Numerical and experimental studies of cold-formed steel floor systems under standard fire conditions

Light gauge cold-formed steel frame (LSF) structures are increasingly used in industrial, commercial and residential buildings because of their non-combustibility, dimensional stability, and ease of installation. A floor-ceiling system is an example of its applications. LSF floor-ceiling systems must be designed to serve as fire compartment boundaries and provide adequate fire resistance. Fire rated floor-ceiling assemblies formed with new materials and construction methodologies have been increasingly used in buildings. However, limited research has been undertaken in the past and hence a thorough understanding of their fire resistance behaviour is not available. Recently a new composite panel in which an external insulation layer is used between two plasterboards has been developed at QUT to provide a higher fire rating to LSF floors under standard fire conditions. But its increased fire rating could not be determined using the currently available design methods. Research on LSF floor systems under fire conditions is relatively recent and the behaviour of floor joists and other components in the systems is not fully understood. The present design methods thus require the use of expensive fire protection materials to protect them from excessive heat increase during a fire. This leads to uneconomical and conservative designs. Fire rating of these floor systems is provided simply by adding more plasterboard sheets to the steel joists and such an approach is totally inefficient. Hence a detailed fire research study was undertaken into the structural and thermal performance of LSF floor systems including those protected by the new composite panel system using full scale fire tests and extensive numerical studies. Experimental study included both the conventional and the new steel floor-ceiling systems under structural and fire loads using a gas furnace designed to deliver heat in accordance with the standard time- temperature curve in AS 1530.4 (SA, 2005). Fire tests included the behavioural and deflection characteristics of LSF floor joists until failure as well as related time-temperature measurements across the section and along the length of all the specimens. Full scale fire tests have shown that the structural and thermal performance of externally insulated LSF floor system was superior than traditional LSF floors with or without cavity insulation. Therefore this research recommends the use of the new composite panel system for cold-formed LSF floor-ceiling systems. The numerical analyses of LSF floor joists were undertaken using the finite element program ABAQUS based on the measured time-temperature profiles obtained from fire tests under both steady state and transient state conditions. Mechanical properties at elevated temperatures were considered based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). Finite element models were calibrated using the full scale test results and used to further provide a detailed understanding of the structural fire behaviour of the LSF floor-ceiling systems. The models also confirmed the superior performance of the new composite panel system. The validated model was then used in a detailed parametric study. Fire tests and the numerical studies showed that plasterboards provided sufficient lateral restraint to LSF floor joists until their failure. Hence only the section moment capacity of LSF floor joists subjected to local buckling effects was considered in this research. To predict the section moment capacity at elevated temperatures, the effective section modulus of joists at ambient temperature is generally considered adequate. However, this research has shown that it leads to considerable over- estimation of the local buckling capacity of joist subject to non-uniform temperature distributions under fire conditions. Therefore new simplified fire design rules were proposed for LSF floor joist to determine the section moment capacity at elevated temperature based on AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The accuracy of the proposed fire design rules was verified with finite element analysis results. A spread sheet based design tool was also developed based on these design rules to predict the failure load ratio versus time, moment capacity versus time and temperature for various LSF floor configurations. Idealised time-temperature profiles of LSF floor joists were developed based on fire test measurements. They were used in the detailed parametric study to fully understand the structural and fire behaviour of LSF floor panels. Simple design rules were also proposed to predict both critical average joist temperatures and failure times (fire rating) of LSF floor systems with various floor configurations and structural parameters under any given load ratio. Findings from this research have led to a comprehensive understanding of the structural and fire behaviour of LSF floor systems including those protected by the new composite panel, and simple design methods. These design rules were proposed within the guidelines of the Australian/New Zealand, American and European cold- formed steel structures standard codes of practice. These may also lead to further improvements to fire resistance through suitable modifications to the current composite panel system.

Numerical studies of gypsum plasterboard panels under standard fire conditions

Gypsum plasterboards are commonly used as a fire safety material in the building industry. Many research studies have been undertaken to investigate the thermal behaviour of plasterboards under standard fire conditions. However, there are many discrepancies in relation to the basic thermal properties of plasterboards while simple equations are not available to predict the ambient surface time–temperature profiles of gypsum plasterboard panels that can be used in simulating the behaviour and strength of steel studs or joists in load bearing LSF wall and floor systems. In this research, suitable thermal properties of plasterboards were proposed based on a series of tests and available results from past research. Finite element models of gypsum plasterboard panels were then developed to simulate their thermal behaviour under standard fire conditions. The accuracy of the proposed thermal properties and the finite element models was validated by comparing the numerical results with available fire test results of plasterboard panels. This paper presents the details of the finite element models of plasterboard panels, the thermal analysis results from finite element analyses under standard fire conditions and their comparisons with experimental results

Disaster triage : evidence, consistency and standard practice

Triage has military origins, with the initial purpose being to direct care to those most likely to be able to return to the battlefield. Conversely, modern disaster triage attempts to ensure both the prioritisation of care for those who need it most and a fair distribution of resources, so that health responders are able to ‘do the most for the most’...

Service convenience and social servicescape : retail vs hedonic setting

Purpose – While there have been numerous studies on the antecedents and consequences of service quality, there has been little investigation of the moderators of service quality. The purpose of this study is to demonstrate the effects of two moderators: service convenience and the social servicescape. The moderating effects are tested in two service settings: retail and hedonic (concert). Design/methodology/approach – A survey of 270 customers at kitchen display showrooms and 320 concert-goers was undertaken. The results were analysed using regression analysis. Findings – The results show support for ten of the 12 hypotheses. Service convenience moderated the relationships between perceived service quality and its three sub-dimensions (interaction, environment, and outcome quality), differently in different settings (retail vs hedonic). This supports the authors' general argument that the outcome dimension tends to be more important to customers in a retail setting, while interaction and environment quality dimensions tend to be more important in hedonic service consumption. Practical implications – These findings suggest that managers need to use different service management tactics in retail and hedonic service settings. Specifically managers in retail settings need to pay more attention to service convenience to achieve service quality and managers in hedonic settings should concentrate on the social servicescape. Originality/value – This paper is the first to test the moderating factors of service convenience and social servicescape on service quality.

Exeter short stems compared with standard length Exeter stems : experience from the Australian Orthopaedic Association National Joint Replacement Registry

The standard Exeter stem has a length of 150mm with offsets 37.5mm to 56mm. Shorter stems of lengths 95mm, 115mm and 125mm with offsets 35.5mm or less are available for patients with smaller femurs. Concern has been raised regarding the behaviour of the smaller implants. This paper analysed data from the Australian Orthopaedic Association National Joint Replacement Registry comparing survivorship of stems of offset 35.5mm or less with the standard stems of 37.5mm offset or greater. At seven years there was no significant difference in the Cumulative Percent Revision Rate in the short stems (3.4%, 95% CI 2.4-4.8%) compared with the standard length stems (3.5%, 95% CI 3.3-3.8%) despite its use in a greater proportion of potentially more difficult developmental dysplasia of the hip cases.

Food consumption of Sri Lankan adults : an appraisal of serving characteristics

Objective The main aim of the present study was to identify food consumption in Sri Lankan adults based on serving characteristics. Design Cross-sectional study. Fruits, vegetables, starch, meat, pulses, dairy products and added sugars in the diet were assessed with portion sizes estimated using standard methods. Setting Twelve randomly selected clusters from the Sri Lanka Diabetes and Cardiovascular Study. Subjects Six hundred non-institutionalized adults. Results The daily intake of fruit (0·43), vegetable (1·73) and dairy (0·39) portions were well below national recommendations. Only 3·5 % of adults consumed the recommended 5 portions of fruits and vegetables/d; over a third of the population consumed no dairy products and fewer than 1 % of adults consumed 2 portions/d. In contrast, Sri Lankan adults consumed over 14 portions of starch and 3·5 portions of added sugars daily. Almost 70 % of those studied exceeded the upper limit of the recommendations for starch intake. The total daily number of meat and pulse portions was 2·78. Conclusions Dietary guidelines emphasize the importance of a balanced and varied diet; however, a substantial proportion of the Sri Lankan population studied failed to achieve such a recommendation. Nutrition-related diseases in the country may be closely correlated with unhealthy eating habits.

Tax evasion, inequality, and progressive taxes : a political economy perspective

The standard approach to tax compliance applies the economics-of-crime methodology pioneered by Becker (1968): in its first application, due to Allingham and Sandmo (1972) it models the behaviour of agents as a decision involving a choice of the extent of their income to report to tax authorities, given a certain institutional environment, represented by parameters such as the probability of detection and penalties in the event the agent is caught. While this basic framework yields important insights on tax compliance behavior, it has some critical limitations. Specifically, it indicates a level of compliance that is significantly below what is observed in the data. This thesis revisits the original framework with a view towards addressing this issue, and examining the political economy implications of tax evasion for progressivity in the tax structure. The approach followed involves building a macroeconomic, dynamic equilibrium model for the purpose of examining these issues, by using a step-wise model building procedure starting with some very simple variations of the basic Allingham and Sandmo construct, which are eventually integrated to a dynamic general equilibrium overlapping generations framework with heterogeneous agents. One of the variations involves incorporating the Allingham and Sandmo construct into a two-period model of a small open economy of the type originally attributed to Fisher (1930). A further variation of this simple construct involves allowing agents to initially decide whether to evade taxes or not. In the event they decide to evade, the agents then have to decide the extent of income or wealth they wish to under-report. We find that the ‘evade or not’ assumption has strikingly different and more realistic implications for the extent of evasion, and demonstrate that it is a more appropriate modeling strategy in the context of macroeconomic models, which are essentially dynamic in nature, and involve consumption smoothing across time and across various states of nature. Specifically, since deciding to undertake tax evasion impacts on the consumption smoothing ability of the agent by creating two states of nature in which the agent is ‘caught’ or ‘not caught’, there is a possibility that their utility under certainty, when they choose not to evade, is higher than the expected utility obtained when they choose to evade. Furthermore, the simple two-period model incorporating an ‘evade or not’ choice can be used to demonstrate some strikingly different political economy implications relative to its Allingham and Sandmo counterpart. In variations of the two models that allow for voting on the tax parameter, we find that agents typically choose to vote for a high degree of progressivity by choosing the highest available tax rate from the menu of choices available to them. There is, however, a small range of inequality levels for which agents in the ‘evade or not’ model vote for a relatively low value of the tax rate. The final steps in the model building procedure involve grafting the two-period models with a political economy choice into a dynamic overlapping generations setting with more general, non-linear tax schedules and a ‘cost-of evasion’ function that is increasing in the extent of evasion. Results based on numerical simulations of these models show further improvement in the model’s ability to match empirically plausible levels of tax evasion. In addition, the differences between the political economy implications of the ‘evade or not’ version of the model and its Allingham and Sandmo counterpart are now very striking; there is now a large range of values of the inequality parameter for which agents in the ‘evade or not’ model vote for a low degree of progressivity. This is because, in the ‘evade or not’ version of the model, low values of the tax rate encourages a large number of agents to choose the ‘not-evade’ option, so that the redistributive mechanism is more ‘efficient’ relative to the situations in which tax rates are high. Some further implications of the models of this thesis relate to whether variations in the level of inequality, and parameters such as the probability of detection and penalties for tax evasion matter for the political economy results. We find that (i) the political economy outcomes for the tax rate are quite insensitive to changes in inequality, and (ii) the voting outcomes change in non-monotonic ways in response to changes in the probability of detection and penalty rates. Specifically, the model suggests that changes in inequality should not matter, although the political outcome for the tax rate for a given level of inequality is conditional on whether there is a large or small or large extent of evasion in the economy. We conclude that further theoretical research into macroeconomic models of tax evasion is required to identify the structural relationships underpinning the link between inequality and redistribution in the presence of tax evasion. The models of this thesis provide a necessary first step in that direction.

Preparing for portfolio careers in Australian music : setting a research agenda

In the twenty-first century, Australian musicians increasingly maintain ‘portfolio’ careers, in which they combine diverse employment arrangements and activities. Often, these incorporate industry sectors outside of music. This career pattern is widespread but not well understood, largely because of the limitations of existing research. The lack of knowledge about musicians’ work and careers means that Australia currently may not provide appropriate and effective policy, funding, initial training and continuing career support across the diverse music sector. This article discusses existing research relating to the careers and skilling needs of musicians in Australia, and outlines a targeted agenda for further research that has the potential to inform stronger alignment between the requirements of building sustainable music careers and musicians’ education and training.

Setting up a platform for plant-based influenza virus vaccine production in South Africa

Background During a global influenza pandemic, the vaccine requirements of developing countries can surpass their supply capabilities, if these exist at all, compelling them to rely on developed countries for stocks that may not be available in time. There is thus a need for developing countries in general to produce their own pandemic and possibly seasonal influenza vaccines. Here we describe the development of a plant-based platform for producing influenza vaccines locally, in South Africa. Plant-produced influenza vaccine candidates are quicker to develop and potentially cheaper than egg-produced influenza vaccines, and their production can be rapidly upscaled. In this study, we investigated the feasibility of producing a vaccine to the highly pathogenic avian influenza A subtype H5N1 virus, the most generally virulent influenza virus identified to date. Two variants of the haemagglutinin (HA) surface glycoprotein gene were synthesised for optimum expression in plants: these were the full-length HA gene (H5) and a truncated form lacking the transmembrane domain (H5tr). The genes were cloned into a panel of Agrobacterium tumefaciens binary plant expression vectors in order to test HA accumulation in different cell compartments. The constructs were transiently expressed in tobacco by means of agroinfiltration. Stable transgenic tobacco plants were also generated to provide seed for stable storage of the material as a pre-pandemic strategy. Results For both transient and transgenic expression systems the highest accumulation of full-length H5 protein occurred in the apoplastic spaces, while the highest accumulation of H5tr was in the endoplasmic reticulum. The H5 proteins were produced at relatively high concentrations in both systems. Following partial purification, haemagglutination and haemagglutination inhibition tests indicated that the conformation of the plant-produced HA variants was correct and the proteins were functional. The immunisation of chickens and mice with the candidate vaccines elicited HA-specific antibody responses. Conclusions We managed, after synthesis of two versions of a single gene, to produce by transient and transgenic expression in plants, two variants of a highly pathogenic avian influenza virus HA protein which could have vaccine potential. This is a proof of principle of the potential of plant-produced influenza vaccines as a feasible pandemic response strategy for South Africa and other developing countries.

Comparing measures of fat-free mass in overweight older adults using three different bioelectrical impedance devices and three prediction equations

Objectives: To compare measures of fat-free mass (FFM) by three different bioelectrical impedance analysis (BIA) devices and to assess the agreement between three different equations validated in older adult and/or overweight populations. Design: Cross-sectional study. Setting: Orthopaedics ward of Brisbane public hospital, Australia. Participants: Twenty-two overweight, older Australians (72 yr ± 6.4, BMI 34 kg/m2 ± 5.5) with knee osteoarthritis. Measurements: Body composition was measured using three BIA devices: Tanita 300-GS (foot-to-foot), Impedimed DF50 (hand-to-foot) and Impedimed SFB7 (bioelectrical impedance spectroscopy (BIS)). Three equations for predicting FFM were selected based on their ability to be applied to an older adult and/ or overweight population. Impedance values were extracted from the hand-to-foot BIA device and included in the equations to estimate FFM. Results: The mean FFM measured by BIS (57.6 kg ± 9.1) differed significantly from those measured by foot-to-foot (54.6 kg ± 8.7) and hand-to-foot BIA (53.2 kg ± 10.5) (P < 0.001). The mean ± SD FFM predicted by three equations using raw data from hand-to-foot BIA were 54.7 kg ± 8.9, 54.7 kg ± 7.9 and 52.9 kg ± 11.05 respectively. These results did not differ from the FFM predicted by the hand-to-foot device (F = 2.66, P = 0.118). Conclusions: Our results suggest that foot-to-foot and hand-to-foot BIA may be used interchangeably in overweight older adults at the group level but due to the large limits of agreement may lead to unacceptable error in individuals. There was no difference between the three prediction equations however these results should be confirmed within a larger sample and against a reference standard.

The standard bearers : Governing teachers through professional standards

Teacher professional standards have become a key policy mechanism for the reform of teaching and education in recent years. While standards policies claim to improve the quality of teaching and learning in schools today, this paper argues that a disjunction exists between the stated intentions of such programmes and the intelligibility of the practices of government in which they are invested. To this effect, the paper conducts an analytics of government of the recently released National Professional Standards for Teachers (Australian Institute for Teaching and School Leadership, 2011) arguing that the explicit, calculated rationality of the programme exists within a wider field of effects. Such analysis has the critical consequence of calling into question the claims of the programmers themselves thus breaching the self-evidence on which the standards rest.

Australian new graduate experiences during their transition program in a rural/regional acute setting

The transition process from student to Registered Nurse has been recognised as an important yet challenging time for newly graduated nurses. Knowledge about this experience from the nurse’s perspective, particularly in a rural setting, is limited. This paper reports the findings of a qualitative study of the experiences of newly graduated nurses working in a rural acute care facility in New South Wales. The study examined, from the perspective of the new nurse, the orientation and support which can help to facilitate the transition from student to registered nurse. Four themes emerged which were being supported, being challenged, reflections on being a new graduate, and reflections on a rural new graduate program. These findings contribute to what is know about the transition of new graduates in a rural facility and have implications for program improvements, specifically within the rural acute care environment. The findings are also relevant to students considering rural employment on graduation and for the recruitment and retention of New Graduate Registered Nurses in rural areas.

A longitudinal study of mental health in refugees from Burma : the impact of therapeutic interventions

Objective: The present study seeks to examine the impact of therapeutic interventions for people from refugee backgrounds within a naturalistic setting. Method: Sixty-two refugees from Burma were assessed soon after arriving in Australia. All participants received standard interventions provided by a resettlement organisation which included therapeutic interventions, assessment, social assistance, and referrals where appropriate. At the completion of service provision a follow-up assessment was conducted. Results: Over the course of the intervention, participants experienced a significant decrease in symptoms of post-traumatic stress disorder, anxiety, depression and somatisation. Pre-intervention symptoms predicted symptoms post-intervention for post-traumatic stress, anxiety, and somatisation. Post-migration living difficulties, the number of traumas experienced, and the number of contacts with the service agency were unrelated to all mental health outcomes. Conclusions: In the first Australian study of its kind, reductions in mental health symptoms post-intervention were significantly linked to pre-intervention symptomatology and the number of therapy sessions predicted post-intervention symptoms of post-traumatic stress. Future studies need to include larger samples and control groups to verify findings.

End-of-life care in the intensive care setting : a descriptive exploratory qualitative study of nurses' beliefs and practices

Background: End-of-life care is a significant component of work in intensive care. Limited research has been undertaken on the provision of end-of-life care by nurses in the intensive care setting. The purpose of this study was to explore the end-of-life care beliefs and practices of intensive care nurses. Methods: A descriptive exploratory qualitative research approach was used to invite a convenience sample of five intensive care nurses from one hospital to participate in a semi-structured interview. Interview transcripts were analysed using an inductive coding approach. Findings: Three major categories emerged from analysis of the interviews: beliefs about end-of-life care, end-of-life care in the intensive care context and facilitating end-of-life care. The first two categories incorporated factors contributing to the end-of-life care experiences and practices of intensive care nurses. The third category captured the nurses’ end-of-life care practices. Conclusions: Despite the uncertainty and ambiguity surrounding end-of-life care in this practice context, the intensive care setting presents unique opportunities for nurses to facilitate positive end-of-life experiences and nurses valued their participation in the provision of end-of-life care. Care of the family was at the core of nurses’ end-of-life care work and nurses play a pivotal role in supporting the patient and their family to have positive and meaningful experiences at the end-of-life.Variation in personal beliefs and organisational support may influence nurses’ experiences and the care provided to patients and their families. Strategies to promote an organisational culture supportive of quality end-of-life care practices, and to mentor and support nurses in the provision of this care are needed.

Managing intravenous medications in the non-hospital setting: An ethnographic investigation

Little published information exists about the issues involved in conducting complex intravenous medication therapy in patients' homes. An ethnographic study of a local hospital-in-the-home program in the Australian Capital Territory explored this phenomenon to identify those factors that had an impact on the use of medicine in the home environment. This article focuses on one of the three themes identified in the study-Clinical Practice. Within this theme, topics related to the organization and management of intravenous medications, geography and diversity of patient caseload, and communication in the practice setting are discussed. These findings have important implications for policy development and establishment of a research agenda for hospital-in-the-home services.