A practical and theoretical definition of 'small field'

Introduction The consistency of measuring small field output factors is greatly increased by reporting the measured dosimetric field size of each factor, as opposed to simply stating the nominal field size [1] and therefore requires the measurement of cross-axis profiles in a water tank. However, this makes output factor measurements time consuming. This project establishes at which field size the accuracy of output factors are not affected by the use of potentially inaccurate nominal field sizes, which we believe establishes a practical working definition of a ‘small’ field. The physical components of the radiation beam that contribute to the rapid change in output factor at small field sizes are examined in detail. The physical interaction that dominates the cause of the rapid dose reduction is quantified, and leads to the establishment of a theoretical definition of a ‘small’ field. Methods Current recommendations suggest that radiation collimation systems and isocentre defining lasers should both be calibrated to permit a maximum positioning uncertainty of 1 mm [2]. The proposed practical definition for small field sizes is as follows: if the output factor changes by ±1.0 % given a change in either field size or detector position of up to ±1 mm then the field should be considered small. Monte Carlo modelling was used to simulate output factors of a 6 MV photon beam for square fields with side lengths from 4.0 to 20.0 mm in 1.0 mm increments. The dose was scored to a 0.5 mm wide and 2.0 mm deep cylindrical volume of water within a cubic water phantom, at a depth of 5 cm and SSD of 95 cm. The maximum difference due to a collimator error of ±1 mm was found by comparing the output factors of adjacent field sizes. The output factor simulations were repeated 1 mm off-axis to quantify the effect of detector misalignment. Further simulations separated the total output factor into collimator scatter factor and phantom scatter factor. The collimator scatter factor was further separated into primary source occlusion effects and ‘traditional’ effects (a combination of flattening filter and jaw scatter etc.). The phantom scatter was separated in photon scatter and electronic disequilibrium. Each of these factors was plotted as a function of field size in order to quantify how each affected the change in small field size. Results The use of our practical definition resulted in field sizes of 15 mm or less being characterised as ‘small’. The change in field size had a greater effect than that of detector misalignment. For field sizes of 12 mm or less, electronic disequilibrium was found to cause the largest change in dose to the central axis (d = 5 cm). Source occlusion also caused a large change in output factor for field sizes less than 8 mm. Discussion and conclusions The measurement of cross-axis profiles are only required for output factor measurements for field sizes of 15 mm or less (for a 6 MV beam on Varian iX linear accelerator). This is expected to be dependent on linear accelerator spot size and photon energy. While some electronic disequilibrium was shown to occur at field sizes as large as 30 mm (the ‘traditional’ definition of small field [3]), it has been shown that it does not cause a greater change than photon scatter until a field size of 12 mm, at which point it becomes by far the most dominant effect.

Using objective physical activity measures with youth : How many days of monitoring are needed?

Purpose The purpose of this study was to establish the minimal number of days of monitoring required for accelerometers to assess usual physical activity in children. Methods A total of 381 students (189 M, 192 F) wore a CSA 7164 uniaxial accelerometer for seven consecutive days. To examine age-related trends students were grouped as follows: Group I: grades 1-3 (N = 92); Group II: grades 4-6 (N = 98); Group III: grades 7-9 (N = 97); Group IV: grades 10-12 (N = 94). Average daily time spent in moderate-to-vigorous physical activity (MVPA) was calculated from minute-by-minute activity counts using the regression equation developed by Freedson et al. (1997). Results Compared with adolescents in grades 7 to 12, children in grades 1 to 6 exhibited less day-to-day variability in MVPA behavior. Spearman-Brown analysts indicated that between 4 and 5 d of monitoring would be necessary to a achieve a reliability of 0.80 in children, and between 8 and 9 d of monitoring would be necessary to achieve a reliability of 0.80 in adolescents. Within all grade levels, the 7-d monitoring protocol produced acceptable estimates of daily participation in MVPA (R = 0.76 (0.71-0.81) to 0.87 (0.84-0.90)). Compared with weekdays, children exhibited significantly higher levels of MVPA on weekends, whereas adolescents exhibited significantly lower levels of MVPA on weekends. Principal components analysis revealed two distinct time components for MVPA during the day for children (early morning, rest of the day), and three distinct time components for MVPA during the day for adolescents (morning, afternoon, early evening). Conclusions These results indicate that a 7-d monitoring protocol provides reliable estimates of usual physical activity behavior in children and adolescents and accounts for potentially important differences in weekend versus weekday activity behavior as well as differences in activity patterns within a given day.

Are mothers of young children really inactive?

Australian surveys have found that only 43% of women meet the current recommendation for regular moderate physical activity, and that women who are mothers of young children are even less likely to be adequately active for health benefit. These women spend a significant proportion of their day in occupational, household and care-giving activities, which may not be ‘captured’ in conventional physical activity surveys. The purpose of this study was to compare physical activity in young mothers and age-matched controls using three different measures of physical activity. 35 women (16 mothers of young children, M) and 19 age-matched comparison women (NM) completed a survey which asked about walking to and from places, and about moderate and vigorous activity in leisure time and at work (paid and unpaid). They also kept a detailed diary of all their activities for two week-days and two week-end days, and wore a pedometer (Yamax digiwalker) on these days. Each activity in the diary was assigned an energy expenditure (EE) score based on it's intensity (Compendium of Physical Activity) and time spent in that activity. There were no differences between M and NM for pedometer steps (M: 9270 sd 2947; NM: 9768 sd 3051) or for daily energy expenditure (EE) calculated from the diaries (M: 2029 sd 189; NM: 2015 sd 169 METS.mins) or survey (M: 2079 sd 448; NM: 1495 sd 325). There was a significant correlation between pedometer steps and daily METs.mins estimated from the diaries (r = 0.35, p = 0.04); however no relationship was observed between pedometer steps and EE from the survey (r = .09, p = .56). Further analysis of the individual survey items found pedometer steps to be related to EE from walking to and from places (r = .34) and leisure time (r = .31), but not work related activity (r = -.08). There were no significant relationships between EE computed from the diaries and any of the survey questions. The three activity measures indicate that the physical activity levels of the young mothers in our sample were comparable to age-matched non-mothers. The results of the correlation analyses highlight the difficulty of assessing low-intensity work-related physical activity via self-report. Supported by Australian Commonwealth Department of Health and Aged Care.

Impact of a change in tillage and crop residue management practice on soil chemical and microbiological properties in a cereal-producing red duplex soil in NSW, Australia

The effect of a change of tillage and crop residue management practice on the chemical and micro-biological properties of a cereal-producing red duplex soil was investigated by superimposing each of three management practices (CC: conventional cultivation, stubble burnt, crop conventionally sown; DD: direct-drilling, stubble retained, no cultivation, crop direct-drilled; SI: stubble incorporated with a single cultivation, crop conventionally sown), for a 3-year period on plots previously managed with each of the same three practices for 14 years. A change from DD to CC or SI practice resulted in a significant decline, in the top 0-5 cm of soil, in organic C, total N, electrical conductivity, NH4-N, NO3-N, soil moisture holding capacity, microbial biomass and CO2 respiration as well as a decline in the microbial quotient (the ratio of microbial biomass C to organic C; P <0.05). In contrast, a change from SI to DD or CC practice or a change from CC to DD or SI practice had only negligible impact on soil chemical properties (P >0.05). However, there was a significant increase in microbial biomass and the microbial quotient in the top 0-5 cm of soil following the change from CC to DD or SI practice and with the change from SI to DD practice (P <0.05). Analysis of ester-linked fatty acid methyl esters (EL-FAMEs) extracted from the 0- to 5-cm and 5- to 10-cm layers of the soils of the various treatments detected changes in the FAME profiles following a change in tillage practice. A change from DD practice to SI or CC practice was associated with a significant decline in the ratio of fungal to bacterial fatty acids in the 0- to 5-cm soil (P <0.05). The results show that a change in tillage practice, particularly the cultivation of a previously minimum-tilled (direct-drilled) soil, will result in significant changes in soil chemical and microbiological properties within a 3-year period. They also show that soil microbiological properties are sensitive indicators of a change in tillage practice.

Wheat breeding nurseries, target environments, and indirect selection for grain yield

Use of appropriate nursery environments will maximize gain from selection for yield of wheat (Triticum aestivum L.) in the target population of environments of a breeding program. The objective of this study was to investigate how well-irrigated (low-stress) nursery environments predict yield of lines in target environments that varied in degree of water limitation. Fifteen lines were sampled from the preliminary yield evaluation stage of the Queensland wheat breeding program and tested in 26 trials under on-farm conditions (Target Environments) across nine years (1985 to 1993) and also in 27 trials conducted at three research stations (Nursery Environments) in three years (1987 to 1989). The nursery environments were structured to impose different levels of water and nitrogen (N) limitation, whereas the target environments represented a random sample of on-farm conditions from the target population of environments. Indirect selection and pattern analysis methods were used to investigate selection for yield in the nursery environments and gain from selection in the target environments. Yield under low-stress nursery conditions was an effective predictor of yield under similar low-stress target environments (r = 0.89, P < 0.01). However, the value of the low-stress nursery as a predictor of yield in the water-limited target environments decreased with increasing water stress (moderate stress r = 0.53, P < 0.05, to r = 0.38, P > 0.05; severe stress r = -0.08, P > 0.05). Yield in the stress nurseries was a poor predictor of yield in the target environments. Until there is a clear understanding of the physiological-genetic basis of variation for adaptation of wheat to the water-limited environments in Queensland, yield improvement can best be achieved by selection for a combination of yield potential in an irrigated low-stress nursery and yield in on-farm trials that sample the range of water-limited environments of the target population of environments.

Bistability and hysteresis in inductively coupled plasmas

The transition between the two stable operation regimes (E and H discharge modes) in inductively coupled argon plasmas has been studied experimentally and theoretically. Analogy with other physical phenomena exhibiting hysteresis has been drawn. Analysis of power balance, electromagnetic field, plasma parameters, densities of the excited states, and optical emission spectra shows that the hysteresis may be due to nonlinearities associated with step-wise ionization through excited states of the argon atoms.

On cheating immune secret sharing

The paper addresses the cheating prevention in secret sharing. We consider secret sharing with binary shares. The secret also is binary. This model allows us to use results and constructions from the well developed theory of cryptographically strong boolean functions. In particular, we prove that for given secret sharing, the average cheating probability over all cheating vectors and all original vectors, i.e., 1/n 2n ∑c=1...n ∑α∈V n ρc,α , denoted by ρ, satisfies ρ ≥ ½, and the equality holds if and only if ρc,α satisfies ρc,α= ½ for every cheating vector δc and every original vector α. In this case the secret sharing is said to be cheating immune. We further establish a relationship between cheating-immune secret sharing and cryptographic criteria of boolean functions.This enables us to construct cheating-immune secret sharing.

A story about being engaged in research : buzzing bees, small business and Australian unfair dismissal laws

Protection for employees from unfair dismissal (UFD) has been around in Australia under various guises for 30 years or so (Chapman, 2006). Labour standards, and particularly ILO Convention 158 (Convention Concerning Termination of Employment at the Initiative of the Employer 1982), underpin the adoption of a particular form of federal statutory UFD regime which first appeared in the 1993 reforms to the Industrial Relations Act 1998 (Commonwealth). Its existence, however, has not been uncontroversial, and the meaning, operation, scope and remedies have attracted attention over time. In fact, the first reforms to the federal UFD regime were undertaken under the Keating Labor government three months after they were enacted (Chapman, ibid.). Further reforms were made by the incoming Howard Liberal-national coalition government through the Workplace Relations Act 1996 (Commonwealth) (WRA), and arguably these reforms continued down the ‘contraction’ path (ibid.).

Class notes : 10 principles of good BPM

The question concerning what makes for good BPM is often raised. A recent call from Paul Harmon on the BPTrends Discussion LinkedIN Group for key issues in BPM received 189 answers within two months, with additional answers still appearing. I have teamed up with a number of BPM researchers and practitioners to bring together our joint experience in a BPM workshop at the University in Liechtenstein in 2013, where we developed ten principles of good BPM, later published in Business Process Management Journal (vom Brocke et al., 2014). The paper, which has received considerable attention in academia, was ranked the journal’s most downloaded paper the month it was published. Slides on Slideshare that provide a brief summary of the paper have been accessed more than 3,000 times since they were first put online in March 2014. Given the importance of the topic–what makes for good BPM–and the positive response to the ten principles, I wrote this note with the co-authors of the original BPMJ paper to outline the ten principles and illustrate how to use them in practice. We invite all readers to engage in this discussion via any channel they find appropriate.

Species differences in acrylonitrile metabolism and toxicity between experimental animals and humans based on observations in human accidental poisonings

The high acute toxicity of acrylonitrile may be a result of its intrinsic biological reactivity or of its metabolite cyanide. Intravenous N-acetylcysteine has been recommended for treatment of accidental intoxications in acrylonitrile workers, but such recommendations vary internationally. Acrylonitrile is metabolized in humans and experimental animals via two competing pathways; the glutathione-dependent pathway is considered to represent an avenue of detoxication whilst the oxidative pathway leads to a genotoxic epoxide, cyanoethylene oxide, and to elimination of cyanide. Cases of acute acrylonitrile overexposure or intoxication have occurred within persons having industrial contact with acrylonitrile; the route of exposure was by inhalation and/or by skin contact. The combined observations lead to the conclusion of a much higher impact of the oxidative metabolism of acrylonitrile in humans than in rodents. This is confirmed by differences in the clinical picture of acute life-threatening intoxications in both species, as well as by differential efficacies of antidotes. A combination of N-acetylcysteine with sodium thiosulfate seems an appropriate measure for antidote therapy of acute acrylonitrile intoxications. Clinical observations also highlight the practical importance of human individual susceptibility differences. Furthermore, differential adduct monitoring, assessing protein adducts with different rates of decay, enables the development of more elaborated biological monitoring strategies for the surveillance of workers with potential acrylonitrile contact.

Transplantation of human amnion epithelial cells reduces hepatic fibrosis in immunocompetent CCl4-treated mice

Chronic liver injury and inflammation lead to hepatic fibrosis, cirrhosis, and liver failure. Embryonic and mesenchymal stem cells have been shown to reduce experimental liver fibrosis but have potential limitations, including the formation of dysplastic precursors, tumors, and profibrogenic cells. Other stem-like cells may reduce hepatic inflammation and fibrosis without tumor and profibrogenic cell formation. To test this hypothesis we transplanted human amnion epithelial cells (hAEC), isolated from term delivered placenta, into immunocompetent C57/BL6 mice at week 2 of a 4-week regimen of carbon tetrachloride (CCl4) exposure to induce liver fibrosis. Two weeks following hAEC infusion, intact cells expressing the human-specific markers inner mitochondrial membrane protein and human leukocyte antigen-G were found in mouse liver without evidence of host rejection of the transplanted cells. Human albumin, known to be produced by hAEC, was detected in sera of hAEC-treated mice. Human DNA was detected in mouse liver and also spleen, lungs, and heart of some animals. Following hAEC transplantation, CCl4-treated animals showed decreased serum ALT levels and reduced hepatocyte apoptosis, compared to controls. hAEC-treated mouse liver had lower TNF-α and IL-6 protein levels and higher IL-10 compared to animals given CCl4 alone. Compared to CCl4 controls, hAEC-treated mice showed fewer activated collagen-producing hepatic stellate cells and less fibrosis area and collagen content. Reduced hepatic TGF-β levels in conjunction with a twofold increase in the active form of the collagen-degrading enzyme matrix metalloproteinase-2 in hAEC-treated mice compared to CCl4 controls may account for the reduction in fibrosis. hAEC transplantation into immunocompetent mice leads to cell engraftment, reduced hepatocyte apoptosis, and decreased hepatic inflammation and fibrosis.

Exploring the usefulness of structural–functional approaches to analyse governance of planning systems

Existing planning theories tend to be limited in their analytical scope and often fail to account for the impact of many interactions between the multitudes of stakeholders involved in strategic planning processes. Although many theorists rejected structural–functional approaches from the 1970s, this article argues that many of structural–functional concepts remain relevant and useful to planning practitioners. In fact, structural–functional approaches are highly useful and practical when used as a foundation for systemic analysis of real-world, multi-layered, complex planning systems to support evidence-based governance reform. Such approaches provide a logical and systematic approach to the analysis of the wider governance of strategic planning systems that is grounded in systems theory and complementary to existing theories of complexity and planning. While we do not propose its use as a grand theory of planning, this article discusses how structural–functional concepts and approaches might be applied to underpin a practical analysis of the complex decision-making arrangements that drive planning practice, and to provide the evidence needed to target reform of poorly performing arrangements.

Learning about inclusion from developing countries : using the index for inclusion

There is a need for a more critical perspective and reporting about the value of taking a model of inclusion developed in western countries and based upon the human rights ethos applying it in developing countries. This chapter will report firstly on how the Index for Inclusion (hereinafter referred to as the Index) was used in Australia as a tool for review and development; and secondly how the process of using the Index is adjusted for use in the Pacific Islands and other developing nations in collaborative and culturally sensitive ways to support and evaluate progress towards inclusive education. Examples are provided from both contexts to demonstrate the impact of the Index as an effective tool to support a more inclusive response to diversity in schools.