Direct measurement as a tool for assessing the accuracy of inverse dynamics

The understanding of the loads generated within the prosthetic leg can aid engineers in the design of components and clinicians in the process of rehabilitation. Traditional methods to assess these loads have relied on inverse dynamics. This indirect method estimates the applied load using video recordings and force-plates located at a distance from the region of interest, such as the base of the residuum. The well-known limitations of this method are related to the accuracy of this recursive model and the experimental conditions required (Frossard et al., 2003). Recent developments in sensors (Frossard et al., 2003) and prosthetic fixation (Brånemark et al., 2000) permit the direct measurement of the loads applied on the residuum of transfemoral amputees. In principle, direct measurement should be an appropriate tool for assessing the accuracy of inverse dynamics. The purpose of this paper is to determine the validity of this assumption. The comparative variable used in this study is the velocity of the relative body center of mass (VCOM(t)). The relativity is used to align the static (w.r.t. position) force plate measurement with the dynamic load cell measurement.

Size-resolved particle distribution and gaseous concentrations by real-world road tunnel measurement

Measurements of aerosol particle number size distributions (15-700 nm), CO and NOx were performed in a bus tunnel, Australia. Daily mean particle size distributions of mixed diesel/CNG (Compressed Natural Gas) buses traffic flow were determined in 4 consecutive measurement days. EFs (Emission Factors) of Particle size distribution of diesel buses and CNG buses were obtained by MLR (Multiple Linear Regression) methods, particle distributions of diesel buses and CNG buses were observed as single accumulation mode and nuclei-mode separately. Particle size distributions of mixed traffic flow were decomposed by two log-normal fitting curves for each 30 minutes interval mean scans, all the mix fleet PSD emission can be well fitted by the summation of two log-normal distribution curves, and these were composed of nuclei mode curve and accumulation curve, which were affirmed as the CNG buses and diesel buses PN emission curves respectively. Finally, particle size distributions of diesel buses and CNG buses were quantified by statistical whisker-box charts. For log-normal particle size distribution of diesel buses, accumulation mode diameters were 74.5～87.5nm, geometric standard deviations were 1.89～1.98. As to log-normal particle size distribution of CNG buses, nuclei-mode diameters were 21～24 nm, geometric standard deviations were 1.27～1.31.

Effectiveness of in-office blood pressure measurement by eye care practitioners in early detection and management of hypertension

AIM To investigate the number of hypertensive patients, the optometrist is able to identify by routinely taking blood pressure (BP) measurements for patients in "at -risk" groups, and to sample patients' opinions regarding in -office BP measurement. Many of the optometrists in Saudi Arabia practice in optical stores. These stores are wide spread, easily accessible and seldom need appointments. The expanding role of the optometrist as a primary health care provider (PHCP) and the increasing global prevalence of hypertension, highlight the need for an integrated approach towards detecting and monitoring hypertension. METHODS Automated BP measurements were made twice (during the same session) at five selected optometry practices using a validated BP monitor (Omron M6) to assess the number of patients with high BP (HBP) - in at -risk groups -visiting the eye clinic routinely. Prior to data collection, practitioners underwent a two-day training workshop by a cardiologist on hypertension and how to obtain accurate BP readings. A protocol for BP measurement was distributed and retained in all participating clinics. The general attitude towards cardiovascular health of 480 patients aged 37.2 (依12.4)y and their opinion towards in-office BP measurement was assessed using a self -administered questionnaire. RESULTS A response rate of 83.6% was obtained for the survey. Ninety -three of the 443 patients (21.0% ) tested for BP in this study had HBP. Of these, (62 subjects) 67.7% were unaware of their HBP status. Thirty of the 105 subjects (28.6%) who had previously been diagnosed with HBP, still had HBP at the time of this study, and only 22 (73.3%) of these patients were on medication. Also, only 25% of the diagnosed hypertensive patients owned a BP monitor. CONCLUSION Taking BP measurements in optometry practices, we were able to identify one previously undiagnosed patient with HBP for every 8 adults tested. We also identified 30 of 105 previously diagnosed patients whose BP was poorly controlled, twenty-two of whom were on medication. The patients who participated in this study were positively disposed toward the routine measurement of BP by optometrists.

Investigating teachers' concerns and experiences in teaching children with special educational needs in Bhutan

This study investigated Bhutanese teachers' concerns and experiences in teaching children with Special Educational Needs in both inclusive and special schools. A mixed method design, combining quantitative and qualitative methods was used to answer the research questions. The aim of collecting quantitative data was to identify the key concerns. The aim of collecting qualitative data was to find out how teachers were experiencing including students with SEN in the classrooms. In doing so, three major issues were highlighted from this study: lack of classroom and human resources, lack of policy and lack of professional development for teachers.

Education in stroke prevention: Efficacy of an educational counselling intervention to increase knowledge in stroke survivors

BACKGROUND Motivational interviewing and stages of change are approaches to increasing knowledge and effecting behavioural change. This study examined the application of this approach on stroke knowledge acquisition and changing individual lifestyle risk factors in an outpatient clinic. METHODS RCT in which 200 participants were allocated to an education-counselling interview (ECI) or a control group. ECI group participants mapped their individual risk factors on a stage of change model and received an appointment to the next group lifestyle class. Participants completed a stroke knowledge questionnaire at baseline (T1), post-appointment, and three months (T3) post-appointment. Passive to active changes in lifestyle behaviour were self-reported at three months. RESULTS There was a statistically significant difference between groups from T1 toT3 in stroke knowledge (p < 0.001). While there was a significant shift from a passive to active stage of change for the overall study sample (p < 0.000), there was no significant difference between groups on the identified risk factors. CONCLUSIONS Although contact with patients in ambulatory clinical settings is limited due to time constraints, it is still possible to improve knowledge and initiate lifestyle changes utilizing motivational interviewing and a stage of change model. Stroke nurses may wish to consider these techniques in their practice setting.

Spine curvature analysis between participants with obesity and normal weight participants: A biplanar electromagnetic device measurement

To analyse and compare standing thoracolumbar curves in normal weight participants and participants with obesity, using an electromagnetic device, and to analyse the measurement reliability. Material and Methods. Cross-sectional study was carried out. 36 individuals were divided into two groups (normal-weight and participants with obesity) according to their waist circumference. The reference points (T1–T8–L1–L5 and both posterior superior iliac spines) were used to perform a description of thoracolumbar curvature in the sagittal and coronal planes. A transformation from the global coordinate system was performed and thoracolumbar curves were adjusted by fifth-order polynomial equations. The tangents of the first and fifth lumbar vertebrae and the first thoracic vertebra were determined from their derivatives. The reliability of the measurement was assessed according to the internal consistency of the measure and the thoracolumbar curvature angles were compared between groups. Results. Cronbach’s alpha values ranged between 0.824 (95% CI: 0.776–0.847) and 0.918 (95% CI: 0.903–0.949). In the coronal plane, no significant differences were found between groups; however, in sagittal plane, significant differences were observed for thoracic kyphosis. Conclusion. There were significant differences in thoracic kyphosis in the sagittal plane between two groups of young adults grouped according to their waist circumference.

Household carbon emission research: An analytical review of measurement, influencing factors and mitigation prospects

Greenhouse gas (GHG) emissions are simultaneously exhausting the world's supply of fossil fuels and threatening the global climate. In many developing countries, significant improvement in living standards in recent years due to the accelerating development of their economies has resulted in a disproportionate increase in household energy consumption. Therefore, a major reduction in household carbon emissions (HCEs) is essential if global carbon reduction targets are to be met. To do this, major Organisation for Economic Co-operation and Development (OECD) states have already implemented policies to alleviate the negative environmental effects of household behaviors and less carbon-intensive technologies are also proposed to promote energy efficiency and reduce carbon emissions. However, before any further remedial actions can be contemplated, though, it is important to fully understand the actual causes of such large HCEs and help researchers both gain deep insights into the development of the research domain and identify valuable research topics for future study. This paper reviews existing literature focusing on the domain of HCEs. This critical review provides a systematic understanding of current work in the field, describing the factors influencing HCEs under the themes of household income, household size, age, education level, location, gender and rebound effects. The main quantification methodologies of input–output models, life cycle assessment and emission coefficient methods are also presented, and the proposed measures to mitigate HCEs at the policy, technology and consumer levels. Finally, the limitations of work done to date and further research directions are identified for the benefit of future studies.

Educational interventions for preventing vascular catheter bloodstream infections in critical care: Evidence map, systematic review and economic evaluation

Background Bloodstream infections resulting from intravascular catheters (catheter-BSI) in critical care increase patients' length of stay, morbidity and mortality, and the management of these infections and their complications has been estimated to cost the NHS annually £19.1–36.2M. Catheter-BSI are thought to be largely preventable using educational interventions, but guidance as to which types of intervention might be most clinically effective is lacking. Objective To assess the effectiveness and cost-effectiveness of educational interventions for preventing catheter-BSI in critical care units in England. Data sources Sixteen electronic bibliographic databases – including MEDLINE, MEDLINE In-Process & Other Non-Indexed Citations, Cumulative Index to Nursing and Allied Health Literature (CINAHL), NHS Economic Evaluation Database (NHS EED), EMBASE and The Cochrane Library databases – were searched from database inception to February 2011, with searches updated in March 2012. Bibliographies of systematic reviews and related papers were screened and experts contacted to identify any additional references. Review methods References were screened independently by two reviewers using a priori selection criteria. A descriptive map was created to summarise the characteristics of relevant studies. Further selection criteria developed in consultation with the project Advisory Group were used to prioritise a subset of studies relevant to NHS practice and policy for systematic review. A decision-analytic economic model was developed to investigate the cost-effectiveness of educational interventions for preventing catheter-BSI. Results Seventy-four studies were included in the descriptive map, of which 24 were prioritised for systematic review. Studies have predominantly been conducted in the USA, using single-cohort before-and-after study designs. Diverse types of educational intervention appear effective at reducing the incidence density of catheter-BSI (risk ratios statistically significantly < 1.0), but single lectures were not effective. The economic model showed that implementing an educational intervention in critical care units in England would be cost-effective and potentially cost-saving, with incremental cost-effectiveness ratios under worst-case sensitivity analyses of < £5000/quality-adjusted life-year. Limitations Low-quality primary studies cannot definitively prove that the planned interventions were responsible for observed changes in catheter-BSI incidence. Poor reporting gave unclear estimates of risk of bias. Some model parameters were sourced from other locations owing to a lack of UK data. Conclusions Our results suggest that it would be cost-effective and may be cost-saving for the NHS to implement educational interventions in critical care units. However, more robust primary studies are needed to exclude the possible influence of secular trends on observed reductions in catheter-BSI.

A suitable method for journal bearing wear measurement

Purpose – Ideally, there is no wear in hydrodynamic lubrication regime. A small amount of wear occurs during start and stop of the machines and the amount of wear is so small that it is difficult to measure with accuracy. Various wear measuring techniques have been used where out-of-roundness was found to be the most reliable method of measuring small wear quantities in journal bearings. This technique was further developed to achieve higher accuracy in measuring small wear quantities. The method proved to be reliable as well as inexpensive. The paper aims to discuss these issues. Design/methodology/approach – In an experimental study, the effect of antiwear additives was studied on journal bearings lubricated with oil containing solid contaminants. The test duration was too long and the wear quantities achieved were too small. To minimise the test duration, short tests of about 90 min duration were conducted and wear was measured recording changes in variety of parameters related to weight, geometry and wear debris. The out-of-roundness was found to be the most effective method. This method was further refined by enlarging the out-of-roundness traces on a photocopier. The method was proved to be reliable and inexpensive. Findings – Study revealed that the most commonly used wear measurement techniques such as weight loss, roughness changes and change in particle count were not adequate for measuring small wear quantities in journal bearings. Out-of-roundness method with some refinements was found to be one of the most reliable methods for measuring small wear quantities in journal bearings working in hydrodynamic lubrication regime. By enlarging the out-of-roundness traces and determining the worn area of the bearing cross-section, weight loss in bearings was calculated, which was repeatable and reliable. Research limitations/implications – This research is a basic in nature where a rudimentary solution has been developed for measuring small wear quantities in rotary devices such as journal bearings. The method requires enlarging traces on a photocopier and determining the shape of the worn area on an out-of-roundness trace on a transparency, which is a simple but a crude method. This may require an automated procedure to determine the weight loss from the out-of-roundness traces directly. This method can be very useful in reducing test duration and measuring wear quantities with higher precision in situations where wear quantities are very small. Practical implications – This research provides a reliable method of measuring wear of circular geometry. The Talyrond equipment used for measuring the change in out-of-roundness due to wear of bearings indicates that this equipment has high potential to be used as a wear measuring device also. Measurement of weight loss from the traces is an enhanced capability of this equipment and this research may lead to the development of a modified version of Talyrond type of equipment for wear measurements in circular machine components. Originality/value – Wear measurement in hydrodynamic bearings requires long duration tests to achieve adequate wear quantities. Out-of-roundness is one of the geometrical parameters that changes with progression of wear in a circular shape components. Thus, out-of-roundness is found to be an effective wear measuring parameter that relates to change in geometry. Method of increasing the sensitivity and enlargement of out-of-roundness traces is original work through which area of worn cross-section can be determined and weight loss can be derived for materials of known density with higher precision.

The measurement of intraocular pressure over positive soft contact lenses by rebound tonometry [Medición de la presión intraocular sobre lentes de contacto blandas positivas, mediante tonometría de rebote]

Purpose To investigate if the accuracy of intraocular pressure (IOP) measurements using rebound tonometry over disposable hydrogel (etafilcon A) contact lenses (CL) is affected by the positive power of the CLs. Methods The experimental group comprised 26 subjects, (8 male, 18 female). IOP measurements were undertaken on the subjects’ right eyes in random order using a Rebound Tonometer (ICare). The CLs had powers of +2.00D and +6.00D. Measurements were taken over each contact lens and also before and after the CLs had been worn. Results The IOP measure obtained with both CLs was significantly lower compared to the value without CLs (t test; p<0.001) but no significant difference was found between the two powers of CLs. Conclusions Rebound tonometry over positive hydrogel CLs leads to a certain degree of IOP underestimation. This result didn’t change for the two positive lenses used in the experiment, despite their large difference in power and therefore in lens thickness. Optometrists should bear this in mind when measuring IOP with the rebound tonometer over plus power contact lenses.

PW376 A pilot study of a post-discharge nurse-led, educational intervention on cardiac self-efficacy and anxiety in post-PCI patients

Introduction Hospitalisation for percutaneous coronary intervention (PCI) is often short, with limited nurse-teaching time and poor information absorption. Currently, patients are discharged home only to wait up to 4-8 weeks to commence a secondary prevention program and visit their cardiologist. This wait is an anxious time for patients and confidence or self-efficacy (SE) to self-manage may be low. Objectives To determine the effects of a nurse-led, educational intervention on participant SE and anxiety in the early post-discharge period. Methods A pilot study was undertaken as a randomised controlled clinical trial. Thirty-three participants were recruited, with n=13 randomised to the intervention group. A face-to-face, nurse-led, educational intervention was undertaken within the first 5-7 days post-discharge. Intervention group participants received standard post-discharge education, physical assessment, with a strong focus on the emotional impact of cardiovascular events and PCI. Early reiteration of post-discharge education was offered, along with health professional support with the aim to increase patients’ SE and to effectively manage their post-discharge health and well being, as well as anxieties. Self-efficacy to return to normal activities was measured to gauge participants’ abilities to manage post-PCI after attending the intervention using the cardiac self-efficacy (CSE) scale. State and trait anxiety was also measured using the State-Trait Anxiety Inventory (STAI) to determine if an increase in SE would influence participant anxiety. Results There were some increases in mean CSE scores in the intervention group participants over time. Areas of increase included return to normal social activities and confidence to change diet. Although reductions were observed in mean state and trait anxiety scores in both groups, an overall larger reduction in intervention group participants was observed over time. Conclusion It is essential that patients are given the education, support, and skills to self-manage in the early post-discharge period so that they have greater SE and are less anxious. This study provides some initial evidence that nurse-led support and education during this period, particularly the first week following PCI, is beneficial and could be trialled using alternate modes of communication to support remote and rural PCI patients and extend to other cardiovascular patients.

Evaluation of an intervention for patients with alcohol-related injuries: results of a mixed methods study

Objective: To explore the effect of education and training on the delivery of alcohol screening and brief intervention and referral to high-risk patients in a hospital setting. Main outcome measures included; delivery of training; practice change in relation to staff performing alcohol screening, brief intervention and referrals. Methods: Observational study design using mixed methods set in a tertiary referral hospital. Pre-post assessment of medical records and semi-structured interviews with key informants. Results: Routine screening for substance misuse (9% pre / 71.4% post) and wellbeing concerns (6.6% pre / 15 % post) was more frequent following the introduction of resources and staff participation in educational workshops. There was no evidence of a concomitant increase in delivery of brief intervention or referrals to services. Implementation challenges, including time constraints and staff attitudes, and enablers such as collaboration and visible pathways, were identified. Conclusion: Rates of patient screening increased, however barriers to delivery of brief intervention and referrals remained. Implementation strategies targeting specific barriers and enablers to introducing interventions are both required to improve the application of secondary prevention for patients in acute settings. Implications: Educational training, formalised liaison between services, systematised early intervention protocols, and continuous quality improvement processes will progress service delivery in this area.

The Connor-Davidson Resilience Scale (CD-RISC): Dimensionality and age-related measurement invariance with Australian cricketers

Objective This study explored the dimensionality and measurement invariance of the 25-item Connor-Davidson Resilience Scale (CD-RISC; Connor & Davidson, 2003) across samples of adult (n = 321; aged 20–36) and adolescent (n = 199; aged 12–18) Australian cricketers. Design Cross-sectional, self-report survey Methods An online, multi-section questionnaire. Results Confirmatory factor and item level analyses supported the psychometric superiority of a revised 10-item, unidimensional model of resilience over the original 25-item, five-factor measurement model. Positive and moderate correlations with hardiness as well as negative and moderate correlations with burnout components were evidenced thereby providing support for the convergent validity of the unidimensional model. Measurement invariance analyses of the unidimensional model across the two age-group samples supported configural (i.e., same factor structure across groups), metric (i.e., same pattern of factor loadings across the groups), and partial scalar invariance (i.e., mostly the same intercepts across the groups). Conclusion Evidence for a psychometrically sound measure of resilient qualities of the individual provides an important foundation upon which researchers can identify the antecedents to and outcomes of resilience in sport contexts.

Direct measurement of inner prosthesis loading during activities of daily living: Proposal for classification of functional outcome

Background The purpose of this presentation is to outline the relevance of the categorization of the load regime data to assess the functional output and usage of the prosthesis of lower limb amputees. The objectives are • To highlight the need for categorisation of activities of daily living • To present a categorization of load regime applied on residuum, • To present some descriptors of the four types of activity that could be detected, • To provide an example the results for a case. Methods The load applied on the osseointegrated fixation of one transfemoral amputee was recorded using a portable kinetic system for 5 hours. The load applied on the residuum was divided in four types of activities corresponding to inactivity, stationary loading, localized locomotion and directional locomotion as detailed in previously publications. Results The periods of directional locomotion, localized locomotion, and stationary loading occurred 44%, 34%, and 22% of recording time and each accounted for 51%, 38%, and 12% of the duration of the periods of activity, respectively. The absolute maximum force during directional locomotion, localized locomotion, and stationary loading was 19%, 15%, and 8% of the body weight on the anteroposterior axis, 20%, 19%, and 12% on the mediolateral axis, and 121%, 106%, and 99% on the long axis. A total of 2,783 gait cycles were recorded. Discussion Approximately 10% more gait cycles and 50% more of the total impulse than conventional analyses were identified. The proposed categorization and apparatus have the potential to complement conventional instruments, particularly for difficult cases.

The pedagogic prosthetic: Augmented learning as content-in-motion in hybrid educational spheres

This article draws on the design and implementation of three mobile learning projects introduced by Flanagan in 2011, 2012 and 2014 engaging a total of 206 participants. The latest of these projects is highlighted in this article. Two other projects provide additional examples of innovative strategies to engage mobile and cloud systems describing how electronic and mobile technology can help facilitate teaching and learning, assessment for learning and assessment as learning, and support communities of practice. The second section explains the theoretical premise supporting the implementation of technology and promulgates a hermeneutic phenomenological approach. The third section discusses mobility, both in terms of the exploration of wearable technology in the prototypes developed as a result of the projects, and the affordances of mobility within pedagogy. Finally the quantitative and qualitative methods in place to evaluate m-learning are explained.