An investigation of rail condition monitoring by Fibre Bragg Grating sensors

Condition monitoring on rails and train wheels is vitally important to the railway asset management and the rail-wheel interactions provide the crucial information of the health state of both rails and wheels. Continuous and remote monitoring is always a preference for operators. With a new generation of strain sensing devices in Fibre Bragg Grating (FBG) sensors, this study explores the possibility of continuous monitoring of the health state of the rails; and investigates the required signal processing techniques and their limitations.

Householder experiences with resource monitoring technology in sustainable homes

The use of feedback technologies, in the form of products such as Smart Meters, is increasingly seen as the means by which 'consumers' can be made aware of their patterns of resource consumption, and to then use this enhanced awareness to change their behaviour to reduce the environmental impacts of their consumption. These technologies tend to be single-resource focused (e.g. on electricity consumption only) and their functionality defined by persons other than end-users (e.g. electricity utilities). This paper presents initial findings of end-users' experiences with a multi-resource feedback technology, within the context of sustainable housing. It proposes that an understanding of user context, supply chain management and market diffusion issues are important design considerations that contribute to technology 'success'.

On-board mass monitoring of heavy vehicles : results of testing program

The Transport Certification Australia on-board mass feasibility project is testing various on-board mass devices in a range of heavy vehicles (HVs). Extensive field tests of on-board mass measurement systems for HVs have been conducted during 2008. These tests were of accuracy, robustness and tamper-evidence of heavy vehicle on-board mass telematics. All the systems tested showed accuracies within approximately +/- 500 kg of gross combination mass or approximately +/- 2% of the attendant weighbridge reading. Analysis of the dynamic data also showed encouraging results and has raised the possibility of use of such dynamic information in tamper evidence in two areas. This analysis was to determine if the use of averaged dynamic data could identify potential tampering or incorrect operating procedures as well as the possibility of dynamic measurements flagging a tamper event by the use of metrics including a tampering index (TIX). Technical and business options to detect tamper events will now be developed during implementation of regulatory OBM system application to Australian heavy vehicles (HVs).

Monitoring of the vertical movements of rail sleepers with the passage of trains

Due to an ever increasing demand for more frequent and higher volume of train service, the physical conditions of tracks in modem railways are deteriorating more quickly when compared to tracks built decades ago. There are incidences in both the UK and Hong Kong indicating there are needs for a more stringent checks on the rail conditions using suitable and effective non-invasive and nondestructive condition monitoring system.

A comprehensive condition monitoring of modern railway

The demand for high quality rail services in the twenty-first century has put an ever increasing demand on all rail operators. In order to meet the expectation of their patrons, the maintenance regime of railway systems has to be tightened up, the track conditions have to be well looked after, the rolling stock must be designed to withstand heavy duty. In short, in an ideal world where resources are unlimited, one needs to implement a very rigorous inspection regime in order to take care of the modem needs of a railway system [1]. If cost were not an issue, the maintenance engineers could inspect the train body by the most up-to-date techniques such as ultra-sound examination, x-ray inspection, magnetic particle inspection, etc. on a regular basis. However it is inconceivable to have such a perfect maintenance regime in any commercial railway. Likewise, it is impossible to have a perfect rolling stock which can weather all the heavy duties experienced in a modem railway. Hence it is essential that some condition monitoring schemes are devised to pick up potential defects which could manifest into safety hazards. This paper introduces an innovative condition monitoring system for track profile and, together with an instrumented car to carry out surveillance of the track, will provide a comprehensive railway condition monitoring system which is free from the usual difficulty of electromagnetic compatibility issues in a typical railway environment

Study of acoustic emission data analysis tools for structural health monitoring applications

Acoustic emission (AE) technique is one of the popular diagnostic techniques used for structural health monitoring of mechanical, aerospace and civil structures. But several challenges still exist in successful application of AE technique. This paper explores various tools for analysis of recorded AE data to address two primary challenges: discriminating spurious signals from genuine signals and devising ways to quantify damage levels.

Structural health monitoring of bridges : source localisation in acoustic emission technique

Managing the sustainability of urban infrastructure requires regular health monitoring of key infrastructure such as bridges. The process of structural health monitoring involves monitoring a structure over a period of time using appropriate sensors, extracting damage sensitive features from the measurements made by the sensors, and analysing these features to determine the current state of the structure. Various techniques are available for structural health monitoring of structures, and acoustic emission is one technique that is finding an increasing use in the monitoring of civil infrastructures such as bridges. Acoustic emission technique is based on the recording of stress waves generated by rapid release of energy inside a material, followed by analysis of recorded signals to locate and identify the source of emission and assess its severity. This chapter first provides a brief background of the acoustic emission technique and the process of source localization. Results from laboratory experiments conducted to explore several aspects of the source localization process are also presented. The findings from the study can be expected to enhance knowledge of the acoustic emission process, and to aid the development of effective bridge structure diagnostics systems.

Photo-cross-linked poly(D,L-lactide)-based networks. Structural characterization by HR-MAS NMR spectroscopy and hydrolytic degradation behavior

To date, biodegradable networks and particularly their kinetic chain lengths have been characterized by analysis of their degradation products in solution. We characterize the network itself by NMR analysis in the solvent-swollen state under magic angle spinning conditions. The networks were prepared by photoinitiated cross-linking of poly(dl-lactide)−dimethacrylate macromers (5 kg/mol) in the presence of an unreactive diluent. Using diffusion filtering and 2D correlation spectroscopy techniques, all network components are identified. By quantification of network-bound photoinitiator fragments, an average kinetic chain length of 9 ± 2 methacrylate units is determined. The PDLLA macromer solution was also used with a dye to prepare computer-designed structures by stereolithography. For these networks structures, the average kinetic chain length is 24 ± 4 methacrylate units. In all cases the calculated molecular weights of the polymethacrylate chains after degradation are maximally 8.8 kg/mol, which is far below the threshold for renal clearance. Upon incubation in phosphate buffered saline at 37 °C, the networks show a similar mass loss profile in time as linear high-molecular-weight PDLLA (HMW PDLLA). The mechanical properties are preserved longer for the PDLLA networks than for HMW PDLLA. The initial tensile strength of 47 ± 2 MPa does not decrease significantly for the first 15 weeks, while HMW PDLLA lost 85 ± 5% of its strength within 5 weeks. The physical properties, kinetic chain length, and degradation profile of these photo-cross-linked PDLLA networks make them most suited materials for orthopedic applications and use in (bone) tissue engineering.

Diesel engine condition monitoring and simulated diesel knock

This paper discusses diesel engine condition monitoring (CM) using acoustic emissions (AE) as well as some of the commonly encountered diesel engine problems. Also discussed are some of the underlying combustion related faults and the methods used in past studies to simulate diesel engine faults. The initial test involved an experimental simulation of two common combustion related diesel engine faults, namely diesel knock and misfire. These simulated faults represent the first step towards a comprehensive investigation and analysis into the characteristics of acoustic emission signals arising from combustion related diesel engine faults. Data corresponding to different engine running conditions was captured using in-cylinder pressure, vibration and acoustic emission transducers along with both crank angle encoder and top-dead centre (TDC) signals. Using these signals, it was possible to characterise the effect of different combustion conditions and hence, various diesel engine in-cylinder pressure profiles.

A regulatory on-board mass monitoring application for heavy vehicles in Australia

This paper reports on the development of specifications for an on-board mass monitoring (OBM) application for regulatory requirements in Australia. An earlier paper reported on feasibility study and pilot testing program prior to the specification development [1]. Learnings from the pilot were used to refine this testing process and a full scale testing program was conducted from July to October 2008. The results from the full scale test and evidentiary implications are presented in this report. The draft specification for an evidentiary on-board mass monitoring application is currently under development.

Dynamics of pattern writing and erasure in photorefractive lithium niobate for data storage applications

The present rate of technological advance continues to place significant demands on data storage devices. The sheer amount of digital data being generated each year along with consumer expectations, fuels these demands. At present, most digital data is stored magnetically, in the form of hard disk drives or on magnetic tape. The increase in areal density (AD) of magnetic hard disk drives over the past 50 years has been of the order of 100 million times, and current devices are storing data at ADs of the order of hundreds of gigabits per square inch. However, it has been known for some time that the progress in this form of data storage is approaching fundamental limits. The main limitation relates to the lower size limit that an individual bit can have for stable storage. Various techniques for overcoming these fundamental limits are currently the focus of considerable research effort. Most attempt to improve current data storage methods, or modify these slightly for higher density storage. Alternatively, three dimensional optical data storage is a promising field for the information storage needs of the future, offering very high density, high speed memory. There are two ways in which data may be recorded in a three dimensional optical medium; either bit-by-bit (similar in principle to an optical disc medium such as CD or DVD) or by using pages of bit data. Bit-by-bit techniques for three dimensional storage offer high density but are inherently slow due to the serial nature of data access. Page-based techniques, where a two-dimensional page of data bits is written in one write operation, can offer significantly higher data rates, due to their parallel nature. Holographic Data Storage (HDS) is one such page-oriented optical memory technique. This field of research has been active for several decades, but with few commercial products presently available. Another page-oriented optical memory technique involves recording pages of data as phase masks in a photorefractive medium. A photorefractive material is one by which the refractive index can be modified by light of the appropriate wavelength and intensity, and this property can be used to store information in these materials. In phase mask storage, two dimensional pages of data are recorded into a photorefractive crystal, as refractive index changes in the medium. A low-intensity readout beam propagating through the medium will have its intensity profile modified by these refractive index changes and a CCD camera can be used to monitor the readout beam, and thus read the stored data. The main aim of this research was to investigate data storage using phase masks in the photorefractive crystal, lithium niobate (LiNbO3). Firstly the experimental methods for storing the two dimensional pages of data (a set of vertical stripes of varying lengths) in the medium are presented. The laser beam used for writing, whose intensity profile is modified by an amplitudemask which contains a pattern of the information to be stored, illuminates the lithium niobate crystal and the photorefractive effect causes the patterns to be stored as refractive index changes in the medium. These patterns are read out non-destructively using a low intensity probe beam and a CCD camera. A common complication of information storage in photorefractive crystals is the issue of destructive readout. This is a problem particularly for holographic data storage, where the readout beam should be at the same wavelength as the beam used for writing. Since the charge carriers in the medium are still sensitive to the read light field, the readout beam erases the stored information. A method to avoid this is by using thermal fixing. Here the photorefractive medium is heated to temperatures above 150�C; this process forms an ionic grating in the medium. This ionic grating is insensitive to the readout beam and therefore the information is not erased during readout. A non-contact method for determining temperature change in a lithium niobate crystal is presented in this thesis. The temperature-dependent birefringent properties of the medium cause intensity oscillations to be observed for a beam propagating through the medium during a change in temperature. It is shown that each oscillation corresponds to a particular temperature change, and by counting the number of oscillations observed, the temperature change of the medium can be deduced. The presented technique for measuring temperature change could easily be applied to a situation where thermal fixing of data in a photorefractive medium is required. Furthermore, by using an expanded beam and monitoring the intensity oscillations over a wide region, it is shown that the temperature in various locations of the crystal can be monitored simultaneously. This technique could be used to deduce temperature gradients in the medium. It is shown that the three dimensional nature of the recording medium causes interesting degradation effects to occur when the patterns are written for a longer-than-optimal time. This degradation results in the splitting of the vertical stripes in the data pattern, and for long writing exposure times this process can result in the complete deterioration of the information in the medium. It is shown in that simply by using incoherent illumination, the original pattern can be recovered from the degraded state. The reason for the recovery is that the refractive index changes causing the degradation are of a smaller magnitude since they are induced by the write field components scattered from the written structures. During incoherent erasure, the lower magnitude refractive index changes are neutralised first, allowing the original pattern to be recovered. The degradation process is shown to be reversed during the recovery process, and a simple relationship is found relating the time at which particular features appear during degradation and recovery. A further outcome of this work is that the minimum stripe width of 30 ìm is required for accurate storage and recovery of the information in the medium, any size smaller than this results in incomplete recovery. The degradation and recovery process could be applied to an application in image scrambling or cryptography for optical information storage. A two dimensional numerical model based on the finite-difference beam propagation method (FD-BPM) is presented and used to gain insight into the pattern storage process. The model shows that the degradation of the patterns is due to the complicated path taken by the write beam as it propagates through the crystal, and in particular the scattering of this beam from the induced refractive index structures in the medium. The model indicates that the highest quality pattern storage would be achieved with a thin 0.5 mm medium; however this type of medium would also remove the degradation property of the patterns and the subsequent recovery process. To overcome the simplistic treatment of the refractive index change in the FD-BPM model, a fully three dimensional photorefractive model developed by Devaux is presented. This model shows significant insight into the pattern storage, particularly for the degradation and recovery process, and confirms the theory that the recovery of the degraded patterns is possible since the refractive index changes responsible for the degradation are of a smaller magnitude. Finally, detailed analysis of the pattern formation and degradation dynamics for periodic patterns of various periodicities is presented. It is shown that stripe widths in the write beam of greater than 150 ìm result in the formation of different types of refractive index changes, compared with the stripes of smaller widths. As a result, it is shown that the pattern storage method discussed in this thesis has an upper feature size limit of 150 ìm, for accurate and reliable pattern storage.

Advances in vegetation management for power line corridor monitoring using aerial remote sensing techniques

This paper presents a comprehensive discussion of vegetation management approaches in power line corridors based on aerial remote sensing techniques. We address three issues 1) strategies for risk management in power line corridors, 2) selection of suitable platforms and sensor suite for data collection and 3) the progress in automated data processing techniques for vegetation management. We present initial results from a series of experiments and, challenges and lessons learnt from our project.

Analysis of acoustic emission data for structural health monitoring applications

Acoustic emission (AE) is the phenomenon where high frequency stress waves are generated by rapid release of energy within a material by sources such as crack initiation or growth. AE technique involves recording these stress waves by means of sensors placed on the surface and subsequent analysis of the recorded signals to gather information such as the nature and location of the source. It is one of the several diagnostic techniques currently used for structural health monitoring (SHM) of civil infrastructure such as bridges. Some of its advantages include ability to provide continuous in-situ monitoring and high sensitivity to crack activity. But several challenges still exist. Due to high sampling rate required for data capture, large amount of data is generated during AE testing. This is further complicated by the presence of a number of spurious sources that can produce AE signals which can then mask desired signals. Hence, an effective data analysis strategy is needed to achieve source discrimination. This also becomes important for long term monitoring applications in order to avoid massive date overload. Analysis of frequency contents of recorded AE signals together with the use of pattern recognition algorithms are some of the advanced and promising data analysis approaches for source discrimination. This paper explores the use of various signal processing tools for analysis of experimental data, with an overall aim of finding an improved method for source identification and discrimination, with particular focus on monitoring of steel bridges.

Application of acoustic emission technology in monitoring structure integrity of bridges

Bridges are an important part of a nation’s infrastructure and reliable monitoring methods are necessary to ensure their safety and efficiency. Most bridges in use today were built decades ago and are now subjected to changes in load patterns that can cause localized distress, which can result in bridge failure if not corrected. Early detection of damage helps in prolonging lives of bridges and preventing catastrophic failures. This paper briefly reviews the various technologies currently used in health monitoring of bridge structures and in particular discusses the application and challenges of acoustic emission (AE) technology. Some of the results from laboratory experiments on a bridge model are also presented. The main objectives of these experiments are source localisation and assessment. The findings of the study can be expected to enhance the knowledge of acoustic emission process and thereby aid in the development of an effective bridge structure diagnostics system.

Monitoring and regulatory role of the balanced scorecard in controlling organisational identities

This thesis employs the theoretical fusion of disciplinary knowledge, interlacing an analysis from both functional and interpretive frameworks and applies these paradigms to three concepts—organisational identity, the balanced scorecard performance measurement system, and control. As an applied thesis, this study highlights how particular public sector organisations are using a range of multi-disciplinary forms of knowledge constructed for their needs to achieve practical outcomes. Practical evidence of this study is not bound by a single disciplinary field or the concerns raised by academics about the rigorous application of academic knowledge. The study’s value lies in its ability to explore how current communication and accounting knowledge is being used for practical purposes in organisational life. The main focus of this thesis is on identities in an organisational communication context. In exploring the theoretical and practical challenges, the research questions for this thesis were formulated as: 1. Is it possible to effectively control identities in organisations by the use of an integrated performance measurement system—the balanced scorecard—and if so, how? 2. What is the relationship between identities and an integrated performance measurement system—the balanced scorecard—in the identity construction process? Identities in the organisational context have been extensively discussed in graphic design, corporate communication and marketing, strategic management, organisational behaviour, and social psychology literatures. Corporate identity is the self-presentation of the personality of an organisation (Van Riel, 1995; Van Riel & Balmer, 1997), and organisational identity is the statement of central characteristics described by members (Albert & Whetten, 2003). In this study, identity management is positioned as a strategically complex task, embracing not only logo and name, but also multiple dimensions, levels and facets of organisational life. Responding to the collaborative efforts of researchers and practitioners in identity conceptualisation and methodological approaches, this dissertation argues that analysis can be achieved through the use of an integrated framework of identity products, patternings and processes (Cornelissen, Haslam, & Balmer, 2007), transforming conceptualisations of corporate identity, organisational identity and identification studies. Likewise, the performance measurement literature from the accounting field now emphasises the importance of ‘soft’ non-financial measures in gauging performance—potentially allowing the monitoring and regulation of ‘collective’ identities (Cornelissen et al., 2007). The balanced scorecard (BSC) (Kaplan & Norton, 1996a), as the selected integrated performance measurement system, quantifies organisational performance under the four perspectives of finance, customer, internal process, and learning and growth. Broadening the traditional performance measurement boundary, the BSC transforms how organisations perceived themselves (Vaivio, 2007). The rhetorical and communicative value of the BSC has also been emphasised in organisational self-understanding (Malina, Nørreklit, & Selto, 2007; Malmi, 2001; Norreklit, 2000, 2003). Thus, this study establishes a theoretical connection between the controlling effects of the BSC and organisational identity construction. Common to both literatures, the aspects of control became the focus of this dissertation, as ‘the exercise or act of achieving a goal’ (Tompkins & Cheney, 1985, p. 180). This study explores not only traditional technical and bureaucratic control (Edwards, 1981), but also concertive control (Tompkins & Cheney, 1985), shifting the locus of control to employees who make their own decisions towards desired organisational premises (Simon, 1976). The controlling effects on collective identities are explored through the lens of the rhetorical frames mobilised through the power of organisational enthymemes (Tompkins & Cheney, 1985) and identification processes (Ashforth, Harrison, & Corley, 2008). In operationalising the concept of control, two guiding questions were developed to support the research questions: 1.1 How does the use of the balanced scorecard monitor identities in public sector organisations? 1.2 How does the use of the balanced scorecard regulate identities in public sector organisations? This study adopts qualitative multiple case studies using ethnographic techniques. Data were gathered from interviews of 41 managers, organisational documents, and participant observation from 2003 to 2008, to inform an understanding of organisational practices and members’ perceptions in the five cases of two public sector organisations in Australia. Drawing on the functional and interpretive paradigms, the effective design and use of the systems, as well as the understanding of shared meanings of identities and identifications are simultaneously recognised. The analytical structure guided by the ‘bracketing’ (Lewis & Grimes, 1999) and ‘interplay’ strategies (Schultz & Hatch, 1996) preserved, connected and contrasted the unique findings from the multi-paradigms. The ‘temporal bracketing’ strategy (Langley, 1999) from the process view supports the comparative exploration of the analysis over the periods under study. The findings suggest that the effective use of the BSC can monitor and regulate identity products, patternings and processes. In monitoring identities, the flexible BSC framework allowed the case study organisations to monitor various aspects of finance, customer, improvement and organisational capability that included identity dimensions. Such inclusion legitimises identity management as organisational performance. In regulating identities, the use of the BSC created a mechanism to form collective identities by articulating various perspectives and causal linkages, and through the cascading and alignment of multiple scorecards. The BSC—directly reflecting organisationally valued premises and legitimised symbols—acted as an identity product of communication, visual symbols and behavioural guidance. The selective promotion of the BSC measures filtered organisational focus to shape unique identity multiplicity and characteristics within the cases. Further, the use of the BSC facilitated the assimilation of multiple identities by controlling the direction and strength of identifications, engaging different groups of members. More specifically, the tight authority of the BSC framework and systems are explained both by technical and bureaucratic controls, while subtle communication of organisational premises and information filtering is achieved through concertive control. This study confirms that these macro top-down controls mediated the sensebreaking and sensegiving process of organisational identification, supporting research by Ashforth, Harrison and Corley (2008). This study pays attention to members’ power of self-regulation, filling minor premises of the derived logic of their organisation through the playing out of organisational enthymemes (Tompkins & Cheney, 1985). Members are then encouraged to make their own decisions towards the organisational premises embedded in the BSC, through the micro bottom-up identification processes including: enacting organisationally valued identities; sensemaking; and the construction of identity narratives aligned with those organisationally valued premises. Within the process, the self-referential effect of communication encouraged members to believe the organisational messages embedded in the BSC in transforming collective and individual identities. Therefore, communication through the use of the BSC continued the self-producing of normative performance mechanisms, established meanings of identities, and enabled members’ self-regulation in identity construction. Further, this research establishes the relationship between identity and the use of the BSC in terms of identity multiplicity and attributes. The BSC framework constrained and enabled case study organisations and members to monitor and regulate identity multiplicity across a number of dimensions, levels and facets. The use of the BSC constantly heightened the identity attributes of distinctiveness, relativity, visibility, fluidity and manageability in identity construction over time. Overall, this research explains the reciprocal controlling relationships of multiple structures in organisations to achieve a goal. It bridges the gap among corporate and organisational identity theories by adopting Cornelissen, Haslam and Balmer’s (2007) integrated identity framework, and reduces the gap in understanding between identity and performance measurement studies. Parallel review of the process of monitoring and regulating identities from both literatures synthesised the theoretical strengths of both to conceptualise and operationalise identities. This study extends the discussion on positioning identity, culture, commitment, and image and reputation measures in integrated performance measurement systems as organisational capital. Further, this study applies understanding of the multiple forms of control (Edwards, 1979; Tompkins & Cheney, 1985), emphasising the power of organisational members in identification processes, using the notion of rhetorical organisational enthymemes. This highlights the value of the collaborative theoretical power of identity, communication and performance measurement frameworks. These case studies provide practical insights about the public sector where existing bureaucracy and desired organisational identity directions are competing within a large organisational setting. Further research on personal identity and simple control in organisations that fully cascade the BSC down to individual members would provide enriched data. The extended application of the conceptual framework to other public and private sector organisations with a longitudinal view will also contribute to further theory building.