon of Denominal Verbs in Brazilian Portuguese and argue for a distinction between etymological and synchronic morphological derivation. The objectives of this paper are 1) to identify synchronic and formal criteria to define which diachronic Denominal Verbs can also be considered denominal under a synchronic analysis; and 2) to detect in which cases the label "denominal" can be justifiably abandoned. Based on results of argument structure tests submitted to the judgments of native speakers, it was possible to classify the supposed homogenous Denominal Verbs class into three major groups: Real Denominal Verbs, Root-derived Verbs, and Ambiguous Verbs. In a Distributed Morphology approach, it was possible to explain the distinction between these groups based on the ideia of phases in words and the locality of restriction in the interpretation of roots.

Genome sequence of Xanthomonas fuscans subsp. fuscans strain 4834-R reveals that flagellar motility is not a general feature of xanthomonads

Abstract Background Xanthomonads are plant-associated bacteria responsible for diseases on economically important crops. Xanthomonas fuscans subsp. fuscans (Xff) is one of the causal agents of common bacterial blight of bean. In this study, the complete genome sequence of strain Xff 4834-R was determined and compared to other Xanthomonas genome sequences. Results Comparative genomics analyses revealed core characteristics shared between Xff 4834-R and other xanthomonads including chemotaxis elements, two-component systems, TonB-dependent transporters, secretion systems (from T1SS to T6SS) and multiple effectors. For instance a repertoire of 29 Type 3 Effectors (T3Es) with two Transcription Activator-Like Effectors was predicted. Mobile elements were associated with major modifications in the genome structure and gene content in comparison to other Xanthomonas genomes. Notably, a deletion of 33 kbp affects flagellum biosynthesis in Xff 4834-R. The presence of a complete flagellar cluster was assessed in a collection of more than 300 strains representing different species and pathovars of Xanthomonas. Five percent of the tested strains presented a deletion in the flagellar cluster and were non-motile. Moreover, half of the Xff strains isolated from the same epidemic than 4834-R was non-motile and this ratio was conserved in the strains colonizing the next bean seed generations. Conclusions This work describes the first genome of a Xanthomonas strain pathogenic on bean and reports the existence of non-motile xanthomonads belonging to different species and pathovars. Isolation of such Xff variants from a natural epidemic may suggest that flagellar motility is not a key function for in planta fitness.