An experimental research investigation into disused flat rail wagons as bridges with applications for low volume rural roads in Australia

An experimental laboratory investigation was carried out to assess the structural adequacy of a disused PHO Class Flat Bottom Rail Wagon (FRW) for a single lane low volume road bridge application as per the design provisions of the Australian Bridge Design Standard AS 5100(2004). The investigation also encompassed a review into the risk associated with the pre-existing damage in wagons incurred during their service life on rail. The main objective of the laboratory testing of the FRW was to physically measure its performance under the same applied traffic loading it would be required to resist as a road bridge deck. In order to achieve this a full width (5.2m) single lane, single span (approximately 10m), simply supported bridge would be required to be constructed and tested in a structural laboratory. However, the available clear spacing between the columns of the loading portal frame encountered within the laboratory was insufficient to accommodate the 5.2m wide bridge deck excluding clearance normally considered necessary in structural testing. Therefore, only half of the full scale bridge deck (single FRW of width 2.6m) was able to be accommodated and tested; with the continuity of the bridge deck in the lateral direction applied as boundary constraints along the full length of the FRW at six selected locations. This represents a novel approach not yet reported in the literature for bridge deck testing to the best of the knowledge of the author. The test was carried out under two loadings provided in AS 5100 (2004) – one stationary W80 wheel load and the second a moving axle load M1600. As the bridge investigated in the study is a single lane single span low volume road bridge, the risk of pre-existing damage and the expected high cycle fatigue failure potential was assessed as being minimal and hence the bridge deck was not tested structurally for fatigue/ fracture. The high axle load requirements have instead been focussed upon the investigation into the serviceability and ultimate limit state requirements. The testing regime adopted however involved extensive recording of strains and deflections at several critical locations of the FRW. Three locations of W80 point load and two locations of the M1600 Axle load were considered for the serviceability testing; the FRW was also tested under the ultimate load dictated by the M1600. The outcomes of the experimental investigation have demonstrated that the FRW is structurally adequate to resist the prescribed traffic loadings outlaid in AS 5100 (2004). As the loading was directly applied on to the FRW, the laboratory testing is assessed as being significantly conservative. The FRW bridge deck in the field would only resist the load transferred by the running platform, where, depending on the design, composite action might exist – thereby the share of the loading which needs to be resisted by the FRW would be smaller than the system tested in the lab. On this basis, a demonstration bridge is under construction at the time of writing this thesis and future research will involve field testing in order to assess its performance.

Quantification of the accuracy of MRI generated 3D models of long bones compared to CT generated 3D models

Orthopaedic fracture fixation implants are increasingly being designed using accurate 3D models of long bones based on computer tomography (CT). Unlike CT, magnetic resonance imaging (MRI) does not involve ionising radiation and is therefore a desirable alternative to CT. This study aims to quantify the accuracy of MRI-based 3D models compared to CT-based 3D models of long bones. The femora of five intact cadaver ovine limbs were scanned using a 1.5T MRI and a CT scanner. Image segmentation of CT and MRI data was performed using a multi-threshold segmentation method. Reference models were generated by digitising the bone surfaces free of soft tissue with a mechanical contact scanner. The MRI- and CT-derived models were validated against the reference models. The results demonstrated that the CT-based models contained an average error of 0.15mm while the MRI-based models contained an average error of 0.23mm. Statistical validation shows that there are no significant differences between 3D models based on CT and MRI data. These results indicate that the geometric accuracy of MRI based 3D models was comparable to that of CT-based models and therefore MRI is a potential alternative to CT for generation of 3D models with high geometric accuracy.

Stochastic chemical kinetics and the quasi-steady-state assumption : application to the stochastic simulation algorithm and chemical master equation

Recently the application of the quasi-steady-state approximation (QSSA) to the stochastic simulation algorithm (SSA) was suggested for the purpose of speeding up stochastic simulations of chemical systems that involve both relatively fast and slow chemical reactions [Rao and Arkin, J. Chem. Phys. 118, 4999 (2003)] and further work has led to the nested and slow-scale SSA. Improved numerical efficiency is obtained by respecting the vastly different time scales characterizing the system and then by advancing only the slow reactions exactly, based on a suitable approximation to the fast reactions. We considerably extend these works by applying the QSSA to numerical methods for the direct solution of the chemical master equation (CME) and, in particular, to the finite state projection algorithm [Munsky and Khammash, J. Chem. Phys. 124, 044104 (2006)], in conjunction with Krylov methods. In addition, we point out some important connections to the literature on the (deterministic) total QSSA (tQSSA) and place the stochastic analogue of the QSSA within the more general framework of aggregation of Markov processes. We demonstrate the new methods on four examples: Michaelis–Menten enzyme kinetics, double phosphorylation, the Goldbeter–Koshland switch, and the mitogen activated protein kinase cascade. Overall, we report dramatic improvements by applying the tQSSA to the CME solver.

The nature and prevalence of inter-organizational project ventures : evidence from a large scale field study in the Netherlands 2006-2009

There has recently been noted a rapid increase in research attention to projects that involve outside partners. Our knowledge of such inter-organizational projects, however, is limited. This paper reports large scale data from a repeated trend survey amongst 2000 SMEs in 2006 and 2009 that focused on inter-organizational project ventures. Our major findings indicate that the overall prevalence of inter-organizational project ventures remained significant and stable over time, even despite the economic crisis. Moreover, we find that these ventures predominantly solve repetitive rather than unique tasks and are embedded in prior relations between the partnering organizations. These findings provide empirical support for the recent claims that project management should pay more attention to inter-organizational forms of project organization, and suggest that the archetypical view of projects as being unique in every respect should be reconsidered. Both have important implications for project management, especially in the area of project-based learning.

Parallel implementation of stochastic simulation for large scale cellular processes

Experimental and theoretical studies have shown the importance of stochastic processes in genetic regulatory networks and cellular processes. Cellular networks and genetic circuits often involve small numbers of key proteins such as transcriptional factors and signaling proteins. In recent years stochastic models have been used successfully for studying noise in biological pathways, and stochastic modelling of biological systems has become a very important research field in computational biology. One of the challenge problems in this field is the reduction of the huge computing time in stochastic simulations. Based on the system of the mitogen-activated protein kinase cascade that is activated by epidermal growth factor, this work give a parallel implementation by using OpenMP and parallelism across the simulation. Special attention is paid to the independence of the generated random numbers in parallel computing, that is a key criterion for the success of stochastic simulations. Numerical results indicate that parallel computers can be used as an efficient tool for simulating the dynamics of large-scale genetic regulatory networks and cellular processes

The Global Youth Media Council : young people speaking and learning about media reform

The 5th World Summit on Media for Children and Youth held in Karlstad, Sweden in June 2010 provided a unique media literacy experience for approximately thirty young people from diverse backgrounds through participation in the Global Youth Media Council. This article focuses on the Summit’s aim to give young people a ‘voice’ through intercultural dialogue about media reform. The accounts of four young Australians are discussed in order to consider how successful the Summit was in achieving this goal. The article concludes by making recommendations for future international media literacy conferences involving young people. It also advocates for the expansion of the Global Youth Media Council concept as a grass roots movement to involve more young people in discussions about media reform.

Walking when intoxicated : an investigation of the factors which influence individuals' drink walking intentions

Annually, in Australia, 10-15% of all road-related fatalities involve pedestrians. Of those pedestrians fatally injured, approximately 45% were walking while intoxicated or 'drink walking'. Drink walking is increasing in prevalence and younger persons may be especially prone to engage in this behaviour and, thus, are at heightened risk of being injured or killed. Presently, limited research is available regarding the factors which influence individuals to drink walk. This study explored young people's (17-25 years) intentions to drink walk, using an extended Theory of Planned Behaviour (TPB). Participants (N = 215), completed a self-report questionnaire which assessed the standard TPB constructs (attitude, subjective norm, perceived behavioural control) as well as the extended constructs of risk perception, anticipated regret, and past behaviour. It was hypothesised that the standard TPB constructs would significantly predict individuals' reported intentions to drink walk and that the additional constructs would predict intentions over and above the TPB constructs. The TPB variables significantly predicted 63.2% of the variance in individuals' reported intentions to drink walk, and the additional variables, combined, explained a further 6.1% of the variance. Of the additional constructs, anticipated regret and past behaviour, but not risk perception, were significant predictors of drink walking intentions. As one of the first studies to provide a theoretically-based investigation of factors influencing individuals' drink walking intentions, the current study's findings have potentially significant implications for understanding young people's decisions to drink walk and the design of future countermeasures to ultimately reduce this behaviour.

The flammability of metallic materials in normal and reduced gravity

Metallic materials exposed to oxygen-enriched atmospheres – as commonly used in the medical, aerospace, aviation and numerous chemical processing industries – represent a significant fire hazard which must be addressed during design, maintenance and operation. Hence, accurate knowledge of metallic materials flammability is required. Reduced gravity (i.e. space-based) operations present additional unique concerns, where the absence of gravity must also be taken into account. The flammability of metallic materials has historically been quantified using three standardised test methods developed by NASA, ASTM and ISO. These tests typically involve the forceful (promoted) ignition of a test sample (typically a 3.2 mm diameter cylindrical rod) in pressurised oxygen. A test sample is defined as flammable when it undergoes burning that is independent of the ignition process utilised. In the standardised tests, this is indicated by the propagation of burning further than a defined amount, or „burn criterion.. The burn criterion in use at the onset of this project was arbitrarily selected, and did not accurately reflect the length a sample must burn in order to be burning independent of the ignition event and, in some cases, required complete consumption of the test sample for a metallic material to be considered flammable. It has been demonstrated that a) a metallic material.s propensity to support burning is altered by any increase in test sample temperature greater than ~250-300 oC and b) promoted ignition causes an increase in temperature of the test sample in the region closest to the igniter, a region referred to as the Heat Affected Zone (HAZ). If a test sample continues to burn past the HAZ (where the HAZ is defined as the region of the test sample above the igniter that undergoes an increase in temperature of greater than or equal to 250 oC by the end of the ignition event), it is burning independent of the igniter, and should be considered flammable. The extent of the HAZ, therefore, can be used to justify the selection of the burn criterion. A two dimensional mathematical model was developed in order to predict the extent of the HAZ created in a standard test sample by a typical igniter. The model was validated against previous theoretical and experimental work performed in collaboration with NASA, and then used to predict the extent of the HAZ for different metallic materials in several configurations. The extent of HAZ predicted varied significantly, ranging from ~2-27 mm depending on the test sample thermal properties and test conditions (i.e. pressure). The magnitude of the HAZ was found to increase with increasing thermal diffusivity, and decreasing pressure (due to slower ignition times). Based upon the findings of this work, a new burn criterion requiring 30 mm of the test sample to be consumed (from the top of the ignition promoter) was recommended and validated. This new burn criterion was subsequently included in the latest revision of the ASTM G124 and NASA 6001B international test standards that are used to evaluate metallic material flammability in oxygen. These revisions also have the added benefit of enabling the conduct of reduced gravity metallic material flammability testing in strict accordance with the ASTM G124 standard, allowing measurement and comparison of the relative flammability (i.e. Lowest Burn Pressure (LBP), Highest No-Burn Pressure (HNBP) and average Regression Rate of the Melting Interface(RRMI)) of metallic materials in normal and reduced gravity, as well as determination of the applicability of normal gravity test results to reduced gravity use environments. This is important, as currently most space-based applications will typically use normal gravity information in order to qualify systems and/or components for reduced gravity use. This is shown here to be non-conservative for metallic materials which are more flammable in reduced gravity. The flammability of two metallic materials, Inconel® 718 and 316 stainless steel (both commonly used to manufacture components for oxygen service in both terrestrial and space-based systems) was evaluated in normal and reduced gravity using the new ASTM G124-10 test standard. This allowed direct comparison of the flammability of the two metallic materials in normal gravity and reduced gravity respectively. The results of this work clearly show, for the first time, that metallic materials are more flammable in reduced gravity than in normal gravity when testing is conducted as described in the ASTM G124-10 test standard. This was shown to be the case in terms of both higher regression rates (i.e. faster consumption of the test sample – fuel), and burning at lower pressures in reduced gravity. Specifically, it was found that the LBP for 3.2 mm diameter Inconel® 718 and 316 stainless steel test samples decreased by 50% from 3.45 MPa (500 psia) in normal gravity to 1.72 MPa (250 psia) in reduced gravity for the Inconel® 718, and 25% from 3.45 MPa (500 psia) in normal gravity to 2.76 MPa (400 psia) in reduced gravity for the 316 stainless steel. The average RRMI increased by factors of 2.2 (27.2 mm/s in 2.24 MPa (325 psia) oxygen in reduced gravity compared to 12.8 mm/s in 4.48 MPa (650 psia) oxygen in normal gravity) for the Inconel® 718 and 1.6 (15.0 mm/s in 2.76 MPa (400 psia) oxygen in reduced gravity compared to 9.5 mm/s in 5.17 MPa (750 psia) oxygen in normal gravity) for the 316 stainless steel. Reasons for the increased flammability of metallic materials in reduced gravity compared to normal gravity are discussed, based upon the observations made during reduced gravity testing and previous work. Finally, the implications (for fire safety and engineering applications) of these results are presented and discussed, in particular, examining methods for mitigating the risk of a fire in reduced gravity.

Planning for SMEs’ Proactive Waste Management in Office Building Retrofit Projects

Office building retrofit projects face many challenges for on-site waste management. While the projects themselves have the potential for a significant level of reuse and recycling from decon-struction and demolition, their unique characteristics often prohibit direct application of existing waste management systems, which are typically based on managing waste generated through new material application in new build projects. Moreover, current waste management plans include no stimuli to involve Small and Medium Enterprises (SMEs) for on-site waste management. As SMEs carry out the majority of on-site work as subcontractors, their active involvements will result in more proactive approaches to waste management and enhance project delivery. This paper discusses the interim results of a continuing research aimed at engaging SMEs in the planning processes of waste management through the collaboration between subcontractors and main contractors of retrofitting projects. It introduces a conceptual model for SMEs to proactively plan and manage on-site waste generation for both deconstruction and construction stages, before traditional waste management plans by the main contractor come into place. The model also suggests a collaboration process between SMEs as subcontractors and large companies as the main contractor to improve the involvement and performance of SMEs in waste management of office building retrofit projects.

Fitting in : a pervasive new graduate nurse need

Aim: This qualitative study aims to provide insight into how Australian New Graduate Nurses (NGNs) experienced their transition to acute care nursing practice. Method: Nine NGNs each participated in three in-depth interviews conducted across their first year of practice. Constant comparative analysis was used to identify the emergent themes. Findings: The desire to fit in (establishment of secure social bonds) with ward staff is an important element of NGN transition experiences. Fitting in was about feeling one's self to be part of a social group, and participants made it clear that their perceptions of their success in establishing secure and meaningful social bonds in each new ward was extremely important for their sense of being as NGNs. Current NGN Transition Programmes (NGNTPs) involve multiple ward rotations, increasing the demand for the NGN to fit in. Thus participants were engaged in a deeply personal transition experience that was not necessarily aligned with multiple ward rotations. Conclusions: Although NGNTPs have the word “transition” in their title, it may be that current programmes are more focussed on organisations’ desire to “orient” NGNs to working within the acute care setting than facilitating personal transitions to practice. Further investigation of the impact of NGNTPs on NGNs and the associated multiple ward rotations is required.

Social influences on Chinese drivers : cultural context and traffic law enforcement

Reducing road crashes and associated trauma is a critical focus as the Decade of Action for Road Safety commences. China is one of many rapidly-motorizing nations to experience recent increases in private-vehicle ownership and an associated escalation in novice drivers. Unfortunately, however, China also experiences a high rate of death and injury from road crashes. Several key pieces of legislation have been introduced in recent decades in China to deal with these changes. While managing the legal aspects of road use is important, social influences on driver behaviour may offer additional avenues for promoting safe driving, particularly in a culture where such factors carry high importance. To date, there is limited research on the role of social influence factors on driver behaviour in China, yet we know that Chinese society is strongly based on social rules, customs, and relationships. There is reason to assume therefore, that road use and driving-related issues may also be strongly influenced by social relationships. One previous study that has investigated such issues highlighted the need to consider culturally-specific issues such as interpersonal networks and social hierarchy when examining driver behaviour in China (Xie & Parker, 2002). Those authors suggested that there are some concepts relating to Chinese driving culture that may not necessarily have been identified from research conducted in western contexts and that research conducted in China must be considered in light of such concepts. The current paper reports qualitative research conducted with Beijing drivers to investigate such social influence factors. Findings indicated that family members, friends, and driving instructors appear influential on driver behaviour and that some novice drivers seek additional assistance after obtaining their licence. The finding relating to the influence of driving instructors was not surprising, given the substantial number of new drivers in China. In Beijing, driving instruction is conducted off-road in purpose-specific driving facilities rather than on the road network. Once licensed, it is common for new drivers to have little or no experience driving in complex traffic situations. This learning situation is unlikely to provide all the skills necessary to successfully negotiate crowded city streets and assess the related risk associated with such driving. Therefore, it was not surprising to find that one reported strategy to assist new drivers was to employ the services of an ‘accompanying driver’ to provide ongoing driving instruction once licensed. In more highly motorised countries supervised practice is part of a graduated licensing system where it is compulsory for new drivers to be supervised by a more experienced driver for a requisite period of time before progressing to solo driving. However, as this system is not in place in China, it appears that some drivers seek out and pay for additional support once they commence on-road driving. Additionally, strategies to avoid detection and penalties for inappropriate road use were discussed, many of which involve the use of a third person. These findings indicate potential barriers to implementing effective traffic enforcement and highlight the importance of understanding culturally-specific social factors relating to driver behaviour.

Iron biogeochemistry and associated greenhouse gas evolution in a forested subtropical Australian coastal catchment : Poona Creek, Southeast Queensland

Iron (Fe) is the fourth most abundant element in the Earth’s crust. Excess Fe mobilization from terrestrial into aquatic systems is of concern for deterioration of water quality via biofouling and nuisance algal blooms in coastal and marine systems. Substantial Fe dissolution and transport involve alternate Fe(II) oxidation followed by Fe(III) reduction, with a diversity of Bacteria and Archaea acting as the key catalyst. Microbially-mediated Fe cycling is of global significance with regard to cycles of carbon (C), sulfur (S) and manganese (Mn). However, knowledge regarding microbial Fe cycling in circumneutral-pH habitats that prevail on Earth has been lacking until recently. In particular, little is known regarding microbial function in Fe cycling and associated Fe mobilization and greenhouse (CO2 and CH4, GHG) evolution in subtropical Australian coastal systems where microbial response to ambient variations such as seasonal flooding and land use changes is of concern. Using the plantation-forested Poona Creek catchment on the Fraser Coast of Southeast Queensland (SEQ), this research aimed to 1) study Fe cycling-associated bacterial populations in diverse terrestrial and aquatic habitats of a representative subtropical coastal circumneutral-pH (4–7) ecosystem; and 2) assess potential impacts of Pinus plantation forestry practices on microbially-mediated Fe mobilization, organic C mineralization and associated GHG evolution in coastal SEQ. A combination of wet-chemical extraction, undisturbed core microcosm, laboratory bacterial cultivation, microscopy and 16S rRNA-based molecular phylogenetic techniques were employed. The study area consisted primarily of loamy sands, with low organic C and dissolved nutrients. Total reactive Fe was abundant and evenly distributed within soil 0–30 cm profiles. Organic complexation primarily controlled Fe bioavailability and forms in well-drained plantation soils and water-logged, native riparian soils, whereas tidal flushing exerted a strong “seawater effect” in estuarine locations and formed a large proportion of inorganic Fe(III) complexes. There was a lack of Fe(II) sources across the catchment terrestrial system. Mature, first-rotation plantation clear-felling and second-rotation replanting significantly decreased organic matter and poorly crystalline Fe in well-drained soils, although variations in labile soil organic C fractions (dissolved organic C, DOC; and microbial biomass C, MBC) were minor. Both well-drained plantation soils and water-logged, native-vegetation soils were inhabited by a variety of cultivable, chemotrophic bacterial populations capable of C, Fe, S and Mn metabolism via lithotrophic or heterotrophic, (micro)aerobic or anaerobic pathways. Neutrophilic Fe(III)-reducing bacteria (FeRB) were most abundant, followed by aerobic, heterotrophic bacteria (heterotrophic plate count, HPC). Despite an abundance of FeRB, cultivable Fe(II)-oxidizing bacteria (FeOB) were absent in associated soils. A lack of links between cultivable Fe, S or Mn bacterial densities and relevant chemical measurements (except for HPC correlated with DOC) was likely due to complex biogeochemical interactions. Neither did variations in cultivable bacterial densities correlate with plantation forestry practices, despite total cultivable bacterial densities being significantly lower in estuarine soils when compared with well-drained plantation soils and water-logged, riparian native-vegetation soils. Given that bacterial Fe(III) reduction is the primary mechanism of Fe oxide dissolution in soils upon saturation, associated Fe mobilization involved several abiotic and biological processes. Abiotic oxidation of dissolved Fe(II) by Mn appeared to control Fe transport and inhibit Fe dissolution from mature, first-rotation plantation soils post-saturation. Such an effect was not observed in clear-felled and replanted soils associated with low SOM and potentially low Mn reactivity. Associated GHG evolution post-saturation mainly involved variable CO2 emissions, with low, but consistently increasing CH4 effluxes in mature, first-rotation plantation soil only. In comparison, water-logged soils in the riparian native-vegetation buffer zone functioned as an important GHG source, with high potentials for Fe mobilization and GHG, particularly CH4 emissions in riparian loam soils associated with high clay and crystalline Fe fractions. Active Fe–C cycling was unlikely to occur in lower-catchment estuarine soils associated with low cultivable bacterial densities and GHG effluxes. As a key component of bacterial Fe cycling, neutrophilic FeOB widely occurred in diverse aquatic, but not terrestrial, habitats of the catchment study area. Stalked and sheathed FeOB resembling Gallionella and Leptothrix were limited to microbial mat material deposited in surface fresh waters associated with a circumneutral-pH seep, and clay-rich soil within riparian buffer zones. Unicellular, Sideroxydans-related FeOB (96% sequence identity) were ubiquitous in surface and subsurface freshwater environments, with highest abundance in estuary-adjacent shallow coastal groundwater water associated with redox transition. The abundance of dissolved C and Fe in the groundwater-dependent system was associated with high numbers of cultivable anaerobic, heterotrophic FeRB, microaerophilic, putatively lithotrophic FeOB and aerobic, heterotrophic bacteria. This research represents the first study of microbial Fe cycling in diverse circumneutral-pH environments (terrestrial–aquatic, freshwater–estuarine, surface–subsurface) of a subtropical coastal ecosystem. It also represents the first study of its kind in the southern hemisphere. This work highlights the significance of bacterial Fe(III) reduction in terrestrial, and bacterial Fe(II) oxidation in aquatic catchment Fe cycling. Results indicate the risk of promotion of Fe mobilization due to plantation clear-felling and replanting, and GHG emissions associated with seasonal water-logging. Additional significant outcomes were also achieved. The first direct evidence for multiple biomineralization patterns of neutrophilic, microaerophilic, unicellular FeOB was presented. A putatively pure culture, which represents the first cultivable neutrophilic FeOB from the southern hemisphere, was obtained as representative FeOB ubiquitous in diverse catchment aquatic habitats.

Researching intuitive interaction

Intuitive interaction is based on past experience and is fast and often non conscious. We have conducted ten studies into this issue over the past ten years, involving more than 400 participants. Data collection methods have included questionnaires, interviews, observations, concurrent and retrospective protocols, and cognitive measures. Coding schemes have been developed to suit each study and involve robust, literature based heuristics. Some other researchers have investigated this issue and their methods are also examined. The paper traces the development of the methods and compares the various approaches used over the years.

The Commercial Surrogacy Dilemma

In November 2009 the England and Wales High Court (Family Division) granted a parental order pursuant to s30 Human Fertilisation and Embryology Act 1990 in respect of twins who came to be in the custody and control of the applicants (Mr and Mrs A) through a surrogacy arrangement. The particularly unusual and interesting aspect of this case is that, on the evidence, Mr and Mrs A had paid expenses to the surrogate above and beyond those allowed by the legislation, thus creating a commercial surrogacy arrangement. Commercial surrogacy arrangements involve the payment of money to the surrogate mother in excess of those expenses which have been reasonably incurred pursuant to the surrogacy arrangement. This case is relevant to Queensland law because commercial surrogacy arrangements are also prohibited in Queensland and, as in the United Kingdom, the court cannot make a parentage order unless it is satisfied the surrogacy arrangement is not a commercial surrogacy arrangement.

Weight management and its role in breast cancer rehabilitation

Overweight and obesity are risk factors for post-menopausal breast cancer, and many women diagnosed with breast cancer, irrespective of menopausal status, gain weight after diagnosis. Weight management plays an important role in rehabilitation and recovery since obesity and/or weight gain may lead to poorer breast cancer prognosis, as well as prevalent co-morbid conditions (e.g. cardiovascular disease and diabetes), poorer surgical outcomes (e.g., increased operating and recovery times, higher infection rates, and poorer healing), lymphedema, fatigue, functional decline, and poorer health and overall quality of life. Health care professionals should encourage weight management at all phases of the cancer care continuum as a means to potentially avoid adverse sequelae and late effects, as well as to improve overall health and possibly survival. Comprehensive approaches that involve dietary and behavior modification, and increased aerobic and strength training exercise have shown promise in either preventing weight gain or promoting weight loss, reducing biomarkers associated with inflammation and co-morbidity, and improving lifestyle behaviors, functional status, and quality of life in this high-risk patient population.