Projeto, implementação e análise de um conversor CC-CC de alto ganho e alto rendimento para aplicações fotovoltaicas

In recent years the photovoltaic generation has had greater insertion in the energy mix of the most developed countries, growing at annual rates of over 30%. The pressure for the reduction of pollutant emissions, diversification of the energy mix and the drop in prices are the main factors driving this growth. Grid tied systems plays an important role in alleviating the energy crisis and diversification of energy sources. Among the grid tied systems, building integrated photovoltaic systems suffers from partial shading of the photovoltaic modules and consequently the energy yield is reduced. In such cases, classical forms of modules connection do not produce good results and new techniques have been developed to increase the amount of energy produced by a set of modules. In the parallel connection technique of photovoltaic modules, a high voltage gain DC-DC converter is required, which is relatively complex to build with high efficiency. The current-fed isolated converters explored in this work have some desirable characteristics for this type of application, such as: low input current ripple and input voltage ripple, high voltage gain, galvanic isolation, feature high power capacity and it achieve soft switching in a wide operating range. This study presents contributions to the study of a high gain and high efficiency DC-DC converter for use in a parallel system of photovoltaic generation, being possible the use in a microinverter or with central inverter. The main contributions of this work are: analysis of the active clamping circuit operation proposing that the clamp capacitor connection must be done on the negative node of the power supply to reduce the input current ripple and thus reduce the filter requirements; use of a voltage doubler in the output rectifier to reduce the number of components and to extend the gain of the converter; detailed study of the converter components in order to raise the efficiency; obtaining the AC equivalent model and control system design. As a result, a DC-DC converter with high gain, high efficiency and without electrolytic capacitors in the power stage was developed. In the final part of this work the DC-DC converter operation connected to an inverter is presented. Besides, the DC bus controller is designed and are implemented two maximum power point tracking algorithms. Experimental results of full system operation connected to an emulator and subsequently to a real photovoltaic module are also given.

Educação financeira no ensino médio: uma abordagem por meio da análise de produtos financeiros com ênfase em consórcios

This paper presents a differential approach of financial mathematics developed in high school, focusing on financial education. We seek through the insertion of texts, analysis of some financial products and by the interpretation of problems to contribute to the financial training of students. Aiming to make financial mathematics more attractive and accessible to the day-today, there are available for studies some practical tools like the citizen calculator which are available for computers and mobile phones. As well as spreadsheets and software Geogebra, that allow you to compare and analyze the financial costs of consortia, financing and financial applications,in addition to being allied in the preparation and control of personal and family budget. By applying the teaching sequence proposed in a nocturnal class of high school, we realized some difficulties that have limited the financial learning of math concepts.Yet identified progress regarding the financial education of students. These observations were made through qualitative and quantitative analysis from notes in the field diary and also answers given by students in specific form.

Análise e projeto de um conversor boost de três níveis intercalado

This paper presents the development of a boost converter with the possibility of higher gain than the conventional boost converter for applications under similar conditions and increased power. Presents the main concepts involving the boost converter and two variations: the boost converter of three levels and the boost converter interspersed with two converter cells. The breakdown mounting positions, the operating steps, the addressing and the main strengths of each converter in order to check for possible uses in the construction of a prototype joining their main advantages. In the presentation of this converter addresses the operating steps, the equation governing its design, the simulations obtained through software (PSIM), a comparison between the boost converter models studied and the experimental results.

Transformada wavelet aplicada a análise automática de oscilografias de curta duração em unidades geradoras

The focus of this work is the automatic analysis of disturbance records for electrical power generating units. The main proposition is a method based on wavelet transform applied to short-term disturbance records (waveform records). The goal of the method is to detect the time instants of recorded disturbances and extract meaningful information that characterize the faults. The result is a set of representative information of the monitored signals in power generators. This information can be further classified by an expert system (or other classification method) in order to classify the faults and other abnormal operating conditions. The large amount of data produced by digital fault recorders during faults justify the research of methods to assist the analysts in their task of analysing the disturbances. The literature review pointed out the state of the art and possible applications for oscillography records. The review of the COMTRADE standard and wavelet transform underlines the choice of the method for solving the problem. The conducted tests lead to the determination of the best mother wavelet for the segmentation process. The application of the proposed method to five case studies with real oscillographic records confirmed the accuracy and efficiency of the proposed scheme. With this research, the post-operation analysis of occurrences is improved and as a direct result is the reduction of the time that generators are offline.

Análise e proposição de estratégias de estimação e controle de velocidade para motores de indução trifásicos

This study presents a proposal of speed servomechanisms without the use of mechanical sensors (sensorless) using induction motors. A comparison is performed and propose techniques for pet rotor speed, analyzing performance in different conditions of speed and load. For the determination of control technique, initially, is performed an analysis of the technical literature of the main control and speed estimation used, with their characteristics and limitations. The proposed technique for servo sensorless speed induction motor uses indirect field-oriented control (IFOC), composed of four controllers of the proportional-integral type (PI): rotor flux controller, speed controller and current controllers in the direct and quadrature shaft. As the main focus of the work is in the speed control loop was implemented in Matlab the recursive least squares algorithm (RLS) for identification of mechanical parameters, such as moment of inertia and friction coefficient. Thus, the speed of outer loop controller gains can be self adjusted to compensate for any changes in the mechanical parameters. For speed estimation techniques are analyzed: MRAS by rotóricos fluxes MRAS by counter EMF, MRAS by instantaneous reactive power, slip, locked loop phase (PLL) and sliding mode. A proposition of estimation in sliding mode based on speed, which is performed a change in rotor flux observer structure is displayed. To evaluate the techniques are performed theoretical analyzes in Matlab simulation environment and experimental platform in electrical machinery drives. The DSP TMS320F28069 was used for experimental implementation of speed estimation techniques and check the performance of the same in a wide speed range, including load insertion. From this analysis is carried out to implement closed-loop control of sensorless speed IFOC structure. The results demonstrated the real possibility of replacing mechanical sensors for estimation techniques proposed and analyzed. Among these, the estimator based on PLL demonstrated the best performance in various conditions, while the technique based on sliding mode has good capacity estimation in steady state and robustness to parametric variations.

Caracterização química, atividade antioxidante e antimicrobiana do óleo essencial de Baccharis oreophila Malme

The Baccharis oreophila Malme belongs to the Asteraceae family. In Brazil are reported 120 species of Baccharis, most located in the South and Southeast regions, the latter presents the highest prevalence, especially in the state of São Paulo. Asteraceae is well known for the production of essential oils, which are liquid, volatile and aromatic substances produced by plants specialized for metabolism possess antibacterial, antifungal, and antioxidant properties. Thus, this study aimed, perform chemical and evaluate the antimicrobial and antioxidant activity of essential oil from dried leaves of B. oreophila collected in winter in Piraquara, Paraná. Obtaining essential oil was given by hydrodistillation in Clevenger apparatus, in triplicate, and the analysis was done using a gas chromatograph coupled to mass spectrometry GC / MS. The identification of the components was made based on retention indices calculated from the co-injection of a series of n-alkanes, followed by comparison of their mass spectra with literature. The antimicrobial activity was assessed by disk diffusion method and microdilution. The antioxidant activity was evaluated by the methods DPPH equivalent Trolox, ABTS and FRAP equivalent Trolox equivalent ferrous sulfate. The essential oil showed 0.47% yield. They identified 57 components (89.38%), 1.51% were classified as hydrogenated monoterpenes, oxygenated monoterpenes 15.14%, 34.84% and 37.87% hydrogenated sesquiterpenes sesquiterpenes oxygenates. As the major components were detected kusimono (16.37%), spathulenol (16.12%), the δ-cadinene (5.68%) and bicyclogermacrene (4.09%). The antimicrobial activity of essential oil was performed for the microorganisms Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 25923, Candida albicans ATCC 18804 and Candida tropicalis ATCC 13803, the results showed that the essential oil showed activity against S. aureus Inhibitory Concentration minimum (CIM) 1250 g/mL. In the evaluation of antioxidant activity essential oil showed antioxidant potential for the three methods evaluated, with values of 1,468 m.mol.L-1, 7.126 m.mol.L-1 and 45.515 m.mol.L-1 for ABTS, DPPH and FRAP, respectively. These results demonstrate that the essential oil of B. oreophila showed antimicrobial potential against S. aureus and interesting antioxidant activity, especially for the reducing power of iron ion, demonstrating their potential for future industrial applications. It is important to emphasize that were not observed in the literature reports highlighting such biological properties of B. oreophila oil.

Características químicas do solo e desempenho de culturas após quatro anos de aplicações de cama de aviário em diferentes épocas e níveis

Due to the high supply and its attractive cost, the poultry litter has been used in the southwestern region of Parana to the improvement of soil fertility seeking greater production of grains and pastures. However, the use without technical knowledge can minimize the benefits of poultry litter or even cause undesirable effects on soil, environmental pollution and also productivity losses in the used crops. The objective of this study was to evaluate the influence of different times of poultry litter application, predating the winter crop, associated with increasing levels, about soil chemical properties, release of nutrients and crop performances in four consecutive years (2011-2014). In the first three years the experimental design was randomized blocks with a split plot system and four replications. In the main plots were tested four poultry litter application times preceding the wheat production: 0, 15, 30 and 45 days before sowing (DAS); in the subplots were applied four poultry litter levels (wet basis): 0, 4, 8 and 12 Mg ha-1. Last year one more subdivision of plots was done, evaluating the use or not of nitrogen in coverage in wheat, at a dose of 100 kg N ha-1. The wheat cultivar used in the four years was the BRS 220. In three years it was evaluated the residual effect on soybean production (cultivar - BMX Turbo RR) and in one year on the beans. The chemical soil attributes were evaluated at four depths 0-2,5cm, 2,5-5cm, 5-10cm and 10-20cm, and also the rate of decomposition and nutrient release of poultry litter and the crop productivity. The different times of application concerning the poultry litter had little influence on the studied variables, demonstrating that the producer does not need to have a specific date (before planting) to the application of poultry litter. Potassium was fully released 60 days after the allocation of litter bags into the field; for nitrogen and phosphorus the release was slower. The use of increasing levels of poultry litter increased the levels of various soil elements, highlighting the potassium which reached 20 cm deep in the second year of evaluation. The increase in pH and in the base saturation occurred only in the upper layers, while the phosphorus reached 10 cm deep in the third year of the study. It was observed increased pH and base saturation. The use of increasing doses of poultry litter contributed to the wheat plant nutrition, significantly increasing the weight of a thousand grains, and the grain yield of wheat in all the evaluated years; the nitrogen fertilization in coverage also had significant effect for the fourth evaluated year. Also there was a significant response from the residual effect of poultry litter for crops planted in summer for both soybeans and beans.

Estatística das aplicações de métodos multicritério nas áreas da engenharia de produção

Currently, the decision analysis in production processes involves a level of detail, in which the problem is subdivided to analyze it in terms of different and conflicting points of view. The multi-criteria analysis has been an important tool that helps assertive decisions related to the production process. This process of analysis has been incorporated into various areas of production engineering, by applying multi-criteria methods in solving the problems of the productive sector. This research presents a statistical study on the use of multi-criteria methods in the areas of Production Engineering, where 935 papers were filtered from 20.663 publications in scientific journals, considering a level of the publication quality based on the impact factor published by the JCR between 2010 and 2015. In this work, the descriptive statistics is used to represent some information and statistical analysis on the volume of applications methods. Relevant results were found with respect to the "amount of advanced methods that are being applied and in which areas related to Production Engineering." This information may provide support to researchers when preparing a multi-criteria application, whereupon it will be possible to check in which issues and how often the other authors have used multi-criteria methods.