Flight guardian: a common avionics architecture for collision avoidance and safe emergency landing for unmanned aerial systems

This paper presents an approach to derive requirements for an avionics architecture that provides onboard sense-and-avoid and autonomous emergency forced landing capabilities to a UAS. The approach is based on two design paradigms that (1) derive requirements analyzing the common functionality between these two functions to then derive requirements for sensors, computing capability, interfaces, etc. (2) consider the risk and safety mitigation associated with these functions to derive certification requirements for the system design. We propose to use the Aircraft Certification Matrix (ACM) approach to tailor the system Development Assurance Levels (DAL) and architecture requirements in accordance with acceptable risk criteria. This architecture is developed under the name “Flight Guardian”. Flight Guardian is an avionics architecture that integrates common sensory elements that are essential components of any UAS that is required to be dependable. The Flight Guardian concept is also applicable to conventionally piloted aircraft, where it will serve to reduce cockpit workload.

Communication Architecture Design for Real-Time Networked Control Systems

Networked control over data networks has received increasing attention in recent years. Among many problems in networked control systems (NCSs) is the need to reduce control latency and jitter and to deal with packet dropouts. This paper introduces our recent progress on a queuing communication architecture for real-time NCS applications, and simple strategies for dealing with packet dropouts. Case studies for a middle-scale process or multiple small-scale processes are presented for TCP/IP based real-time NCSs. Variations of network architecture design are modelled, simulated, and analysed for evaluation of control latency and jitter performance. It is shown that a simple bandwidth upgrade or adding hierarchy does not necessarily bring benefits for performance improvement of control latency and jitter. A co-design of network and control is necessary to maximise the real-time control performance of NCSs

Adaptive modelling of sustainable architecture design in entropy evolutionary

This paper argues a model of adaptive design for sustainable architecture within a framework of entropy evolution. The spectrum of sustainable architecture consists of efficient use of energy and material resource in the life-cycle of buildings, active involvement of the occupants into micro-climate control within the building, and the natural environment as the physical context. The interactions amongst all the parameters compose a complex system of sustainable architecture design, of which the conventional linear and fragmented design technologies are insufficient to indicate holistic and ongoing environmental performance. The latest interpretation of the Second Law of Thermodynamics states a microscopic formulation of an entropy evolution of complex open systems. It provides a design framework for an adaptive system evolves for the optimization in open systems, this adaptive system evolves for the optimization of building environmental performance. The paper concludes that adaptive modelling in entropy evolution is a design alternative for sustainable architecture.

A hybrid agent architecture for modeling autonomous agents in SAGE

This paper highlights the Hybrid agent construction model being developed that allows the description and development of autonomous agents in SAGE (Scalable, fault Tolerant Agent Grooming Environment) - a second generation FIPA-Compliant Multi-Agent system. We aim to provide the programmer with a generic and well defined agent architecture enabling the development of sophisticated agents on SAGE, possessing the desired properties of autonomous agents - reactivity, pro-activity, social ability and knowledge based reasoning. © Springer-Verlag Berlin Heidelberg 2005.

The InstaBooth: Making common ground for media architectural design

Media architecture has emerged from and relies upon a range of different disciplinary traditions and areas of expertise. As this field develops, it is timely to reflect upon the ways in which designers of different disciplinary stripes can be brought together to collaborate in a design process. What are the means by which design teams can establish a ‘common ground’ where design work can take place while recognizing the diversity of ways of working those different disciplines bring to the process? A co-design approach has been the fundamental backbone of the InstaBooth project, which has brought together a multidisciplinary design team of academics and practitioners. The intention of this project has been to explore the combination of digital and physical interactions within a small media architecture installation to intervene with urban environments and public places for the purposes of community engagement. It is by exploring the design process of the InstaBooth project that we highlight the value of multi-disciplinary collaborations, the lessons that can be learned, and the struggles and hurdles along the way. This paper highlights the iterative process of design, the materials and physical prototypes that were employed to ultimately create a working version of the InstaBooth, a media architecture that evolves as users push its boundaries and take ownership of the installation. The concept of the InstaBooth continues to develop not only as more data are collected on its mechanics and potentials through observations, interviews and workshops, but also as more and more users engage with the installation in their individual ways.

First year design "Visualisation II": The hybridisation of analogue and digital tools

This paper discusses first year students’ responses and outcomes to the integration of digital technologies in their second semester foundational visualisation class; ‘Visualisation II’. As the second class in the Visualisation series, previous analogue knowledge taught in ‘Visualisation I’ is compounded with new digital technologies establishing the introduction to a myriad of hybrid visualisation tools and techniques for design exploration and design artefact. This research examines the differentiation between analogue and digital design, common precedents of the two, and reflects upon the environment and class structure with the learning experiences and confidence of surveyed participants.

The shifting value of design in the Australian Architecture Industry

Architects regularly employ design as a problem-solving tool in the built environment. Within the design process, architects apply design thinking to reframe problems as opportunities, take advantage of contradictory information to develop new solutions, and differentiate outcomes based on context. This research aims to investigate how design can be better positioned to develop greater differentiated value to an architect’s current service offering, and how design as a strategy could be applied as a driver of business innovation within the Australian architecture industry. The research will explore literature relating to the future of architecture, the application of design thinking, and the benefits of strategic design. The future intent of the research is to develop strategies that improve the value offering of architects, and develop design led solutions that could be applied successfully to the business of architecture.

Value-oriented process modeling : integrating financial perspectives into business process re-design

Purpose – Financial information about costs and return on investments are of key importance to strategic decision-making but also in the context of process improvement or business engineering. In this paper we propose a value-oriented approach to business process modeling based on key concepts and metrics from operations and financial management, to aid decision making in process re-design projects on the basis of process models. Design/methodology/approach – We suggest a theoretically founded extension to current process modeling approaches, and delineate a framework as well as methodical support to incorporate financial information into process re-design. We use two case studies to evaluate the suggested approach. Findings – Based on two case studies, we show that the value-oriented process modeling approach facilitates and improves managerial decision-making in the context of process re-design. Research limitations / implications – We present design work and two case studies. More research is needed to more thoroughly evaluate the presented approach in a variety of real-life process modeling settings. Practical implications – We show how our approach enables decision makers to make investment decisions in process re-design projects, and also how other decisions, for instance in the context of enterprise architecture design, can be facilitated. Originality/value – This study reports on an attempt to integrate financial considerations into the act of process modeling, in order to provide more comprehensive decision making support in process re-design projects.

Remediation strategies of shaft and common mode voltages in adjustable speed drive systems

AC motors are largely used in a wide range of modern systems, from household appliances to automated industry applications such as: ventilations systems, fans, pumps, conveyors and machine tool drives. Inverters are widely used in industrial and commercial applications due to the growing need for speed control in ASD systems. Fast switching transients and the common mode voltage, in interaction with parasitic capacitive couplings, may cause many unwanted problems in the ASD applications. These include shaft voltage and leakage currents. One of the inherent characteristics of Pulse Width Modulation (PWM) techniques is the generation of the common mode voltage, which is defined as the voltage between the electrical neutral of the inverter output and the ground. Shaft voltage can cause bearing currents when it exceeds the amount of breakdown voltage level of the thin lubricant film between the inner and outer rings of the bearing. This phenomenon is the main reason for early bearing failures. A rapid development in power switches technology has lead to a drastic decrement of switching rise and fall times. Because there is considerable capacitance between the stator windings and the frame, there can be a significant capacitive current (ground current escaping to earth through stray capacitors inside a motor) if the common mode voltage has high frequency components. This current leads to noises and Electromagnetic Interferences (EMI) issues in motor drive systems. These problems have been dealt with using a variety of methods which have been reported in the literature. However, cost and maintenance issues have prevented these methods from being widely accepted. Extra cost or rating of the inverter switches is usually the price to pay for such approaches. Thus, the determination of cost-effective techniques for shaft and common mode voltage reduction in ASD systems, with the focus on the first step of the design process, is the targeted scope of this thesis. An introduction to this research – including a description of the research problem, the literature review and an account of the research progress linking the research papers – is presented in Chapter 1. Electrical power generation from renewable energy sources, such as wind energy systems, has become a crucial issue because of environmental problems and a predicted future shortage of traditional energy sources. Thus, Chapter 2 focuses on the shaft voltage analysis of stator-fed induction generators (IG) and Doubly Fed Induction Generators DFIGs in wind turbine applications. This shaft voltage analysis includes: topologies, high frequency modelling, calculation and mitigation techniques. A back-to-back AC-DC-AC converter is investigated in terms of shaft voltage generation in a DFIG. Different topologies of LC filter placement are analysed in an effort to eliminate the shaft voltage. Different capacitive couplings exist in the motor/generator structure and any change in design parameters affects the capacitive couplings. Thus, an appropriate design for AC motors should lead to the smallest possible shaft voltage. Calculation of the shaft voltage based on different capacitive couplings, and an investigation of the effects of different design parameters are discussed in Chapter 3. This is achieved through 2-D and 3-D finite element simulation and experimental analysis. End-winding parameters of the motor are also effective factors in the calculation of the shaft voltage and have not been taken into account in previous reported studies. Calculation of the end-winding capacitances is rather complex because of the diversity of end winding shapes and the complexity of their geometry. A comprehensive analysis of these capacitances has been carried out with 3-D finite element simulations and experimental studies to determine their effective design parameters. These are documented in Chapter 4. Results of this analysis show that, by choosing appropriate design parameters, it is possible to decrease the shaft voltage and resultant bearing current in the primary stage of generator/motor design without using any additional active and passive filter-based techniques. The common mode voltage is defined by a switching pattern and, by using the appropriate pattern; the common mode voltage level can be controlled. Therefore, any PWM pattern which eliminates or minimizes the common mode voltage will be an effective shaft voltage reduction technique. Thus, common mode voltage reduction of a three-phase AC motor supplied with a single-phase diode rectifier is the focus of Chapter 5. The proposed strategy is mainly based on proper utilization of the zero vectors. Multilevel inverters are also used in ASD systems which have more voltage levels and switching states, and can provide more possibilities to reduce common mode voltage. A description of common mode voltage of multilevel inverters is investigated in Chapter 6. Chapter 7 investigates the elimination techniques of the shaft voltage in a DFIG based on the methods presented in the literature by the use of simulation results. However, it could be shown that every solution to reduce the shaft voltage in DFIG systems has its own characteristics, and these have to be taken into account in determining the most effective strategy. Calculation of the capacitive coupling and electric fields between the outer and inner races and the balls at different motor speeds in symmetrical and asymmetrical shaft and balls positions is discussed in Chapter 8. The analysis is carried out using finite element simulations to determine the conditions which will increase the probability of high rates of bearing failure due to current discharges through the balls and races.

Spatial stimulus : Model making in the architectural design studio

This action research examines the enhancement of visual communication within the architectural design studio through physical model making. „It is through physical model making that designers explore their conceptual ideas and develop the creation and understanding of space,‟ (Salama & Wilkinson 2007:126). This research supplements Crowther‟s findings extending the understanding of visual dialogue to include physical models. „Architecture Design 8‟ is the final core design unit at QUT in the fourth year of the Bachelor of Design Architecture. At this stage it is essential that students have the ability to communicate their ideas in a comprehensive manner, relying on a combination of skill sets including drawing, physical model making, and computer modeling. Observations within this research indicates that students did not integrate the combination of the skill sets in the design process through the first half of the semester by focusing primarily on drawing and computer modeling. The challenge was to promote deeper learning through physical model making. This research addresses one of the primary reasons for the lack of physical model making, which was the limited assessment emphasis on the physical models. The unit was modified midway through the semester to better correlate the lecture theory with studio activities by incorporating a series of model making exercises conducted during the studio time. The outcome of each exercise was assessed. Tutors were surveyed regarding the model making activities and a focus group was conducted to obtain formal feedback from students. Students and tutors recognised the added value in communicating design ideas through physical forms and model making. The studio environment was invigorated by the enhanced learning outcomes of the students who participated in the model making exercises. The conclusions of this research will guide the structure of the upcoming iteration of the fourth year design unit.

Design from the everyday: continuously evolving, embedded exploratory prototypes

One of the major challenges in the design of social technologies is the evaluation of their qualities of use and how they are appropriated over time. While the field of HCI abounds in short-term exploratory design and studies of use, relatively little attention has focused on the continuous development of prototypes longitudinally and studies of their emergent use. We ground the exploration and analysis of use in the everyday world, embracing contingency and open-ended use, through the use of a continuously-available exploratory prototype. Through examining use longitudinally, clearer insight can be gained of realistic, non-novelty usage and appropriation into everyday use. This paper sketches out a framework for design that puts a premium on immediate use and evolving the design in response to use and user feedback. While such design practices with continuously developing systems are common in the design of social technologies, they are little documented. We describe our approach and reflect upon its key characteristics, based on our experiences from two case studies. We also present five major patterns of long-term usage which we found useful for design.

Design for disassembly : an architectural strategy

A study of historic examples of buildings that were designed for disassembly reveals a number of important lessons in the technology employed. These lessons can inform designers such that they may better design for disassembly to attempt to increase the rates of reuse and recycling in the building industry.

Learning landscapes 2.0 : warning - assembly required

Twenty first century learners operate in organic, immersive environments. A pedagogy of student-centred learning is not a recipe for rooms. A contemporary learning environment is like a landscape that grows, morphs, and responds to the pressures of the context and micro-culture. There is no single adaptable solution, nor a suite of off-the-shelf answers; propositions must be customisable and infinitely variable. They must be indeterminate and changeable; based on the creation of learning places, not restrictive or constraining spaces. A sustainable solution will be un-fixed, responsive to the life cycle of the components and materials, able to be manipulated by the users; it will create and construct its own history. Learning occurs as formal education with situational knowledge structures, but also as informal learning, active learning, blended learning social learning, incidental learning, and unintended learning. These are not spatial concepts but socio-cultural patterns of discovery. Individual learning requirements must run free and need to be accommodated as the learner sees fit. The spatial solution must accommodate and enable a full array of learning situations. It is a system not an object. Three major components: 1. The determinate landscape: in-situ concrete 'plate' that is permanent. It predates the other components of the system and remains as a remnant/imprint/fossil after the other components of the system have been relocated. It is a functional learning landscape in its own right; enabling a variety of experiences and activities. 2. The indeterminate landscape: a kit of pre-fabricated 2-D panels assembled in a unique manner at each site to suit the client and context. Manufactured to the principles of design-for-disassembly. A symbiotic barnacle like system that attaches itself to the existing infrastructure through the determinate landscape which acts as a fast growth rhizome. A carapace of protective panels, infinitely variable to create enclosed, semi-enclosed, and open learning places. 3. The stations: pre-fabricated packages of highly-serviced space connected through the determinate landscape. Four main types of stations; wet-room learning centres, dry-room learning centres, ablutions, and low-impact building services. Entirely customised at the factory and delivered to site. The stations can be retro-fitted to suit a new context during relocation. Principles of design for disassembly: material principles • use recycled and recyclable materials • minimise the number of types of materials • no toxic materials • use lightweight materials • avoid secondary finishes • provide identification of material types component principles • minimise/standardise the number of types of components • use mechanical not chemical connections • design for use of common tools and equipment • provide easy access to all components • make component size to suite means of handling • provide built in means of handling • design to realistic tolerances • use a minimum number of connectors and a minimum number of types system principles • design for durability and repeated use • use prefabrication and mass production • provide spare components on site • sustain all assembly and material information

Basic graphics : an introduction to rudimentary graphic design

These notes were compiled from several authorities to be used for teaching and learning purposes here at QUT, with the focus on first and second year landscape architecture design studio units.

Design basics : an introduction to rudimentary design ideas and sources

These notes were compiled from several authorities to be used for teaching and learning purposes here at QUT, with the focus on first and second year landscape architecture design studio units.