Robust outdoor visual localization using a three-dimensional-edge map

Visual localization systems that are practical for autonomous vehicles in outdoor industrial applications must perform reliably in a wide range of conditions. Changing outdoor conditions cause difficulty by drastically altering the information available in the camera images. To confront the problem, we have developed a visual localization system that uses a surveyed three-dimensional (3D)-edge map of permanent structures in the environment. The map has the invariant properties necessary to achieve long-term robust operation. Previous 3D-edge map localization systems usually maintain a single pose hypothesis, making it difficult to initialize without an accurate prior pose estimate and also making them susceptible to misalignment with unmapped edges detected in the camera image. A multihypothesis particle filter is employed here to perform the initialization procedure with significant uncertainty in the vehicle's initial pose. A novel observation function for the particle filter is developed and evaluated against two existing functions. The new function is shown to further improve the abilities of the particle filter to converge given a very coarse estimate of the vehicle's initial pose. An intelligent exposure control algorithm is also developed that improves the quality of the pertinent information in the image. Results gathered over an entire sunny day and also during rainy weather illustrate that the localization system can operate in a wide range of outdoor conditions. The conclusion is that an invariant map, a robust multihypothesis localization algorithm, and an intelligent exposure control algorithm all combine to enable reliable visual localization through challenging outdoor conditions.

Augmenting RatSLAM using FAB-MAP-based visual data association

This paper investigates the use of the FAB-MAP appearance-only SLAM algorithm as a method for performing visual data association for RatSLAM, a semi-metric full SLAM system. While both systems have shown the ability to map large (60-70km) outdoor locations of approximately the same scale, for either larger areas or across longer time periods both algorithms encounter difficulties with false positive matches. By combining these algorithms using a mapping between appearance and pose space, both false positives and false negatives generated by FAB-MAP are significantly reduced during outdoor mapping using a forward-facing camera. The hybrid FAB-MAP-RatSLAM system developed demonstrates the potential for successful SLAM over large periods of time.

A Review of the "Digital Turn" in the New Literacy Studies

Digital communication has transformed literacy practices and assumed great importance in the functioning of workplace, recreational, and community contexts. This article reviews a decade of empirical work of the New Literacy Studies, identifying the shift toward research of digital literacy applications. The article engages with the central theoretical, methodological, and pragmatic challenges in the tradition of New Literacy Studies, while highlighting the distinctive trends in the digital strand. It identifies common patterns across new literacy practices through cross-comparisons of ethnographic research in digital media environments. It examines ways in which this research is taking into account power and pedagogy in normative contexts of literacy learning using the new media. Recommendations are given to strengthen the links between New Literacy Studies research and literacy curriculum, assessment, and accountability in the 21st century.

Mediatisation and institutions of public memory : digital storytelling and the apology

Institutions of public memory are increasingly undertaking co-creative media initiatives in which community members create content with the support of institutional expertise and resources. This paper discusses one such initiative: the State Library of Queensland’s ‘Responses to the Apology’, which used a collaborative digital storytelling methodology to co-produce seven short videos capturing individual responses to Prime Minister Kevin Rudd’s 2008 ‘Apology to Australia’s Indigenous Peoples’. In examining this program, we are interested not only in the juxtaposition of ‘ordinary’ responses to an ‘official’ event, but also in how the production and display of these stories might also demonstrate a larger mediatisation of public memory.

Music, media and making : humanising digital media in music education

This paper examines three functions of music technology in the study of music. Firstly, as a tool, secondly, as an instrument and, lastly, as a medium for thinking. As our societies become increasingly embroiled in digital media for representation and communication, our philosophies of music education need to adapt to integrate these developments while maintaining the essence of music. The foundation of music technology in the 1990s is the digital representation of sound. It is this fundamental shift to a new medium with which to represent sound that carries with it the challenge to address digital technology and its multiple effects on music creation and presentation. In this paper I suggest that music institutions should take a broad and integrated approach to the place of music technology in their courses, based on the understanding of digital representation of sound and these three functions it can serve. Educators should reconsider digital technologies such as synthesizers and computers as music instruments and cognitive amplifiers, not simply as efficient tools.

Digital design communication : measuring learner technological prowess and self-efficacy in problem resolution

Currently the Bachelor of Design is the generic degree offered to the four disciplines of Architecture, Landscape Architecture, Industrial Design, and Interior Design within the School of Design at the Queensland University of Technology. Regardless of discipline, Digital Communication is a core unit taken by the 600 first year students entering the Bachelor of Design degree. Within the design disciplines the communication of the designer's intentions is achieved primarily through the use of graphic images, with written information being considered as supportive or secondary. As such, Digital Communication attempts to educate learners in the fundamentals of this graphic design communication, using a generic digital or software tool. Past iterations of the unit have not acknowledged the subtle difference in design communication of the different design disciplines involved, and has used a single generic software tool. Following a review of the unit in 2008, it was decided that a single generic software tool was no longer entirely sufficient. This decision was based on the recognition that there was an increasing emergence of discipline specific digital tools, and an expressed student desire and apparent aptitude to learn these discipline specific tools. As a result the unit was reconstructed in 2009 to offer both discipline specific and generic software instruction, if elected by the student. This paper, apart from offering the general context and pedagogy of the existing and restructured units, will more importantly offer research data that validates the changes made to the unit. Most significant of this new data is the results of surveys that authenticate actual student aptitude versus desire in learning discipline specific tools. This is done through an exposure of student self efficacy in problem resolution and technological prowess - generally and specifically within the unit. More traditional means of validation is also presented that includes the results of the generic university-wide Learning Experience Survey of the unit, as well as a comparison between the assessment results of the restructured unit versus the previous year.

Three-dimensional imaging for a very large excavator

In this paper we describe the development of a three-dimensional (3D) imaging system for a 3500 tonne mining machine (dragline).Draglines are large walking cranes used for removing the dirt that covers a coal seam. Our group has been developing a dragline swing automation system since 1994. The system so far has been `blind' to its external environment. The work presented in this paper attempts to give the dragline an ability to sense its surroundings. A 3D digital terrain map (DTM) is created from data obtained from a two-dimensional laser scanner while the dragline swings. Experimental data from an operational dragline are presented.

Digital rights management

Digital rights management allows information owners to control the use and dissemination of electronic documents via a machine-readable licence. Documents are distributed in a protected form such that they may only be used with trusted environments, and only in accordance with terms and conditions stated in the licence. Digital rights management has found uses in protecting copyrighted audio-visual productions, private personal information, and companies' trade secrets and intellectual property. This chapter describes a general model of digital rights management together with the technologies used to implement each component of a digital rights management system, and desribes how digital rights management can be applied to secure the distribution of electronic information in a variety of contexts.

Digital scenography for "Markus the Sadist" : UK National Tour

How does a digitally mediated environment work towards the ongoing support of the Hip Hop landscape present in the work of Jonzi D productions UK National Tour of "Markus the Sadist"

A prototype system for the digital lodgement of spatial data

This dissertation develops the model of a prototype system for the digital lodgement of spatial data sets with statutory bodies responsible for the registration and approval of land related actions under the Torrens Title system. Spatial data pertain to the location of geographical entities together with their spatial dimensions and are classified as point, line, area or surface. This dissertation deals with a sub-set of spatial data, land boundary data that result from the activities performed by surveying and mapping organisations for the development of land parcels. The prototype system has been developed, utilising an event-driven paradigm for the user-interface, to exploit the potential of digital spatial data being generated from the utilisation of electronic techniques. The system provides for the creation of a digital model of the cadastral network and dependent data sets for an area of interest from hard copy records. This initial model is calibrated on registered control and updated by field survey to produce an amended model. The field-calibrated model then is electronically validated to ensure it complies with standards of format and content. The prototype system was designed specifically to create a database of land boundary data for subsequent retrieval by land professionals for surveying, mapping and related activities. Data extracted from this database are utilised for subsequent field survey operations without the need to create an initial digital model of an area of interest. Statistical reporting of differences resulting when subsequent initial and calibrated models are compared, replaces the traditional checking operations of spatial data performed by a land registry office. Digital lodgement of survey data is fundamental to the creation of the database of accurate land boundary data. This creation of the database is fundamental also to the efficient integration of accurate spatial data about land being generated by modem technology such as global positioning systems, and remote sensing and imaging, with land boundary information and other information held in Government databases. The prototype system developed provides for the delivery of accurate, digital land boundary data for the land registration process to ensure the continued maintenance of the integrity of the cadastre. Such data should meet also the more general and encompassing requirements of, and prove to be of tangible, longer term benefit to the developing, electronic land information industry.