Concurrent multi-scale modeling of civil infrastructures for analyses on structural deteriorating—Part II : Model updating and verification

This paper is a continuation of the paper titled “Concurrent multi-scale modeling of civil infrastructure for analyses on structural deteriorating—Part I: Modeling methodology and strategy” with the emphasis on model updating and verification for the developed concurrent multi-scale model. The sensitivity-based parameter updating method was applied and some important issues such as selection of reference data and model parameters, and model updating procedures on the multi-scale model were investigated based on the sensitivity analysis of the selected model parameters. The experimental modal data as well as static response in terms of component nominal stresses and hot-spot stresses at the concerned locations were used for dynamic response- and static response-oriented model updating, respectively. The updated multi-scale model was further verified to act as the baseline model which is assumed to be finite-element model closest to the real situation of the structure available for the subsequent arbitrary numerical simulation. The comparison of dynamic and static responses between the calculated results by the final model and measured data indicated the updating and verification methods applied in this paper are reliable and accurate for the multi-scale model of frame-like structure. The general procedures of multi-scale model updating and verification were finally proposed for nonlinear physical-based modeling of large civil infrastructure, and it was applied to the model verification of a long-span bridge as an actual engineering practice of the proposed procedures.

Updating and verification for multi-scale finite element model of structure behavior

The method on concurrent multi-scale model of structural behavior (CMSM-of-SB) for the purpose of structural health monitoring including model updating and validating has been studied. The detailed process of model updating and validating is discussed in terms of reduced scale specimen of the steel box girder in longitudinal stiffening truss of a long span bridge. Firstly, some influence factors affecting the accuracy of the CMSM-of-SB including the boundary restraint regidity, the geometry and material parameters on the toe of the weld and its neighbor are analyzed using sensitivity method. Then, sensitivity-based model updating technology is adopted to update the developed CMSM-of-SB and model verification is carried out through calculating and comparing stresses on different locations under various loading from dynamic characteristic and static response. It can be concluded that the CMSM-of-SB based on the substructure method is valid.

Cartographic Strategies of Postmodernity : the Figure of the Map in Contemporary Theory and Fiction

The last fifty years have witnessed the growing pervasiveness of the figure of the map in critical, theoretical, and fictional discourse. References to mapping and cartography are endemic in poststructuralist theory, and, similarly, geographically and culturally diverse authors of twentieth-century fiction seem fixated upon mapping. While the map metaphor has been employed for centuries to highlight issues of textual representation and epistemology, the map metaphor itself has undergone a transformation in the postmodern era. This metamorphosis draws together poststructuralist conceptualizations of epistemology, textuality, cartography, and metaphor, and signals a shift away from modernist preoccupations with temporality and objectivity to a postmodern pragmatics of spatiality and subjectivity. Cartographic Strategies of Postmodernity charts this metamorphosis of cartographic metaphor, and argues that the ongoing reworking of the map metaphor renders it a formative and performative metaphor of postmodernity.

Vibration based baseline updating method to localize crack formation and propagation in reinforced concrete members

Structural Health Monitoring (SHM) schemes are useful for proper management of the performance of structures and for preventing their catastrophic failures. Vibration based SHM schemes has gained popularity during the past two decades resulting in significant research. It is hence evitable that future SHM schemes will include robust and automated vibration based damage assessment techniques (VBDAT) to detect, localize and quantify damage. In this context, the Damage Index (DI) method which is classified as non-model or output based VBDAT, has the ability to automate the damage assessment process without using a computer or numerical model along with actual measurements. Although damage assessment using DI methods have been able to achieve reasonable success for structures made of homogeneous materials such as steel, the same success level has not been reported with respect to Reinforced Concrete (RC) structures. The complexity of flexural cracks is claimed to be the main reason to hinder the applicability of existing DI methods in RC structures. Past research also indicates that use of a constant baseline throughout the damage assessment process undermines the potential of the Modal Strain Energy based Damage Index (MSEDI). To address this situation, this paper presents a novel method that has been developed as part of a comprehensive research project carried out at Queensland University of Technology, Brisbane, Australia. This novel process, referred to as the baseline updating method, continuously updates the baseline and systematically tracks both crack formation and propagation with the ability to automate the damage assessment process using output only data. The proposed method is illustrated through examples and the results demonstrate the capability of the method to achieve the desired outcomes.

Model updating of real structures with ambient vibration data

It is important to develop reliable finite element models for real structures not only in the design phase but also for the structural health monitoring and structural maintenance purposes. This paper describes the experience of the authors in using ambient vibration model identification techniques together with model updating tools to develop reliable finite element models of real civil engineering structures. Case studies of two real structures are presented in this paper. One is a 10 storey concrete building which is considered as a non-slender structure with complex boundary conditions. The other is a single span concrete foot bridge which is also a relatively inflexible planar structure with complex boundary conditions. Both structures are located at the Queensland University of Technology (QUT) and equipped with continuous structural health monitoring systems.

Innovative cartography standards for Web-GIS portals : case study of the 'Survey of Israel's' Web-GIS Portal

Maps have been published on the world wide web since its inception (Cartwright, 1999) and are still accessed and viewed by millions of users today (Peterson, 2003). While early webbased GIS products lacked a complete set of cartographic capabilities, the functionality within such systems has significantly increased over recent years. Functionalities once found only in desktop GIS products are now available in web-based GIS applications, for example, data entry, basic editing, and analysis. Applications based on web-GIS are becoming more widespread and the web-based GIS environment is replacing the traditional desktop GIS platforms in many organizations. Therefore, development of a new cartographic method for web-based GIS is vital. The broad aim of this project is to examine and discuss the challenges and opportunities of innovative cartography methods for web-based GIS platforms. The work introduces a recently developed cartographic methodology, which is based on a web-based GIS portal by the Survey of Israel (SOI). The work discusses the prospects and constraints of such methods in improving web-GIS interfaces and usability for the end user. The work also tables the preliminary findings of the initial implementation of the web-based GIS cartographic method within the portal of the Survey of Israel, as well as the applicability of those methods elsewhere.

Adaptive unsupervised learning of human actions

Automatic detection of suspicious activities in CCTV camera feeds is crucial to the success of video surveillance systems. Such a capability can help transform the dumb CCTV cameras into smart surveillance tools for fighting crime and terror. Learning and classification of basic human actions is a precursor to detecting suspicious activities. Most of the current approaches rely on a non-realistic assumption that a complete dataset of normal human actions is available. This paper presents a different approach to deal with the problem of understanding human actions in video when no prior information is available. This is achieved by working with an incomplete dataset of basic actions which are continuously updated. Initially, all video segments are represented by Bags-Of-Words (BOW) method using only Term Frequency-Inverse Document Frequency (TF-IDF) features. Then, a data-stream clustering algorithm is applied for updating the system's knowledge from the incoming video feeds. Finally, all the actions are classified into different sets. Experiments and comparisons are conducted on the well known Weizmann and KTH datasets to show the efficacy of the proposed approach.

A comparative study of manufacturing practices and performance variables

The reported study was conducted to compare and contrast current manufacturing practices between two countries, Australia and Malaysia, and identify the practices that significantly influence their manufacturing performances. The results are based on data collected from surveys using a standard questionnaire in both countries. Evidence indicates that product quality and reliability is the main competitive factor for manufacturers. Maintaining a supplier rating system and regularly updating it with field failure and warranty data and making use of product data management are found to be effective manufacturing practices. In terms of the investigated manufacturing performance, Australian manufacturers are marginally ahead of their Malaysian counterparts. However, Malaysian manufacturers came out ahead on most dimensions of advanced quality and manufacturing practices, particularly in the adoption of product data management, effective supply chains and relationships with suppliers and customers.

Bearing-only SLAM : a vision-based navigation system for autonomous robots

To navigate successfully in a previously unexplored environment, a mobile robot must be able to estimate the spatial relationships of the objects of interest accurately. A Simultaneous Localization and Mapping (SLAM) sys- tem employs its sensors to build incrementally a map of its surroundings and to localize itself in the map simultaneously. The aim of this research project is to develop a SLAM system suitable for self propelled household lawnmowers. The proposed bearing-only SLAM system requires only an omnidirec- tional camera and some inexpensive landmarks. The main advantage of an omnidirectional camera is the panoramic view of all the landmarks in the scene. Placing landmarks in a lawn field to define the working domain is much easier and more flexible than installing the perimeter wire required by existing autonomous lawnmowers. The common approach of existing bearing-only SLAM methods relies on a motion model for predicting the robot’s pose and a sensor model for updating the pose. In the motion model, the error on the estimates of object positions is cumulated due mainly to the wheel slippage. Quantifying accu- rately the uncertainty of object positions is a fundamental requirement. In bearing-only SLAM, the Probability Density Function (PDF) of landmark position should be uniform along the observed bearing. Existing methods that approximate the PDF with a Gaussian estimation do not satisfy this uniformity requirement. This thesis introduces both geometric and proba- bilistic methods to address the above problems. The main novel contribu- tions of this thesis are: 1. A bearing-only SLAM method not requiring odometry. The proposed method relies solely on the sensor model (landmark bearings only) without relying on the motion model (odometry). The uncertainty of the estimated landmark positions depends on the vision error only, instead of the combination of both odometry and vision errors. 2. The transformation of the spatial uncertainty of objects. This thesis introduces a novel method for translating the spatial un- certainty of objects estimated from a moving frame attached to the robot into the global frame attached to the static landmarks in the environment. 3. The characterization of an improved PDF for representing landmark position in bearing-only SLAM. The proposed PDF is expressed in polar coordinates, and the marginal probability on range is constrained to be uniform. Compared to the PDF estimated from a mixture of Gaussians, the PDF developed here has far fewer parameters and can be easily adopted in a probabilistic framework, such as a particle filtering system. The main advantages of our proposed bearing-only SLAM system are its lower production cost and flexibility of use. The proposed system can be adopted in other domestic robots as well, such as vacuum cleaners or robotic toys when terrain is essentially 2D.

Boys 'doing' and 'undoing' media education : new possibilities for theory and practice

The purpose of this study is to investigate how secondary school media educators might best meet the needs of students who prefer practical production work to ‘theory’ work in media studies classrooms. This is a significant problem for a curriculum area that claims to develop students’ media literacies by providing them with critical frameworks and a metalanguage for thinking about the media. It is a problem that seems to have become more urgent with the availability of new media technologies and forms like video games. The study is located in the field of media education, which tends to draw on structuralist understandings of the relationships between young people and media and suggests that students can be empowered to resist media’s persuasive discourses. Recent theoretical developments suggest too little emphasis has been placed on the participatory aspects of young people playing with, creating and gaining pleasure from media. This study contributes to this ‘participatory’ approach by bringing post structuralist perspectives to the field, which have been absent from studies of secondary school media education. I suggest theories of media learning must take account of the ongoing formation of students’ subjectivities as they negotiate social, cultural and educational norms. Michel Foucault’s theory of ‘technologies of the self’ and Judith Butler’s theories of performativity and recognition are used to develop an argument that media learning occurs in the context of students negotiating various ‘ethical systems’ as they establish their social viability through achieving recognition within communities of practice. The concept of ‘ethical systems’ has been developed for this study by drawing on Foucault’s theories of discourse and ‘truth regimes’ and Butler’s updating of Althusser’s theory of interpellation. This post structuralist approach makes it possible to investigate the ways in which students productively repeat and vary norms to creatively ‘do’ and ‘undo’ the various media learning activities with which they are required to engage. The study focuses on a group of year ten students in an all boys’ Catholic urban school in Australia who undertook learning about video games in a three-week intensive ‘immersion’ program. The analysis examines the ethical systems operating in the classroom, including formal systems of schooling, informal systems of popular cultural practice and systems of masculinity. It also examines the students’ use of semiotic resources to repeat and/or vary norms while reflecting on, discussing, designing and producing video games. The key findings of the study are that students are motivated to learn technology skills and production processes rather than ‘theory’ work. This motivation stems from the students’ desire to become recognisable in communities of technological and masculine practice. However, student agency is not only possible through critical responses to media, but through performative variation of norms through creative ethical practices as students participate with new media technologies. Therefore, the opportunities exist for media educators to create the conditions for variation of norms through production activities. The study offers several implications for media education theory and practice including: the productive possibilities of post structuralism for informing ways of doing media education; the importance of media teachers having the autonomy to creatively plan curriculum; the advantages of media and technology teachers collaborating to draw on a broad range of resources to develop curriculum; the benefits of placing more emphasis on students’ creative uses of media; and the advantages of blending formal classroom approaches to media education with less formal out of school experiences.

Which way up? Reading and drawing maps of the blogosphere

Mapping the physical world, the arrangement of continents and oceans, cities and villages, mountains and deserts, while not without its own contentious aspects, can at least draw upon centuries of previous work in cartography and discovery. To map virtual spaces is another challenge altogether. Are cartographic conventions applicable to depictions of the blogosphere, or the internet in general? Is a more mathematical approach required to even start to make sense of the shape of the blogosphere, to understand the network created by and between blogs? With my research comparing information flows in the Australian and French political blogs, visualising the data obtained is important as it can demonstrate the spread of ideas and topics across blogs. However, how best to depict the flows, links, and the spaces between is still unclear. Is network theory and systems of hubs and nodes more relevant than mass communication theories to the research at hand, influencing the nature of any map produced? Is it even a good idea to try and apply boundaries like ‘Australian’ and ‘French’ to parts of a map that does not reflect international borders or the Mercator projection? While drawing upon some of my work-in-progress, this paper will also evaluate previous maps of the blogosphere and approaches to depicting networks of blogs. As such, the paper will provide a greater awareness of the tools available and the strengths and limitations of mapping methodologies, helping to shape the direction of my research in a field still very much under development.

Many Mount Barrens

Cibachrome photographic prints, Digital print, Acrylic Sheet , wire & card.--------- Total size: 170cm x 119cm x 15cm---------- The work employs a terrestrial photography and cartographic technique to represent a diversity of landscape types surrounding West Mt Barren in Western Australia. Sixteen views of West Mt Barren were captured over a two week period from map grid coordinates in the surround landscape. These images are configured in Many Mount Barrens in a manner which corresponds to the position from which they were recorded.---------- The work was exhibited at Eyes wide open (curators K Bradby and A Brandenberg) which was held at Gorepani Gallery, Albany WA to coincide with the first national screening on SBS Television of the Western Australian documentary A Million Acres a Year (Rijavec, F, Harrison, N & Bradby K (directors), Snakewood Films & Film Australia, c2003).

Canopy dweller

This article discusses the renovation of a house located in western Brisbane, Queensland, originally designed by architects Lindsay and Kerry Clare and now renovated by architect Stuart Vokes of Owen and Vokes. Features of the renovation include keeping the Queenslander style while updating with new timber finishing, white painted surfaces, opening up living areas and designing a new kitchen.

Tracking road edges in the panospheric image plane

This paper presents a technique for tracking road edges in a panoramic image sequence. The major contribution is that instead of unwarping the image to find parallel lines representing the road edges, we choose to warp the parallel groundplane lines into the image plane of the equiangular panospheric camera. Updating the parameters of the line thus involves searching a very small number of pixels in the panoramic image, requiring considerably less computation than unwarping. Results using real-world images, including shadows, intersections and curves, are presented.

A vibration based method to update axial shortening of load bearing elements

Axial shortening in vertical load bearing elements of reinforced concrete high-rise buildings is caused by the time dependent effects of shrinkage, creep and elastic shortening of concrete under loads. Such phenomenon has to be predicted at design stage and then updated during and after construction of the buildings in order to provide mitigation against the adverse effects of differential axial shortening among the elements. Existing measuring methods for updating previous predictions of axial shortening pose problems. With this in mind, a innovative procedure with a vibration based parameter called axial shortening index is proposed to update axial shortening of vertical elements based on variations in vibration characteristics of the buildings. This paper presents the development of the procedure and illustrates it through a numerical example of an unsymmetrical high-rise building with two outrigger and belt systems. Results indicate that the method has the capability to capture influence of different tributary areas, shear walls of outrigger and belt systems as well as the geometric complexity of the building.