Investigation of 'off-line‘ relaxation phenomena in oil filled transformers

Power transformers are one of the most important and costly equipment in power generation, transmission and distribution systems. Current average age of transformers in Australia is around 25 years and there is a strong economical tendency to use them up to 50 years or more. As the transformers operate, they get degraded due to different loading and environmental operating stressed conditions. In today‘s competitive energy market with the penetration of distributed energy sources, the transformers are stressed more with minimum required maintenance. The modern asset management program tries to increase the usage life time of power transformers with prognostic techniques using condition indicators. In the case of oil filled transformers, condition monitoring methods based on dissolved gas analysis, polarization studies, partial discharge studies, frequency response analysis studies to check the mechanical integrity, IR heat monitoring and other vibration monitoring techniques are in use. In the current research program, studies have been initiated to identify the degradation of insulating materials by the electrical relaxation technique known as dielectrometry. Aging leads to main degradation products like moisture and other oxidized products due to fluctuating thermal and electrical loading. By applying repetitive low frequency high voltage sine wave perturbations in the range of 100 to 200 V peak across available terminals of power transformer, the conductive and polarization parameters of insulation aging are identified. An in-house novel digital instrument is developed to record the low leakage response of repetitive polarization currents in three terminals configuration. The technique is tested with known three transformers of rating 5 kVA or more. The effects of stressing polarization voltage level, polarizing wave shapes and various terminal configurations provide characteristic aging relaxation information. By using different analyses, sensitive parameters of aging are identified and it is presented in this thesis.

Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

Development of pollutant build-up parameters for MIKE URBAN for Southeast Queensland, Australia

Accurate estimation of input parameters is essential to ensure the accuracy and reliability of hydrologic and water quality modelling. Calibration is an approach to obtain accurate input parameters for comparing observed and simulated results. However, the calibration approach is limited as it is only applicable to catchments where monitoring data is available. Therefore, methodology to estimate appropriate model input parameters is critical, particularly for catchments where monitoring data is not available. In the research study discussed in the paper, pollutant build-up parameters derived from catchment field investigations and model calibration using MIKE URBAN are compared for three catchments in Southeast Queensland, Australia. Additionally, the sensitivity of MIKE URBAN input parameters was analysed. It was found that Reduction Factor is the most sensitive parameter for peak flow and total runoff volume estimation whilst Build-up rate is the most sensitive parameter for TSS load estimation. Consequently, these input parameters should be determined accurately in hydrologic and water quality simulations using MIKE URBAN. Furthermore, an empirical equation for Southeast Queensland, Australia for the conversion of build-up parameters derived from catchment field investigations as MIKE URBAN input build-up parameters was derived. This will provide guidance for allowing for regional variations in the estimation of input parameters for catchment modelling using MIKE URBAN where monitoring data is not available.

Modelling of inflatable rescue boats (IRBs) in surf conditions to reduce injuries

The Inflatable Rescue Boat (IRB) is arguably the most effective rescue tool used by the Australian surf lifesavers. The exceptional features of high mobility and rapid response have enabled it to become an icon on Australia's popular beaches. However, the IRB's extensive use within an environment that is as rugged as it is spectacular, has led it to become a danger to those who risk their lives to save others. Epidemiological research revealed lower limb injuries to be predominant, particularly the right leg. The common types of injuries were fractures and dislocations, as well as muscle or ligament strains and tears. The concern expressed by Surf Life Saving Queensland (SLSQ) and Surf Life Saving Australia (SLSA) led to a biomechanical investigation into this unique and relatively unresearched field. The aim of the research was to identify the causes of injury and propose processes that may reduce the instances and severity of injury to surf lifesavers during IRB operation. Following a review of related research, a design analysis of the craft was undertaken as an introduction to the craft, its design and uses. The mechanical characteristics of the vessel were then evaluated and the accelerations applied to the crew in the IRB were established through field tests. The data were then combined and modelled in the 3-D mathematical modelling and simulation package, MADYMO. A tool was created to compare various scenarios of boat design and methods of operation to determine possible mechanisms to reduce injuries. The results of this study showed that under simulated wave loading the boats flex around a pivot point determined by the position of the hinge in the floorboard. It was also found that the accelerations experienced by the crew exhibited similar characteristics to road vehicle accidents. Staged simulations indicated the attributes of an optimum foam in terms of thickness and density. Likewise, modelling of the boat and crew produced simulations that predicted realistic crew response to tested variables. Unfortunately, the observed lack of adherence to the SLSA footstrap Standard has impeded successful epidemiological and modelling outcomes. If uniformity of boat setup can be assured then epidemiological studies will be able to highlight the influence of implementing changes to the boat design. In conclusion, the research provided a tool to successfully link the epidemiology and injury diagnosis to the mechanical engineering design through the use of biomechanics. This was a novel application of the mathematical modelling software MADYMO. Other craft can also be investigated in this manner to provide solutions to the problem identified and therefore reduce risk of injury for the operators.

The domestic kitchen : the weak link in the food chain : is convenience leading to apathy?

To investigate the meaning and understanding of domestic food preparation within the lived experience of the household's main food preparer this ethnographic study used a combination of qualitative and quantitative methodologies. Data were collected from three sources: the literature; an in-store survey of251 food shoppers chosen at random while shopping during both peak and off peak shopping periods at metropolitan supermarkets; and semi-structured interviews with the principal food shopper and food preparer of 15 different Brisbane households. Male and female respondents representing a cross section of socio-economic groupings, ranged in age from 19-79 years and were all from English speaking backgrounds. Changes in paid labour force participation, income and education have increased the value of the respondents' time, instigating massive changes in the way they shop, cook and eat. Much of their food preparation has moved from the domestic kitchen into the kitchens of other food establishments. For both sexes, the dominant motivating force behind these changes is a combination of the their self perceived lack of culinary skill; lack of enjoyment of cooking and lack of motivation to cook. The females in paid employment emphasise all factors, particularly the latter two, significantly more than the non-employed females. All factors are of increasing importance for individuals aged less than 35 years and conversely, of significantly diminished importance to older respondents. Overall, it is the respondents aged less than 25 years who indicate the lowest cooking frequency and/or least cooking ability. Inherent in this latter group is an indifference to the art/practice of preparing food. Increasingly, all respondents want to do less cooking and/or get the cooking over with as quickly as possible. Convenience is a powerful lure by which to spend less time in the kitchen. As well, there is an apparent willingness to pay a premium for convenience. Because children today are increasingly unlikely to be taught to cook, addressing the food skills deficit and encouraging individuals to cook for themselves are significant issues confronting health educators. These issues are suggested as appropriate subjects of future research.

Evaluating the effect of a patient education brochure on patients’ expectations and satisfaction with emergency department service

Introduction: The purpose of this study was to assess the capacity of a written intervention, in this case a patient information brochure, to improve patient satisfaction during an Emergency Department (ED) visit. For the purpose of measuring the effect of the intervention the ED journey was conceptualised as a series of distinct areas of service comprising waiting time, service by the triage nurse, care from doctors and nurses and information giving Background of study: Research into patient satisfaction has become a widespread activity endorsed by both governments and hospital administrations. The literature on ED patient satisfaction has consistently indicated three primary areas of patient dissatisfaction: waiting time, nursing care and communication. Recent developments in the literature on patient satisfaction studies however have highlighted the relationship between patients. expectations of a service encounter and their consequent assessment of the experience as dissatisfying or satisfying. Disconfirmation theory posits that the degree to which expectations are confirmed will affect subsequent levels of satisfaction. The conceptual framework utilised in this study is Coye.s (2004) model of disconfirmation. Coye while reiterating satisfaction is a consequence of the degree expectations are either confirmed or disconfirmed also posits that expectations can be modified by interventions. Coye.s work conceptualises these interventions as intra encounter experiences (cues) which function to adjust expectations. Coye suggests some cues are unintended and may have a negative impact which also reinforces the value of planned cues intended to meet or exceed consumer expectations. Consequently the brochure can be characterized as a potentially positive cue, encouraging the patient to understand processes and to orient them in what can be a confronting environment. Only a limited number of studies have examined the effect of written interventions within an ED. No studies could be located which have tested the effect of ED interventions using a conceptual framework which relates the effect of the degree to which expectations are confirmed or disconfirmed in terms of satisfaction with services. Method: Two studies were conducted. Study One used qualitative methods to explore patients. expectations of the ED from the perspective of both patients and health care professionals. Study One was used in part to direct the development of the intervention (brochure) in Study Two. The brochure was an intervention designed to modify patients. expectations thus increasing their satisfaction with the provision of ED service. As there was no existing tools to measure ED patients. expectations and satisfaction a new tool was also developed based on the findings and the literature of Study One. Study Two used a non-randomised, quasi-experimental approach using a non-equivalent post-test only comparison group design used to investigate the effect of the patient education brochure (Stommel and Wills, 2004). The brochure was disseminated to one of two study groups (the intervention group). The effect of the brochure was assessed by comparing the data obtained from both the intervention and control group. These two groups consisted of 150 participants each. It was expected that any differences in the relevant domains selected for examination would indicate the effect of the brochure both on expectation and potentially satisfaction. Results: Study One revealed several areas of common ground between patients and nurses in terms of relevant content for the written intervention, including the need for information on the triage system and waiting times. Areas of difference were also found with patients emphasizing communication issues, whereas focus group members expressed concern that patients were often unable to assimilate verbal information. The findings suggested the potential utility of written material to reinforce verbal communication particularly in terms of the triage process and other ED protocols. This material was synthesized within the final version of the written intervention. Overall the results of Study Two indicated no significant differences between the two groups. The intervention group did indicate a significant number of participants who viewed the brochure of having changed their expectations. The effect of the brochure may have been obscured by a lack of parity between the two groups as the control group presented with statistically significantly higher levels of acuity and experienced significantly shorter waiting times. In terms of disconfirmation theory this would suggest expectations that had been met or exceeded. The results confirmed the correlation of expectations with satisfaction. Several domains also indicated age as a significant predictor with older patients tending to score higher satisfaction results. Other significant predictors of satisfaction established were waiting time and care from nurses, reinforcing the combination of efficient service and positive interpersonal experiences as being valued by patients. Conclusions: Information presented in written form appears to benefit a significant number of ED users in terms of orientation and explaining systems and procedures. The degree to which these effects may interact with other dimensions of satisfaction however is likely to be limited. Waiting time and interpersonal behaviours from staff also provide influential cues in determining satisfaction. Written material is likely to be one element in a series of coordinated strategies to improve patient satisfaction during periods of peak demand.

Global trends in prescribing contact lenses for extended wear

Extended wear has long been the ‘holy grail’ of contact lenses by virtue of the increased convenience and freedom of lifestyle which they accord; however, this modality enjoyed only limited market success during the last quarter of the 20th century. The introduction of silicone hydrogel materials into the market at the beginning of this century heralded the promise of successful extended wear due to the superior oxygen performance of this lens type. To assess patterns of contact lens fitting, including extended wear, over the past decade, up to 1000 survey forms were sent to contact lens fitters in Australia, Canada, Japan, the Netherlands, Norway, the UK and the USA each year between 2000 and 2009. Practitioners were asked to record data relating to the first 10 contact lens fits or refits performed after receiving the survey form. Analysis of returned forms revealed that, averaged over this period, 9% of all soft lenses prescribed were for extended wear, with national figures ranging from 2% in Japan to 17% in Norway. The trend over the past decade has been for an increase from about 5% of all soft lens fits in 2000 to a peak of between 9 and 12% between 2002 and 2007, followed by a decline to around 7% in 2009. A person receiving extended wear lenses is likely to be an older female who is being refitted with silicone hydrogel lenses for full-time wear. Although extended wear has yet again failed to fulfil the promise of being the dominant contact lens wearing modality, it is still a viable option for many people.

Advanced Gen-1, 2 and 3 biofuels research in Australia - Fuelling advanced biofuels training for international scientists

Flinders University and Queensland University of Technology, biofuels research interests cover a broad range of activities. Both institutions are seeking to overcome the twin evils of "peak oil" (Hubbert 1949 & 1956) and "global warming" (IPPC 2007, Stern 2006, Alison 2010), through development of Generation 1, 2 and 3 (Gen-1, 2 & 3) biofuels (Clarke 2008, Clarke 2010). This includes development of parallel Chemical Biorefinery, value-added, co-product chemical technologies, which can underpin the commercial viability of the biofuel industry. Whilst there is a focused effort to develop Gen-2 & 3 biofuels, thus avoiding the socially unacceptable use of food based Gen-1 biofuels, it must also be recognized that as yet, no country in the world has produced sustainable Gen-2 & 3 biofuel on a commercial basis. For example, in 2008 the United States used 38 billion litres (3.5% of total fuel use) of Gen-1 biofuel; in 2009/2010 this will be 47.5 billion litres (4.5% of fuel use) and in 2018 this has been estimated to rise to 96 billion litres (9% of total US fuel use). Brazil in 2008 produced 24.5 billion litres of ethanol, representing 37.3% of the world’s ethanol use for fuel and Europe, in 2008, produced 11.7 billion litres of biofuel (primarily as biodiesel). Compare this to Australia’s miserly biofuel production in 2008/2009 of 180 million litres of ethanol and 75 million litres of biodiesel, which is 0.4% of our fuel consumption! (Clarke, Graiver and Habibie 2010) To assist in the development of better biofuels technologies in the Asian developing regions the Australian Government recently awarded the Materials & BioEnergy Group from Flinders University, in partnership with the Queensland University of Technology, an Australian Leadership Award (ALA) Biofuel Fellowship program to train scientists from Indonesia and India about all facets of advanced biofuel technology.

Colonization and osteogenic differentiation of different stem cell sources on electrospun nanofiber meshes

Numerous challenges remain in the successful clinical translation of cell-based therapies for musculoskeletal tissue repair, including the identification of an appropriate cell source and a viable cell delivery system. The aim of this study was to investigate the attachment, colonization, and osteogenic differentiation of two stem cell types, human mesenchymal stem cells (hMSCs) and human amniotic fluid stem (hAFS) cells, on electrospun nanofiber meshes. We demonstrate that nanofiber meshes are able to support these cell functions robustly, with both cell types demonstrating strong osteogenic potential. Differences in the kinetics of osteogenic differentiation were observed between hMSCs and hAFS cells, with the hAFS cells displaying a delayed alkaline phosphatase peak, but elevated mineral deposition, compared to hMSCs. We also compared the cell behavior on nanofiber meshes to that on tissue culture plastic, and observed that there is delayed initial attachment and proliferation on meshes, but enhanced mineralization at a later time point. Finally, cell-seeded nanofiber meshes were found to be effective in colonizing three-dimensional scaffolds in an in vitro system. This study provides support for the use of the nanofiber mesh as a model surface for cell culture in vitro, and a cell delivery vehicle for the repair of bone defects in vivo.

Vector control of a high power induction machine

The design and implementation of a high-power (2 MW peak) vector control drive is described. The inverter switching frequency is low, resulting in high-harmonic-content current waveforms. A block diagram of the physical system is given, and each component is described in some detail. The problem of commanded slip noise sensitivity, inherent in high-power vector control drives, is discussed, and a solution is proposed. Results are given which demonstrate the successful functioning of the system

Dynamic coast control of train movement with genetic algorithm

The railway service is now the major transportation means in most of the countries around the world. With the increasing population and expanding commercial and industrial activities, a high quality of railway service is the most desirable. Train service usually varies with the population activities throughout a day and train coordination and service regulation are then expected to meet the daily passengers' demand. Dwell time control at stations and fixed coasting point in an inter-station run are the current practices to regulate train service in most metro railway systems. However, a flexible and efficient train control and operation is not always possible. To minimize energy consumption of train operation and make certain compromises on the train schedule, coast control is an economical approach to balance run-time and energy consumption in railway operation if time is not an important issue, particularly at off-peak hours. The capability to identify the starting point for coasting according to the current traffic conditions provides the necessary flexibility for train operation. This paper presents an application of genetic algorithms (GA) to search for the appropriate coasting point(s) and investigates the possible improvement on fitness of genes. Single and multiple coasting point control with simple GA are developed to attain the solutions and their corresponding train movement is examined. Further, a hierarchical genetic algorithm (HGA) is introduced here to identify the number of coasting points required according to the traffic conditions, and Minimum-Allele-Reserve-Keeper (MARK) is adopted as a genetic operator to achieve fitter solutions.

Aboriginal public health and education : has it made a difference in practice?

Over the years, public health in relation to Australian Aboriginal people has involved many individuals and groups including health professionals, governments, politicians, special interest groups and corporate organisations. Since colonisation commenced until the1980s, public health relating to Aboriginal and Torres Strait Islander people was not necessarily in the best interests of Aboriginal and Torres Strait Islander people, but rather in the interests of the non-Aboriginal population. The attention that was paid focussed more generally around the subject of reproduction and issues of prostitution, exploitation, abuse and venereal diseases (Kidd, 1997). Since the late 1980s there has been a shift in the broader public health agenda (see Baum, 1998) along with public health in relation to Aboriginal and Torres Strait Islander people (NHMRC, 2003). This has been coupled with increasing calls to develop appropriate tertiary curriculum and to educate, train, and employ more Aboriginal and Torres Strait Islander and non-Aboriginal people in public health (Anderson et al., 2004; Genat, 2007; PHERP, 2008a, 2008b). Aboriginal and Torres Strait Islander people have been engaged in public health in ways in which they are in a position to influence the public health agenda (Anderson 2004; 2008; Anderson et al., 2004; NATSIHC, 2003). There have been numerous projects, programs and strategies that have sought to develop the Aboriginal and Torres Strait Islander Public Health workforce (AHMAC, 2002; Oldenburg et al., 2005; SCATSIH, 2002). In recent times the Aboriginal community controlled health sector has joined forces with other peak bodies and governments to find solutions and strategies to improve the health outcomes of Aboriginal and Torres Strait Islander peoples (NACCHO & Oxfam, 2007). This case study chapter will not address these broader activities. Instead it will explore the activities and roles of staff within the Public Health and Research Unit (PHRU) at the Victorian Aboriginal Community Controlled Health Organisation (VACCHO). It will focus on their experiences with education institutions, their work in public health and their thoughts on gaps and where improvements can be made in public health, research and education. What will be demonstrated is the diversity of education qualifications and experience. What will also be reflected is how people work within public health on a daily basis to enact change for equity in health and contribute to the improvement of future health outcomes of the Victorian Aboriginal community.

Restarting trains under moving block signalling : an expert system approach

A high peak power demand at substations will result under Moving Block Signalling (MBS) when a dense queue of trains begins to start from a complete stop at the same time in an electrified railway system. This may cause the power supply interruption and in turn affect the train service substantially. In a recent study, measures of Starting Time Delay (STD) and Acceleration Rate Limit (ARL) are the possible approaches to reduce the peak power demand on the supply system under MBS. Nevertheless, there is no well-defined relationship between the two measures and peak power demand reduction (PDR). In order to attain a lower peak demand at substations on different traffic conditions and system requirements, an expert system is one of the possible approaches to procure the appropriate use of peak demand reduction measures. The main objective of this paper is to study the effect of the train re-starting strategies on the power demand at substations and the time delay suffered by the trains with the aid of computer simulation. An expert system is a useful tool to select various adoptions of STD and ARL under different operational conditions and system requirements.

Exposure to ultrafine particles and PM2.5 in four Sydney transport modes

Concentrations of ultrafine (<0.1µm) particles (UFPs) and PM2.5 (<2.5µm) were measured whilst commuting along a similar route by train, bus, ferry and automobile in Sydney, Australia. One trip on each transport mode was undertaken during both morning and evening peak hours throughout a working week, for a total of 40 trips. Analyses comprised one-way ANOVA to compare overall (i.e. all trips combined) geometric mean concentrations of both particle fractions measured across transport modes, and assessment of both the correlation between wind speed and individual trip means of UFPs and PM2.5, and the correlation between the two particle fractions. Overall geometric mean concentrations of UFPs and PM2.5 ranged from 2.8 (train) to 8.4 (bus) × 104 particles cm-3 and 22.6 (automobile) to 29.6 (bus) µg m-3, respectively, and a statistically significant difference (p <0.001) between modes was found for both particle fractions. Individual trip geometric mean concentrations were between 9.7 × 103 (train) and 2.2 × 105 (bus) particles cm-3 and 9.5 (train) to 78.7 (train) µg m-3. Estimated commuter exposures were variable, and the highest return trip mean PM2.5 exposure occurred in the ferry mode, whilst the highest UFP exposure occurred during bus trips. The correlation between fractions was generally poor, and in keeping with the duality of particle mass and number emissions in vehicle-dominated urban areas. Wind speed was negatively correlated with, and a generally poor determinant of, UFP and PM2.5 concentrations, suggesting a more significant role for other factors in determining commuter exposure.

Community engagement and groundwater investigation in a rural/peri urban basaltic aquifier system, Tamborine Mountain, South East Queensland

The Tamborine Mt area is a popular residential and tourist area in the Gold Coast hinterland, SE Qld. The 15km2 area occurs on elevated remnant Tertiary Basalts of the Beechmont Group, which comprise a number of mappable flow units originally derived from the Tweed volcanic centre to the south. The older Albert Basalt (Tertiary), which underlies the Beechmont Basalt at the southern end of the investigation area, is thought to be derived from the Focal Peak volcanic centre to the south west. The Basalts contain a locally significant ‘un-declared’ groundwater resource, which is utilised by the Tamborine Mt community for: • domestic purposes to supplement rainwater tank supplies, • commercial scale horticulture and • commercial export off-Mountain for bottled water. There is no reticulated water supply, and all waste water is treated on-site through domestic scale WTPs. Rainforest and other riparian ecosystems that attract residents and tourist dollars to the area, are also reliant on the groundwater that discharges to springs and surface streams on and around the plateau. Issues regarding a lack of compiled groundwater information, groundwater contamination, and groundwater sustainability are being investigated by QUT, utilising funding provided by the Federal Government’s ‘Caring for our Country’ programme through SEQ Catchments Ltd. The objectives of the two year project, which started in April 2009, are to: • Characterise the nature and condition of groundwater / surface water systems in the Tamborine Mountain area in terms of the issues being raised; • Engage and build capacity within the community to source local knowledge, encourage participation, raise awareness and improve understanding of the impacts of land and water use; • Develop a stand-alone 3D Visualisation model for dissemination into the community and use as a communication tool.