Peak-to-average power ratio of IEEE 802.11a PHY layer signals

In this chapter we propose clipping with amplitude and phase corrections to reduce the peak-to-average power ratio (PAR) of orthogonal frequency division multiplexed (OFDM) signals in high-speed wireless local area networks defined in IEEE 802.11a physical layer. The proposed techniques can be implemented with a small modification at the transmitter and the receiver remains standard compliant. PAR reduction as much as 4dB can be achieved by selecting a suitable clipping ratio and a correction factor depending on the constellation used. Out of band noise (OBN) is also reduced.

Interleaved PC-OFDM to reduce peak-to-average power ratio

Parallel combinatory orthogonal frequency division multiplexing (PC-OFDM yields lower maximum peak-to-average power ratio (PAR), high bandwidth efficiency and lower bit error rate (BER) on Gaussian channels compared to OFDM systems. However, PC-OFDM does not improve the statistics of PAR significantly. In this chapter, the use of a set of fixed permutations to improve the statistics of the PAR of a PC-OFDM signal is presented. For this technique, interleavers are used to produce K-1 permuted sequences from the same information sequence. The sequence with the lowest PAR, among K sequences is chosen for the transmission. The PAR of a PC-OFDM signal can be further reduced by 3-4 dB by this technique. Mathematical expressions for the complementary cumulative density function (CCDF)of PAR of PC-OFDM signal and interleaved PC-OFDM signal are also presented.

Beam steering with high front-to-back ratio and high directivity on small platforms using decoupled antenna pairs

Beam steering with high front-to-back ratio and high directivity on a small platform is proposed. Two closely spaced antenna pairs with eigenmode port decoupling are used as the basic radiating elements. Two orthogonal radiation patterns are obtained for each antenna pair. High front-to-back ratio and high directivity are achieved by combining the two orthogonal radiation patterns. With an infinite groundplane, a front-to-back ratio of 21 dB with a directivity of 9.8 dB can be achieved. Beam steering, at the expense of a slight decrease in directivity, is achieved by placing the two antenna pairs 0.5λ apart. The simulated half power beamwidth is 58°. A prototype was designed and the 2-D radiation patterns were measured. The prototype supports three directions of beam steering. The half power beamwidth was measured as 46°, 48°, and 50° for the three respective beam directions. The measured front-to-back ratio in azimuth plane is 8.5 dB, 8.0 dB and 7.6 dB, respectively.

The creative sector in New Zealand : mapping and economic role : report to New Zealand Trade and Enterprise

The New Zealand creative sector was responsible for almost 121,000 jobs at the time of the 2006 Census (6.3% of total employment). These are divided between • 35,751 creative specialists – persons employed doing creative work in creative industries • 42,300 support workers - persons providing management and support services in creative industries • 42,792 embedded creative workers – persons engaged in creative work in other types of enterprise The most striking feature of this breakdown is the fact that the largest group of creative workers are employed outside the creative industries, i.e. in other types of businesses. Even within the creative industries, there are fewer people directly engaged in creative work than in providing management and support. Creative sector employees earned incomes of approximately $52,000 per annum at the time of the 2006 Census. This is relatively uniform across all three types of creative worker, and is significantly above the average for all employed persons (of approximately $40,700). Creative employment and incomes were growing strongly over both five year periods between the 1996, 2001 and 2006 Censuses. However, when we compare creative and general trends, we see two distinct phases in the development of the creative sector: • rapid structural growth over the five years to 2001 (especially led by developments in ICT), with creative employment and incomes increasing rapidly at a time when they were growing modestly across the whole economy; • subsequent consolidation, with growth driven by more by national economic expansion than structural change, and creative employment and incomes moving in parallel with strong economy-wide growth. Other important trends revealed by the data are that • the strongest growth during the decade was in embedded creative workers, especially over the first five years. The weakest growth was in creative specialists, with support workers in creative industries in the middle rank, • by far the strongest growth in creative industries’ employment was in Software & digital content, which trebled in size over the decade Comparing New Zealand with the United Kingdom and Australia, the two southern hemisphere nations have significantly lower proportions of total employment in the creative sector (both in creative industries and embedded employment). New Zealand’s and Australia’s creative shares in 2001 were similar (5.4% each), but in the following five years, our share has expanded (to 5.7%) whereas Australia’s fell slightly (to 5.2%) – in both cases, through changes in creative industries’ employment. The creative industries generated $10.5 billion in total gross output in the March 2006 year. Resulting from this was value added totalling $5.1b, representing 3.3% of New Zealand’s total GDP. Overall, value added in the creative industries represents 49% of industry gross output, which is higher than the average across the whole economy, 45%. This is a reflection of the relatively high labour intensity and high earnings of the creative industries. Industries which have an above-average ratio of value added to gross output are usually labour-intensive, especially when wages and salaries are above average. This is true for Software & Digital Content and Architecture, Design & Visual Arts, with ratios of 60.4% and 55.2% respectively. However there is significant variation in this ratio between different parts of the creative industries, with some parts (e.g. Software & Digital Content and Architecture, Design & Visual Arts) generating even higher value added relative to output, and others (e.g. TV & Radio, Publishing and Music & Performing Arts) less, because of high capital intensity and import content. When we take into account the impact of the creative industries’ demand for goods and services from its suppliers and consumption spending from incomes earned, we estimate that there is an addition to economic activity of: • $30.9 billion in gross output, $41.4b in total • $15.1b in value added, $20.3b in total • 158,100 people employed, 234,600 in total The total economic impact of the creative industries is approximately four times their direct output and value added, and three times their direct employment. Their effect on output and value added is roughly in line with the average over all industries, although the effect on employment is significantly lower. This is because of the relatively high labour intensity (and high earnings) of the creative industries, which generate below-average demand from suppliers, but normal levels of demand though expenditure from incomes. Drawing on these numbers and conclusions, we suggest some (slightly speculative) directions for future research. The goal is to better understand the contribution the creative sector makes to productivity growth; in particular, the distinctive contributions from creative firms and embedded creative workers. The ideas for future research can be organised into the several categories: • Understanding the categories of the creative sector– who is doing the business? In other words, examine via more fine grained research (at a firm level perhaps) just what is the creative contribution from the different aspects of the creative sector industries. It may be possible to categorise these in terms of more or less striking innovations. • Investigate the relationship between the characteristics and the performance of the various creative industries/ sectors; • Look more closely at innovation at an industry level e.g. using an index of relative growth of exports, and see if this can be related to intensity of use of creative inputs; • Undertake case studies of the creative sector; • Undertake case studies of the embedded contribution to growth in the firms and industries that employ them, by examining taking several high performing noncreative industries (in the same way as proposed for the creative sector). • Look at the aggregates – drawing on the broad picture of the extent of the numbers of creative workers embedded within the different industries, consider the extent to which these might explain aspects of the industries’ varied performance in terms of exports, growth and so on. • This might be able to extended to examine issues like the type of creative workers that are most effective when embedded, or test the hypothesis that each industry has its own particular requirements for embedded creative workers that overwhelms any generic contributions from say design, or IT.

A preliminary investigation of the role of the Phenylalynine: Tyrosine Ratio in children with early and continuously treated phenylketonuria : toward identification of “safe” levels

Children with early and continuously treated phenylketonuria (ECT-PKU) remain at risk of developing executive function (EF) deficits. There is some evidence that a high phenylalanine to tyrosine ratio (phe:tyr) is more strongly associated with impaired EF development than high phenylalanine alone. This study examined EF in a sample of 11 adolescents against concurrent and historical levels of phenylalanine, phe:tyr, and tyrosine. Lifetime measures of phe:tyr were more strongly associated with EF than phenylalanine-only measures. Children with a lifetime phe:tyr less than 6 demonstrated normal EF, whereas children who had a lifetime phe:tyr above 6, on average, demonstrated clinically impaired EF.

Characterizing the signal pattern of a four-cylinder diesel engine using acoustic emission and vibration analysis

Condition monitoring of diesel engines can prevent unpredicted engine failures and the associated consequence. This paper presents an experimental study of the signal characteristics of a 4-cylinder diesel engine under various loading conditions. Acoustic emission, vibration and in-cylinder pressure signals were employed to study the effectiveness of these techniques for condition monitoring and identifying symptoms of incipient failures. An event driven synchronous averaging technique was employed to average the quasi-periodic diesel engine signal in the time domain to eliminate or minimize the effect of engine speed and amplitude variations on the analysis of condition monitoring signal. It was shown that acoustic emission (AE) is a better technique than vibration method for condition monitor of diesel engines due to its ability to produce high quality signals (i.e., excellent signal to noise ratio) in a noisy diesel engine environment. It was found that the peak amplitude of AE RMS signals correlating to the impact-like combustion related events decreases in general due to a more stable mechanical process of the engine as the loading increases. A small shift in the exhaust valve closing time was observed as the engine load increases which indicates a prolong combustion process in the cylinder (to produce more power). On the contrary, peak amplitudes of the AE RMS attributing to fuel injection increase as the loading increases. This can be explained by the increase fuel friction caused by the increase volume flow rate during the injection. Multiple AE pulses during the combustion process were identified in the study, which were generated by the piston rocking motion and the interaction between the piston and the cylinder wall. The piston rocking motion is caused by the non-uniform pressure distribution acting on the piston head as a result of the non-linear combustion process of the engine. The rocking motion ceased when the pressure in the cylinder chamber stabilized.

Using low dose computerized tomography to morphometrically analyse the thoracic intervertebral foramen osseous anatomy in adolescent idiopathic scoliosis

INTRODUCTION The dimensions of the thoracic intervertebral foramen in adolescent idiopathic scoliosis (AIS) have not previously been quantified. During posterior approach scoliosis correction surgery pedicle screws may occasionally breach into the foramen. Better understanding of the dimensions of the foramen may be useful in surgical planning. This study describes a reproducible method for measurement of the thoracic foramen in AIS using computerized tomography (CT). METHODS In 23 pre-operative female patients with Lenke 1 type AIS with right side convexity major curves confined to the thoracic spine the foraminal height (FH), foraminal width (FW), pedicle to superior articular process distance (P-SAP) and cross sectional foraminal area (FA) were measured using multiplanar reconstructed CT. Measurements were made at entrance, midpoint and exit of the thoracic foramina from T1/T2 to T11/T12. Results were correlated with potential dependent variables of major curve Cobb Angle measured on X-ray and CT, Age, Weight, Lenke classification subtype, Risser Grade and number of spinal levels in the major curve. RESULTS The FH, FW, P-SAP and FA dimensions and ratios are all significantly larger on the convexity of the major curve and maximal at or close to the apex. Mean thoracic foraminal dimensions change in a predictable manner relative to position on the major thoracic curve. There was no significant correlation with the measured foraminal dimensions or ratios and the potential dependent variables. The average ratio of convexity to concavity dimensions at the apex foramina for entrance, midpoint and exit respectively are FH (1.50, 1.38, 1.25), FW (1.28, 1.30, 0.98), FA (2.06, 1.84, 1.32), P-SAP (1.61, 1.47, 1.30). CONCLUSION Foraminal dimensions of the thoracic spine are significantly affected by AIS. Foraminal dimensions have a predictable convexity to concavity ratio relative to the proximity to the major curve apex. Surgeons should be aware of these anatomical differences during scoliosis correction surgery.

Improved image contrast of the bone-muscle interface with 3T MRI compared to 1.5T MRI [Abstract]

Virtual 3D models of long bones are increasingly being used for implant design and research applications. The current gold standard for the acquisition of such data is Computed Tomography (CT) scanning. Due to radiation exposure, CT is generally limited to the imaging of clinical cases and cadaver specimens. Magnetic Resonance Imaging (MRI) does not involve ionising radiation and therefore can be used to image selected healthy human volunteers for research purposes. The feasibility of MRI as alternative to CT for the acquisition of morphological bone data of the lower extremity has been demonstrated in recent studies [1, 2]. Some of the current limitations of MRI are long scanning times and difficulties with image segmentation in certain anatomical regions due to poor contrast between bone and surrounding muscle tissues. Higher field strength scanners promise to offer faster imaging times or better image quality. In this study image quality at 1.5T is quantitatively compared to images acquired at 3T. --------- The femora of five human volunteers were scanned using 1.5T and 3T MRI scanners from the same manufacturer (Siemens) with similar imaging protocols. A 3D flash sequence was used with TE = 4.66 ms, flip angle = 15° and voxel size = 0.5 × 0.5 × 1 mm. PA-Matrix and body matrix coils were used to cover the lower limb and pelvis respectively. Signal to noise ratio (SNR) [3] and contrast to noise ratio (CNR) [3] of the axial images from the proximal, shaft and distal regions were used to assess the quality of images from the 1.5T and 3T scanners. The SNR was calculated for the muscle and bone-marrow in the axial images. The CNR was calculated for the muscle to cortex and cortex to bone marrow interfaces, respectively. --------- Preliminary results (one volunteer) show that the SNR of muscle for the shaft and distal regions was higher in 3T images (11.65 and 17.60) than 1.5T images (8.12 and 8.11). For the proximal region the SNR of muscles was higher in 1.5T images (7.52) than 3T images (6.78). The SNR of bone marrow was slightly higher in 1.5T images for both proximal and shaft regions, while it was lower in the distal region compared to 3T images. The CNR between muscle and bone of all three regions was higher in 3T images (4.14, 6.55 and 12.99) than in 1.5T images (2.49, 3.25 and 9.89). The CNR between bone-marrow and bone was slightly higher in 1.5T images (4.87, 12.89 and 10.07) compared to 3T images (3.74, 10.83 and 10.15). These results show that the 3T images generated higher contrast between bone and the muscle tissue than the 1.5T images. It is expected that this improvement of image contrast will significantly reduce the time required for the mainly manual segmentation of the MR images. Future work will focus on optimizing the 3T imaging protocol for reducing chemical shift and susceptibility artifacts.

The application of phonetic distribution normalisation to likelihood-maximising speech enhancement for robust ASR

Traditional speech enhancement methods optimise signal-level criteria such as signal-to-noise ratio, but such approaches are sub-optimal for noise-robust speech recognition. Likelihood-maximising (LIMA) frameworks on the other hand, optimise the parameters of speech enhancement algorithms based on state sequences generated by a speech recogniser for utterances of known transcriptions. Previous applications of LIMA frameworks have generated a set of global enhancement parameters for all model states without taking in account the distribution of model occurrence, making optimisation susceptible to favouring frequently occurring models, in particular silence. In this paper, we demonstrate the existence of highly disproportionate phonetic distributions on two corpora with distinct speech tasks, and propose to normalise the influence of each phone based on a priori occurrence probabilities. Likelihood analysis and speech recognition experiments verify this approach for improving ASR performance in noisy environments.

Seasonal Variation in Measured Solar Ultraviolet Radiation Exposure of Adults in Subtropical Australia

Generating accurate population-specific public health messages regarding sun protection requires knowledge about seasonal variation in sun exposure in different environments. To address this issue for a subtropical area of Australia, we used polysulphone badges to measure UVR for the township of Nambour (26° latitude) and personal UVR exposure among Nambour residents who were taking part in a skin cancer prevention trial. Badges were worn by participants for two winter and two summer days. The ambient UVR was approximately three times as high in summer as in winter. However, participants received more than twice the proportion of available UVR in winter as in summer (6.5%vs 2.7%, P < 0.05), resulting in an average ratio of summer to winter personal UVR exposure of 1.35. The average absolute difference in daily dose between summer and winter was only one-seventh of a minimal erythemal dose. Extrapolating from our data, we estimate that ca. 42% of the total exposure received in the 6 months of winter (June–August) and summer (December–February) is received during the three winter months. Our data show that in Queensland a substantial proportion of people’s annual UVR dose is obtained in winter, underscoring the need for dissemination of sun protection messages throughout the year in subtropical and tropical climates.

The use of phase in complex spectrum subtraction for robust speech recognition

In this paper we propose a new method for utilising phase information by complementing it with traditional magnitude-only spectral subtraction speech enhancement through Complex Spectrum Subtraction (CSS). The proposed approach has the following advantages over traditional magnitude-only spectral subtraction: (a) it introduces complementary information to the enhancement algorithm; (b) it reduces the total number of algorithmic parameters, and; (c) is designed for improving clean speech magnitude spectra and is therefore suitable for both automatic speech recognition (ASR) and speech perception applications. Oracle-based ASR experiments verify this approach, showing an average of 20% relative word accuracy improvements when accurate estimates of the phase spectrum are available. Based on sinusoidal analysis and assuming stationarity between observations (which is shown to be better approximated as the frame rate is increased), this paper also proposes a novel method for acquiring the phase information called Phase Estimation via Delay Projection (PEDEP). Further oracle ASR experiments validate the potential for the proposed PEDEP technique in ideal conditions. Realistic implementation of CSS with PEDEP shows performance comparable to state of the art spectral subtraction techniques in a range of 15-20 dB signal-to-noise ratio environments. These results clearly demonstrate the potential for using phase spectra in spectral subtractive enhancement applications, and at the same time highlight the need for deriving more accurate phase estimates in a wider range of noise conditions.

Gas boosted solar water heaters : Queensland case studies of installation practices in new homes

Because of the greenhouse gas emissions implications of the market dominating electric hot water systems, governments in Australia have implemented policies and programs to encourage the uptake of solar water heaters (SWHs) in the residential market as part of climate change adaptation and mitigation strategies. The cost-benefit analysis that usually accompanies all government policy and program design could be simplistically reduced to the ratio of expected greenhouse gas reductions of SWH to the cost of a SWH. The national Register of Solar Water Heaters specifies how many renewable energy certificates (RECs) are allocated to complying SWHs according to their expected performance, and hence greenhouse gas reductions, in different climates. Neither REC allocations nor rebates are tied to actual performance of systems. This paper examines the performance of instantaneous gas-boosted solar water heaters installed in new residences in a housing estate in south-east Queensland in the period 2007 – 2010. The evidence indicates systemic failures in installation practices, resulting in zero solar performance or dramatic underperformance (estimated average 43% solar contribution). The paper will detail the faults identified, and how these faults were eventually diagnosed and corrected. The impacts of these system failures on end-use consumers are discussed before concluding with a brief overview of areas where further research is required in order to more fully understand whole of supply chain implications.