Bond performance of CFRP strengthened steel members subjected to axial compression

This paper focuses on the use of externally bonded Carbon Fiber Reinforced Polymer (CFRP) materials to strengthen steel plates subjected to compression. A fully slender steel section was selected in this test programme. CFRP strengthened steel plates and non strengthened plates were tested to fail under compressive load. The middle part of the strut was strengthened using CFRP sheet. The length of the strengthened zone was varied. Eight specimens were tested in this test programme. The test results showed a significant strength gain of 47% and delaying of lateral torsional buckling failure mode of strengthened members. This study confirms that there is great potential to increase the short term performance of CFRP strengthened steel structure under axial compression.

Impacts of climatic factors on evolution of molecular diversity and the natural distribution of wild stocks of the giant freshwater prawn (Macrobrachium rosenbergii)

Natural distributions of most freshwater taxa are restricted geographically, a pattern that reflects dispersal limitation. Macrobrachium rosenbergii is unusual because it occurs naturally in rivers from near Pakistan in the west, across India and Bangladesh to the Malay Peninsula, and across the Sunda Shelf and Indonesian archipelago to western Java. Individuals cannot tolerate full marine conditions, so dispersal between river drainage basins must occur at limited geographical scales when ecological or climatic factors are favorable. We examined molecular diversity in wild populations of M. rosenbergii across its complete natural range to document patterns of diversity and to relate them to factors that have driven evolution of diversity in this species. We found 3 clades in the mitochondrial deoxyribonucleic acid (mtDNA) data set that corresponded geographically with eastern, central, and western sets of haplotypes that last shared a common ancestor 1 × 106 y ago. The eastern clade was closest to the common ancestor of all 3 clades and to the common ancestor with its congener, Macrobrachium spinipes, distributed east of Huxley's Line. Macrobrachium rosenbergii could have evolved in the western Indonesian archipelago and spread westward during the early to mid-Pleistocene to India and Sri Lanka. Additional groups identified in the nuclear DNA data set in the central and western clades probably indicate secondary contact via dispersal between regions and modern introductions that have mixed nuclear and mtDNA genes. Pleistocene sea-level fluctuations can explain dispersal across the Indonesian archipelago and parts of mainland southeastern Asia via changing river drainage connections in shallow seas on wide continental shelves. At the western end of the modern distribution where continental shelves are smaller, intermittent freshwater plumes from large rivers probably permitted larval dispersal across inshore areas of lowered salinity.

State-of-the-art : track degradation at bridge transitions

Transition zones between bridge decks and rail tracks suffer early failure due to poor interaction between rail vehicles and sudden changes of stiffness. This has been an ongoing problem to rail industry and yet still no systematic studies appear to have been taken to maintain a gradually smoothening transmission of forces between the bridge and its approach. Differential settlement between the bridge deck and rail track in the transition zone is the fundamental issue, which negatively impacts the rail industry by causing passenger discomfort, early damage to infrastructure and vehicle components, speed reduction, and frequent maintenance cycles. Identification of mechanism of the track degradation and factors affecting is imperative to design any mitigation method for reducing track degradation rate at the bridge transition zone. Unfortunately this issue is still not well understood, after conducting a numbers of reviews to evaluate the key causes, and introducing a wide range of mitigation techniques. In this study, a comprehensive analysis of the available literature has been carried out to develop either a novel design framework or a mitigation technique for the bridge transition zone. This paper addresses three critical questions in relation to the track degradation at transition zone: (1) what are the causes of bridge transition track degradation?; (2) what are the available mitigation techniques in reducing the track degradation rate?; (3) what are the factors affecting on poor performance of the existing mitigation techniques?. It is found that the absence of soil-water response, dynamic loading response, and behaviour of geotechnical characteristics under long-term conditions in existing track transition design frameworks critically influence on the failures of existing mitigation techniques. This paper also evaluates some of the existing design frameworks to identify how each design framework addresses the track degradation at the bridge transition zone.

First full-scale trials of pebble matrix filtration

Protecting slow sand filters from high turbidity waters by pre-treatment using Pebble Matrix Filtration (PMF) has been studied in the laboratory at University College London followed by pilot field trials in Papua New Guinea and Serbia. Subsequently, the construction of two full-scale PMF units, one out of concrete (4.8m x4.8m x 3.0m high) and the other using pre-cast Ferro-cement panels (900mm x 1600mm x 20mm thick) with an effective diameter of 4.7m and 3m height, and the combined effective plan area of 40 m2 was completed to protect an existing Slow Sand Filter system at the National Water Supply Drainage Board (NWSDB) in Sri Lanka. Although the plant was completed in April 2008 due to some major repairs to address some leaks and other construction defects in both filters, monitoring was intermittent until November 2008. The results on the plant performance are presented here along with some of the construction problems encountered during the project.

Sustainability in post disaster road infrastructure recovery projects and asset management

Civil infrastructure and especially roads are being impacted with increasing frequency by flood, Tsunami, cyclone related natural and manmade disasters in the world. Responding to such events and in preparing for more regular and intense climate-change induced events in future, the road governing agencies are reviewing how postdisaster road infrastructure recovery projects are best planned and delivered. In particular, there is awareness that rebuilding such infrastructure require sustainable asset management strategies across economic, environmental and social dimensions. A comprehensive asset management framework for pre and post disaster situations can minimize negative impacts on our communities, economy and environment. This research paper is focused on post disaster management in road infrastructures and road infrastructure asset management strategies used by road authorities. Analyzing the implications of disruption to transport network and associated services is an important part of preparing local and regional responses to the impacts of disasters. This research paper will contribute to strategic infrastructure asset planning, management leading to safe, efficient and integrated transport system that supports sustainable economic, social and environmental outcomes. This paper also focuses on proper asset management, governance and engineering principles which should be followed and adopted in post disaster recovery projects to maximize sustainability in environmental, social and economic dimensions.

Handmade clay balls and recycled crush glass as alternative media in water filtration

For many years materials such as quarried sand, anthracite, and granular activated carbon have been the principal media-products traditionally used in water and wastewater filtration plants. Pebble Matrix Filtration (PMF) is a novel non-chemical, sustainable pre-treatment method of protecting Slow Sand Filters (SSF) from high turbidity during heavy monsoon periods. PMF uses sand and pebbles as the filter media and the sustainability of this new technology might depend on availability and supply of pebbles and sand, both finite resources. In many countries there are two principal methods of obtaining pebbles and sand, namely dredging from rivers and beaches, and due to the scarcity of these resources in some countries the cost of pebbles is often 4-5 times higher than that of sand. In search for an alternative medium to pebbles after some preliminary laboratory tests conducted in Colombo-Sri Lanka, Poznan-Poland and Cambridge-UK, a 100-year-old brick factory near Sudbury, Suffolk, has produced hand-made clay pebbles satisfying the PMF quality requirements. As an alternative to sand, crushed recycled glass from a UK supplier was used and the PMF system was operated together with hand-made clay balls in the laboratory for high turbidity removal effectively. The results of laboratory experiments with alternative media are presented in this paper. There are potential opportunities for recycled crushed glass and clay ball manufacturing processes in some countries where they can be used as filter media.

Design of light gauge steel roofing systems subject to high wind forces

Light gauge steel roofing systems made of thin profiled roof sheeting and battens are used commonly in residential, industrial and commercial buildings. Their critical design load combination is that due to wind uplift forces that occur during high wind events such as tropical cyclones and thunderstorms. However, premature local failures at their screw connections have been a concern for many decades since cyclone Tracy that devastated Darwin in 1974. Extensive research that followed cyclone Tracy on the pull-through and pull-out failures of roof sheeting to batten connections has significantly improved the safety of roof sheeting. However, this has made the batten to rafter/truss connection the weakest, and recent wind damage investigations have shown the failures of these connections and the resulting loss of entire roof structures. Therefore an experimental research program using both small scale and full scale air-box tests is currently under way to investigate the pull-through failures of thin-walled steel battens under high wind uplift forces. Tests have demonstrated that occurrence of pull-through failures in the bottom flanges of steel batttens and the need to develop simple test and design methods as a function of many critical parameters such as steel batten geometry, thickness and grade, screw fastener sizes and other fastening details. This paper presents the details of local failures that occur in light fauge roofing systems, a review of the current design and test methods for steel battens and associated short comings, and the test results obtained to date on pull-through failures of battens from small scale and full scale tests. Finally, it proposes the use of suitable small scale test methods that can be used by both researchers and manufacturers of such screw-fastened light gauge steel batten systems.

Transformation in educational practices through STEM

The need for strong science, technology and innovation linkages between Higher Education Institutions (HEIs) and industries is a pivotal point for middle-income countries in their endeavor to enhance human capital in socioeconomic development. Currently, the University-Industry partnerships are at an infant stage in Sri Lankan higher education context. Technological maturity and effective communication skills are contributing factors for an efficient graduate profile. Also, expanding internship programs in particular for STEM disciplines provide work experience to students that would strengthen the relevance of higher education programs. This study reports historical overviews and current trends in STEM education in Sri Lanka. Emphasis will be drawn to recent technological and higher education curricular reforms. Data from the last 10 years were extracted from the higher education sector and Ministry of Higher Education Policy portfolios. Associations and trend analysis of the sector growth were compared with STEM existence, merger and predicted augmentations. Results were depicted and summarised based on STEM streams and disciplines. It was observed that the trend of STEM augmentation in the Sri Lankan Higher Education context is growing at a slow but steady pace. Further analysis with other sectors in particular, Industry information, would be useful and a worthwhile exercise.

STEM education for sustainable development : a sociotechnical analysis

It is debated that for sustainable STEM education and knowledge investment, human centered learning design approach is critical and important. Sustainability in this context is enduring maintenance of technological trajectories for productive economical and social interactions by demonstrating life critical scenarios through life critical system development and life experiences. Technology influences way of life and the learning and teaching process. Social software application development is more than learning of how to program a software application and extracting information from the Internet. Hence, our research challenge is, how do we attract learners to STEM social software application development? Our realisation processes begin with comparing Science and Technology education in developed (e.g., Australia) and developing (e.g., Sri Lanka) countries with distinction on final year undergraduates’ industry ready training programmes. Principal components analysis was performed to separate patterns of important factors. To measure behavioural intention of perceived usefulness and attitudes of the training, the measurement model was analysed to test its validity and reliability using partial least square (PLS) analysis of structural equation modelling (SEM). Our observation is that the relationship is more complex than we argue for. Our initial conclusions were that life critical system development and life experience trajectories as determinant factors while technological influences were unavoidable. A further investigation should involve correlations between human centered learning design approach and economical development in the long run.

Model for internal porosity development of different shaped foods

Three particular geometrical shapes of foods were prepared from food materials. Cuboidal (aspect ratio = 1:1, 2:1, 3:1) , cylindrical (length: dameter = 1:1, 2:1, 3:1) and spheres were selected from potato, beans and peas respectively. Internal porosity was determined from solid density (theoretical)and particle density (experimental) during fluidised bed drying at different moisture contents. Solid density was calculated using formulae (conservation of mass and volume) already published in the literature by previous researchers. Determined porosity values were correlated with moisture ratio for different geometrical shapes.

Reducing building information fragmentation : a BIM-specifications approach

The world of Construction is changing, so too are the expectations of stakeholders regarding strategies for adapting existing resources (people, equipment and finances), processes and tools to the evolving needs of the industry. Building Information Modelling (BIM) is a data-rich, digital approach for representing building information required for design and construction. BIM tools play a crucial role and are instrumental to current approaches, by industry stakeholders, aimed at harnessing the power of a single information repository for improved project delivery and maintenance. Yet, building specifications - which document information on material quality, and workmanship requirements - remain distinctly separate from model information typically represented in BIM models. BIM adoption for building design, construction and maintenance is an industry-wide strategy aimed at addressing such concerns about information fragmentation. However, to effectively reduce inefficiencies due to fragmentation, BIM models require crucial building information contained in specifications. This paper profiles some specification tools which have been used in industry as a means of bridging the BIM-Specifications divide. We analyse the distinction between current attempts at integrating BIM and specifications and our approach which utilizes rich specification information embedded within objects in a product library as a method for improving the quality of information contained in BIM objects at various levels of model development.

A novel approach for numerical simulation of plant tissue shrinkage during drying

Drying is a key processing techniques used in food engineering which demands continual developments on advanced analysis techniques in order to optimize the product and the process. In this regard, plant based materials are a frequent subject of interest where microstructural studies can provide a clearer understanding on the fundamental physical mechanisms involved. In this context, considering numerous challenges of using conventional numerical grid-based modelling techniques, a meshfree particle based model was developed to simulate extreme deformations of plant microstructure during drying. The proposed technique is based on a particle based meshfree method: Smoothed Particle Hydrodynamics (SPH) and a Discrete Element Method (DEM). A tissue model was developed by aggrading individual cells modelled with SPH-DEM coupled approach by initializing the cells as hexagons and aggregating them to form a tissue. The model also involves a middle lamella resembling real tissues. Using the model, different dried tissue states were simulated with different moisture content, the turgor pressure, and cell wall contraction effects. Compared to the state of the art grid-based microscale plant tissue drying models, the proposed model is capable of simulating plant tissues at lower moisture contents which results in excessive shrinkage and cell wall wrinkling. Model predictions were compared with experimental findings and a fairly good agreement was observed both qualitatively and quantitatively.

Keynote address : aligning HR with a changing business landscape

"Firstly, I thank you sincerely for your kind invitation and warm welcome to Sri Lanka and to this national HR conference, I particularly acknowledge the initiative of Chairman of the Technical Committee, Dr Asoka Jinadasa in making it possible for me to be here, and to offer this contribution to your conference. I congratulate you on assembling such an impressive array of talent to aid your discussions. I hope I can add usefully to your conversations. In particular I congratulate you on developing such a good definition of HRM: “A strategic and integrated approach in acquisition, development and engagement of talent using relevant tools, with proper policies, products and processes in creating a conducive climate towards achieving organizational excellence and societal well-being” To me, that means that HR has to add value to the organisation, through an integrated set of tools, competencies, and policies, which are all consistent with the business model..."

A dual inverter based supercapacitor direct integration scheme for wind energy conversion systems

This paper presents a new direct integration scheme for supercapacitors that are used to mitigate short term power fluctuations in wind power systems. The proposed scheme uses the popular dual inverter topology for grid connection as well as interfacing a supercapacitor bank. The dual inverter system is formed by cascading two 2-level inverters named as the “main inverter” and the “auxiliary inverter”. The main inverter is powered by the rectified output of a wind turbine coupled permanent magnet synchronous generator. The auxiliary inverter is directly connected to a super capacitor bank. This approach eliminates the need for an interfacing dc-dc converter for the supercapacitor bank and thus improves the overall efficiency. A detailed analysis on the effects of non-integer dynamically changing voltage ratio is presented. The concept of integrated boost rectifier is used to carry out the Maximum Power Point Tracking (MPPT) of the wind turbine generator. Another novel feature of this paper is the power reference adjuster which effectively manages capacitor charging and discharging at extreme conditions. Simulation results are presented to verify the efficacy of the proposed system in suppressing short term wind power fluctuations.

Entomopathogens for control of Hypsipyla spp

Published information on the incidence of pathogens in the field and laboratory infections of Hypsipyla spp. with entomopathogens is reviewed. In addition, some preliminary results of field collections from Ghana and Costa Rica are presented. Fungal pathogens from the Deuteromycetes have been isolated from both H. robusta Moore and H. grandella Zeller. Mermithid nematodes, Hexamermis spp., have been frequently isolated from larvae in the field and incidence of infection with these pathogens can reach significant levels. Microsporidia have been found in cadavers of larvae collected in the field but none have been identified so far. A number of pathogens of other Lepidoptera have been shown to be infectious to H. grandella , including Bacillus thuringiensis , Deuteromycete fungi and a nucleopolyhedrovirus (NPV) from Autographa californica . Hypsipyla spp. are difficult targets for microbial control, since the larvae are cryptic, occur at low density and occur sporadically. In addition, there is a low damage threshold, the plant is susceptible for a number of years and the susceptible part of the plant will rapidly outgrow any surface application. Key features of the biology of entomopathogens with relevance to the control of low density and cryptic pests are discussed. In the light of this experience, we discuss strategies to improve the possibilities of microbial control of this pest and suggest areas for research.