Defining the flammability of cylindrical metal rods through characterization of the thermal effects of the ignition promoter

All relevant international standards for determining if a metallic rod is flammable in oxygen utilize some form of “promoted ignition” test. In this test, for a given pressure, an overwhelming ignition source is coupled to the end of the test sample and the designation flammable or nonflammable is based upon the amount burned, that is, a burn criteria. It is documented that (1) the initial temperature of the test sample affects the burning of the test sample both (a) in regards to the pressure at which the sample will support burning (threshold pressure) and (b) the rate at which the sample is melted (regression rate of the melting interface); and, (2) the igniter used affects the test sample by heating it adjacent to the igniter as ignition occurs. Together, these facts make it necessary to ensure, if a metallic material is to be considered flammable at the conditions tested, that the burn criteria will exclude any region of the test sample that may have undergone preheating during the ignition process. A two-dimensional theoretical model was developed to describe the transient heat transfer occurring and resultant temperatures produced within this system. Several metals (copper, aluminum, iron, and stainless steel) and ignition promoters (magnesium, aluminum, and Pyrofuze®) were evaluated for a range of oxygen pressures between 0.69 MPa (100 psia) and 34.5 MPa (5,000 psia). A MATLAB® program was utilized to solve the developed model that was validated against (1) a published solution for a similar system and (2) against experimental data obtained during actual tests at the National Aeronautics and Space Administration White Sands Test Facility. The validated model successfully predicts temperatures within the test samples with agreement between model and experiment increasing as test pressure increases and/or distance from the promoter increases. Oxygen pressure and test sample thermal diffusivity were shown to have the largest effect on the results. In all cases evaluated, there is no significant preheating (above about 38°C/100°F) occurring at distances greater than 30 mm (1.18 in.) during the time the ignition source is attached to the test sample. This validates a distance of 30 mm (1.18 in.) above the ignition promoter as a burn length upon which a definition of flammable can be based for inclusion in relevant international standards (that is, burning past this length will always be independent of the ignition event for the ignition promoters considered here. KEYWORDS: promoted ignition, metal combustion, heat conduction, thin fin, promoted combustion, burn length, burn criteria, flammability, igniter effects, heat affected zone.

Email advertising : exploratory insights from Finland

Since the advent of the internet, much speculation has ensued regarding its tangible benefits to business. This article looks at the effectiveness of email advertising to promote information to consumers. Within this email promotion context, and using data from a survey of 838 female Finnish consumers of a major international cosmetics brand, we investigate consumer perceptions of email advertising. Specifically, within an exploratory research context we address two research questions: (1) What email advertising factors may influence visits to the company website? and (2) What email advertising factors may influence visits to a physical (i.e., bricks-and-mortar) company sales outlet? Results suggest that email advertisers should strive to generate emails that are perceived as useful. Useful emails appear to influence consumers to visit the store primarily to either buy the product or view the product firsthand, rather than visit the company website. However, as consumers could not buy the advertised products from the website, these findings should be regarded as preliminary. Factors influencing perceptions of email advertising usefulness are explored along with limitations and future research directions.

Determination of burn criterion for promoted combustion testing

Promoted ignition testing [1–3] is used to determine the relative flammability of metal rods in oxygen-enriched atmospheres. In these tests, a promoter is used to ignite each metal rod to start the sample burning. Experiments were performed to better understand the promoted ignition test by obtaining insight into the effect a burning promoter has on the preheating of a test sample. Test samples of several metallic materials were prepared and coupled to fast-responding thermocouples along their length. Various ignition promoters were used to ignite the test samples. The thermocouple measurements and test video were synchronized to determine temperature increase with respect to time and length along each test sample. A recommended length of test sample that must be consumed to be considered a flammable material was determined based on the preheated zone measured from these tests. This length was determined to be 30 mm (1.18 in.). Validation of this length and its rationale are presented.

The power of a single prototype : sustainable fashion textile design and the prevention of carcinogenic melanoma

Is there a role for prototyping (sketching, pattern making and sampling) in addressing real world problems of sustainability (People, Profit, and Planet), in this case social/healthcare issues, through fashion and textiles research? Skin cancer and related illnesses are a major cause of disfigurement and death in New Zealand and Australia where the rates of Melanoma, a serious form of skin cancer, are four times higher than in the Northern Hemisphere regions of USA, UK and Canada (IARC, 1992). In 2007, AUT University (Auckland University of Technology) Fashion Department and the Health Promotion Department of Cancer Society - Auckland Division (CSA) developed a prototype hat aimed at exploring a barrier type solution to prevent facial and neck skin damage. This is a paradigm shift from the usual medical research model. This paper provides an overview of the project and examines how a fashion prototype has been used to communicate emergent social, environmental, personal, physiological and technological concerns to the trans-disciplinary research team. The authors consider how the design of a product can enhance and support sustainable design practice while contributing a potential solution to an ongoing health issue. Analysis of this case study provides an insight into prototyping in fashion and textiles design, user engagement and the importance of requirements analysis in relation to sustainable development. The analysis and a successful outcome of the final prototype have provided a gateway to future collaborative research and product development.

Towards dynamically-favourable quad-rotor aerial robots

This paper outlines progress towards realising practical quad-rotor robot helicopters and, in particular, the Australian National University’s ‘X-4 Flyer’ platform. Two challenges facing the X-4 are generating sufficient thrust and managing unstable dynamic behaviour. We address these issues with a rotor design technique for maximising thrust and the application of a novel rotor mast configuration. An aero-elastic blade design is described and its performance results are presented. A sprung teetering rotor hub that allows adjustment of the blade flapping characteristics and a quad-rotor dynamic model with blade flapping are introduced. The use of inverted rotors is shown to produce favorable stability properties for the Mark II X-4 Flyer.

An alginate-based hybrid system for growth factor delivery in the functional repair of large bone defects

The treatment of challenging fractures and large osseous defects presents a formidable problem for orthopaedic surgeons. Tissue engineering/regenerative medicine approaches seek to solve this problem by delivering osteogenic signals within scaffolding biomaterials. In this study, we introduce a hybrid growth factor delivery system that consists of an electrospun nanofiber mesh tube for guiding bone regeneration combined with peptide-modified alginate hydrogel injected inside the tube for sustained growth factor release. We tested the ability of this system to deliver recombinant bone morphogenetic protein-2 (rhBMP-2) for the repair of critically-sized segmental bone defects in a rat model. Longitudinal [mu]-CT analysis and torsional testing provided quantitative assessment of bone regeneration. Our results indicate that the hybrid delivery system resulted in consistent bony bridging of the challenging bone defects. However, in the absence of rhBMP-2, the use of nanofiber mesh tube and alginate did not result in substantial bone formation. Perforations in the nanofiber mesh accelerated the rhBMP-2 mediated bone repair, and resulted in functional restoration of the regenerated bone. [mu]-CT based angiography indicated that perforations did not significantly affect the revascularization of defects, suggesting that some other interaction with the tissue surrounding the defect such as improved infiltration of osteoprogenitor cells contributed to the observed differences in repair. Overall, our results indicate that the hybrid alginate/nanofiber mesh system is a promising growth factor delivery strategy for the repair of challenging bone injuries.

Bushfire sustainability : Strategies for reconciling bushfire and biodiversity with daily life

This exhibition and catalogue provides a visual record of student work exhibited at the Australian Institute of Architects offices in Brisbane from November 15 to 29, 2010. The exhibition features the final design outcomes of the inaugural Bushfire Sustainability unit conducted at QUT in semester two, 2010. The core objective of this unit was to develop our students’ skills in collaborative practice in design, research and presentation. The theme of ‘bushfire sustainability’ was chosen because living sustainably in bushfire prone landscapes presents a number of problems, the nature of which might only be resolved via multidisciplinary collaboration among the design disciplines. The students involved represent the disciplines of Interior Design, Landscape Architecture, Industrial Design, Architecture and Sustainability – all from within the School of Design at QUT. 55 students, mostly in their third year of study, worked in teams of five (one from each discipline) to design one of a number of homes in highly bushfire prone sites in either Western Australia or SE Queensland. This year level and the interdisciplinary mix are perhaps the best placed to resolve these problems: being unrestrained from the burdens of professional practice and technical overload they retain the potential for innovative, lateral thinking across the range of spatial scales and philosophical perspectives associated with inhabitation of bushfire prone landscapes. It is envisaged that, through the ‘vehicle’ of this design research, that the students’ work will contribute to understandings of how creative design disciplines might respond to this significant national problem, which hitherto has been attended to primarily by engineering and the sciences.

Heat effects of promoters and determination of burn criterion in promoted combustion testing

Promoted ignition testing (NASA) Test 17) [1] is used to determine the relative flammability of metal rods in oxygen-enriched atmospheres. A promotor is used to ignite a metal sample rod, initiating sample burning. If a predetermined length of the sample burns, beyond the promotor, the material is considered flammable at the condition tested. Historically, this burn length has been somewhat arbitrary. Experiments were performed to better understand this test by obtaining insight into the effect a burning promotor has on the preheating of a test sample. Test samples of several metallic materials were prepared and coupled to fast-responding thermocouples along their length. Thermocouple measurements and test video were synchronized to determine temperature increase with respect to time and length along each test sample. A recommended flammability burn length, based on a sample preheat of 500 degrees fahrenheit, was determined based on the preheated zone measured from these tests. This length was determined to be 30 mm (1.18 in.). Validation of this length and its rationale are presented.

Drivers of supply chain collaboration among Finnish manufacturers

This paper focuses on data exchange relationships and ways to improve collaboration in the supply chain. Initially, the paper examines the information needs and alternatives in supply chain management. In the second part, the paper identifies different sets of factors that are likely to influence information sharing with suppliers, from the manufacturers’ point of view. Results from a Finnish Manufacturing industry survey show that manufacturers provided substantial information on demand data, production schedules, and inventories to their suppliers. Respondents perceived delivery performance measured by the timeliness, accuracy, and defect rate of deliveries as the primary incentives for supplier collaboration. On the other hand, supplier image and the market in which the supplier operates were found to be less relevant in determining the intensity of collaboration.