STRATÉGÉ – Study of Transparent Recognition, Accreditation Tools and Experience in a Global Environment

Engineering graduates of today, face a working environment that assumes global mobility in the labour market. This challenge means, amongst universities worldwide, a demand to increase the globalisation of educational programs, context, and increase and support the mobility of students through mechanisms such as student exchange and double masters degrees. Engineering student mobility from Australia is low with only a few Engineering Faculties encouraging students to go internationally. This comparative study, using universities in Australia and Europe, of feedback from students who have been on exchange or proposing to go on exchange, employers and faculty addresses the motivators and barriers to student mobility and exchange from the perspectives of the university, faculty, students and employers. Recommendations will be presented on how student mobility and exchange can be improved, and mechanisms such as double Masters Degrees, dual accreditation and Erasmus Mundus 2009 – 2013 can be utilised to improve student mobility.

The S.T.A.B. Trial - Standardised Testing of Artificial Blood. A comparative study of various products that may be used as artificial blood for high fidelity simulation training in the critical care setting

Aim: In the current climate of medical education, there is an ever-increasing demand for and emphasis on simulation as both a teaching and training tool. The objective of our study was to compare the realism and practicality of a number of artificial blood products that could be used for high-fidelity simulation. Method: A literature and internet search was performed and 15 artificial blood products were identified from a variety of sources. One product was excluded due to its potential toxicity risks. Five observers, blinded to the products, performed two assessments on each product using an evaluation tool with 14 predefined criteria including color, consistency, clotting, and staining potential to manikin skin and clothing. Each criterion was rated using a five-point Likert scale. The products were left for 24 hours, both refrigerated and at room temperature, and then reassessed. Statistical analysis was performed to identify the most suitable products, and both inter- and intra-rater variability were examined. Results: Three products scored consistently well with all five assessors, with one product in particular scoring well in almost every criterion. This highest-rated product had a mean rating of 3.6 of 5.0 (95% posterior Interval 3.4-3.7). Inter-rater variability was minor with average ratings varying from 3.0 to 3.4 between the highest and lowest scorer. Intrarater variability was negligible with good agreement between first and second rating as per weighted kappa scores (K = 0.67). Conclusion: The most realistic and practical form of artificial blood identified was a commercial product called KD151 Flowing Blood Syrup. It was found to be not only realistic in appearance but practical in terms of storage and stain removal.

A review of LCADesign

Objective The review addresses two distinct sets of issues: 1. specific functionality, interface, and calculation problems that presumably can be fixed or improved; and 2. the more fundamental question of whether the system is close to being ready for ‘commercial prime time’ in the North American market. Findings Many of our comments relate to the first set of issues, especially sections B and C. Sections D and E deal with the second set. Overall, we feel that LCADesign represents a very impressive step forward in the ongoing quest to link CAD with LCA tools and, more importantly, to link the world of architectural practice and that of environmental research. From that perspective, it deserves continued financial support as a research project. However, if the decision is whether or not to continue the development program from a purely commercial perspective, we are less bullish. In terms of the North American market, there are no regulatory or other drivers to press design teams to use a tool of this nature. There is certainly interest in this area, but the tools must be very easy to use with little or no training. Understanding the results is as important in this regard as knowing how to apply the tool. Our comments are fairly negative when it comes to that aspect. Our opinion might change to some degree when the ‘fixes’ are made and the functionality improved. However, as discussed in more detail in the following sections, we feel that the multi-step process — CAD to IFC to LCADesign — could pose a serious problem in terms of market acceptance. The CAD to IFC part is impossible for us to judge with the information provided, and we can’t even begin to answer the question about the ease of using the software to import designs, but it appears cumbersome from what we do know. There does appear to be a developing North American market for 3D CAD, with a recent survey indicating that about 50% of the firms use some form of 3D modeling for about 75% of their projects. However, this does not mean that full 3D CAD is always being used. Our information suggests that AutoDesk accounts for about 75 to 80% of the 3D CAD market, and they are very cautious about any links that do not serve a latent demand. Finally, other system that link CAD to energy simulation are using XML data transfer protocols rather than IFC files, and it is our understanding that the market served by AutoDesk tends in that direction right now. This is a subject that is outside our area of expertise, so please take these comments as suggestions for more intensive market research rather than as definitive findings.

Passive control of a bi-ventricular assist device : an experimental and numerical investigation

For the last two decades heart disease has been the highest single cause of death for the human population. With an alarming number of patients requiring heart transplant, and donations not able to satisfy the demand, treatment looks to mechanical alternatives. Rotary Ventricular Assist Devices, VADs, are miniature pumps which can be implanted alongside the heart to assist its pumping function. These constant flow devices are smaller, more efficient and promise a longer operational life than more traditional pulsatile VADs. The development of rotary VADs has focused on single pumps assisting the left ventricle only to supply blood for the body. In many patients however, failure of both ventricles demands that an additional pulsatile device be used to support the failing right ventricle. This condition renders them hospital bound while they wait for an unlikely heart donation. Reported attempts to use two rotary pumps to support both ventricles concurrently have warned of inherent haemodynamic instability. Poor balancing of the pumps’ flow rates quickly leads to vascular congestion increasing the risk of oedema and ventricular ‘suckdown’ occluding the inlet to the pump. This thesis introduces a novel Bi-Ventricular Assist Device (BiVAD) configuration where the pump outputs are passively balanced by vascular pressure. The BiVAD consists of two rotary pumps straddling the mechanical passive controller. Fluctuations in vascular pressure induce small deflections within both pumps adjusting their outputs allowing them to maintain arterial pressure. To optimise the passive controller’s interaction with the circulation, the controller’s dynamic response is optimised with a spring, mass, damper arrangement. This two part study presents a comprehensive assessment of the prototype’s ‘viability’ as a support device. Its ‘viability’ was considered based on its sensitivity to pathogenic haemodynamics and the ability of the passive response to maintain healthy circulation. The first part of the study is an experimental investigation where a prototype device was designed and built, and then tested in a pulsatile mock circulation loop. The BiVAD was subjected to a range of haemodynamic imbalances as well as a dynamic analysis to assess the functionality of the mechanical damper. The second part introduces the development of a numerical program to simulate human circulation supported by the passively controlled BiVAD. Both investigations showed that the prototype was able to mimic the native baroreceptor response. Simulating hypertension, poor flow balancing and subsequent ventricular failure during BiVAD support allowed the passive controller’s response to be assessed. Triggered by the resulting pressure imbalance, the controller responded by passively adjusting the VAD outputs in order to maintain healthy arterial pressures. This baroreceptor-like response demonstrated the inherent stability of the auto regulating BiVAD prototype. Simulating pulmonary hypertension in the more observable numerical model, however, revealed a serious issue with the passive response. The subsequent decrease in venous return into the left heart went unnoticed by the passive controller. Meanwhile the coupled nature of the passive response not only decreased RVAD output to reduce pulmonary arterial pressure, but it also increased LVAD output. Consequently, the LVAD increased fluid evacuation from the left ventricle, LV, and so actually accelerated the onset of LV collapse. It was concluded that despite the inherently stable baroreceptor-like response of the passive controller, its lack of sensitivity to venous return made it unviable in its present configuration. The study revealed a number of other important findings. Perhaps the most significant was that the reduced pulse experienced during constant flow support unbalanced the ratio of effective resistances of both vascular circuits. Even during steady rotary support therefore, the resulting ventricle volume imbalance increased the likelihood of suckdown. Additionally, mechanical damping of the passive controller’s response successfully filtered out pressure fluctuations from residual ventricular function. Finally, the importance of recognising inertial contributions to blood flow in the atria and ventricles in a numerical simulation were highlighted. This thesis documents the first attempt to create a fully auto regulated rotary cardiac assist device. Initial results encourage development of an inlet configuration sensitive to low flow such as collapsible inlet cannulae. Combining this with the existing baroreceptor-like response of the passive controller will render a highly stable passively controlled BiVAD configuration. The prototype controller’s passive interaction with the vasculature is a significant step towards a highly stable new generation of artificial heart.

The role of decision-maker preferences in tenancy selection of CBD office accommodation – preliminary literature review

The literature and anecdotal evidence suggests that that there is more to tenancy selection (firm location) than the profit maximisation drive that traditional neo-classical economic location theory suggests. In the first instance these models assume property markets are rational and perfectly competitive; the CBD office market is clearly neither rational nor perfectly competitive. This fact alone relegates such models to the margins of usefulness for an industry that seeks to satisfy tenant demand in order to optimise returns on capital invested. Acknowledgment of property market imperfections are universally accepted to the extent that all contemporary texts discuss the lack of a coherent centralised market place and incomplete and poorly disseminated information processes as fundamental inadequacies which characterise the property market inefficiencies. Less well researched are the facets of the market which allow the observer to determine market activity to be significantly irrational. One such facet is that of ‘decision maker preferences’. The decision to locate a business operation at one location as opposed to another seems ostensibly a routine choice based on short, medium and long term business objectives. These objectives are derived from a process of strategic planning by one or more individuals whose goal is held to be to optimise outcomes which benefit the business (and presumably those employed within it). However the decision making processes appear bounded by how firms function, the institutional context in which they operate, as well as by opportunistic behaviour by individual decision makers who allow personal preferences to infiltrate and ‘corrupt’ the process. In this way, history, culture, geography, as well as institutions all become significant to the extent that these influence and shape individual behaviour which in turn determine the morphology of individual preferences, as well as providing a conduit for them to take effect. This paper exams historical and current literature on the impact of individual behaviour in the decision making process within organisations as a precursor to an investigation of the tenancy decision making process within the CBD office market. Literature on the topic falls within a number of research disciplines, philosophy, psychology and economics to name a few.

Selected elements of housing affordability impacting otherwise potentially sustainable communities

It is widely held that strong relationships exist between housing, economic status, and well being. Therefore, recent events emerging from the United States, culminating in widespread housing stock surpluses in that country and others, threaten to destabilise many aspects related to individuals and community. However, despite global impact, the position of housing demand and supply is not consistent. The Australian position provides a strong contrast whereby continued strong housing demand generally remains a critical issue affecting the socio-economic landscape. Underpinned by strong levels of immigration, and further buoyed by sustained historically low interest rates, increasing income levels, and increased government assistance for first home buyers, this strong housing demand ensures elements related to housing affordability continue to gain prominence. A significant, but less visible factor impacting housing affordability – particularly new housing development – relates to holding costs. These costs are in many ways “hidden” and cannot always be easily identified. Although it is only one contributor, the nature and extent of its impact requires elucidation. In its simplest form, it commences with a calculation of the interest or opportunity cost of land holding. However, there is significantly more complexity for major new developments - particularly greenfield development. Analysis suggests that even small shifts in primary factors impacting holding costs can appreciably affect housing affordability. Those factors of greatest significance not only include interest rates and the rate of inflation, but even less apparent factors such as the regulatory assessment period. These are not just theoretical concepts but real, measurable price drivers. Ultimately, the real impact is felt by the one market segment whom can typically least afford it – new home, first home buyers. They can be easily pushed out of affordability. This paper suggests the stability and sustainability of growing, new communities require this problem to be acknowledged and accurately identified if the well being of such communities is to be achieved.

A numerical method to quantify the axial shortening of vertical elements in concrete buildings

Differential axial shortening, distortion and deformation in high rise buildings is a serious concern. They are caused by three time dependent modes of volume change; “shrinkage”, “creep” and “elastic shortening” that takes place in every concrete element during and after construction. Vertical concrete components in a high rise building are sized and designed based on their strength demand to carry gravity and lateral loads. Therefore, columns and walls are sized, shaped and reinforced differently with varying concrete grades and volume to surface area ratios. These structural components may be subjected to the detrimental effects of differential axial shortening that escalates with increasing the height of buildings. This can have an adverse impact on other structural and non-structural elements. Limited procedures are available to quantify axial shortening, and the results obtained from them differ because each procedure is based on various assumptions and limited to few parameters. All these prompt to a need to develop an accurate numerical procedure to quantify the axial shortening of concrete buildings taking into account the important time varying functions of (i) construction sequence (ii) Young’s Modulus and (iii) creep and shrinkage models associated with reinforced concrete. General assumptions are refined to minimize variability of creep and shrinkage parameters to improve accuracy of the results. Finite element techniques are used in the procedure that employs time history analysis along with compression only elements to simulate staged construction behaviour. This paper presents such a procedure and illustrates it through an example. Keywords: Differential Axial Shortening, Concrete Buildings, Creep and Shrinkage, Construction Sequence, Finite Element Method.

The development of a clinical learning environment scale

Within nursing, there is a strong demand for high-quality, cost-effective clinical education experiences that facilitate student learning in the clinical setting The clinical learning environment (CLE) is the interactive network of forces within the clinical setting that influence the students'clinical learning outcomes The identification of factors that characterize CLE could lead to strategies that foster the factors most predictive of desirable student learning outcomes and ameliorate those which may have a negative impact on student outcomes The CLE scale is a 23-item instrument with five subscales staff–student relationships, nurse manager commitment, patient relationships, interpersonal relationships, and student satisfaction These factors have strong substantive face validity and construct validity, as determined by confirmatory factor analysis Reliability coefficients range from high (0 85) to marginal (0 63) The CLE scale provides the educator with a valid and reliable instrument to evaluate affectively relevant factors in the CLE, direct resources to areas where improvement may be required, and nurture those areas functioning well It will assist in the application of resources in a cost-effective, efficient, productive manner, and will ensure that the clinical learning experience offers the nursing student the best possible learning outcomes

Growing demand for emergency health services in Queensland, Australia

Introduction: The demand for emergency health services (EHS), both in the prehospital (ambulance) and hospital (emergency departments) settings, is growing rapidly in Australia. Broader health system changes have reduced available health infrastructure, particularly hospital beds, resulting in reduced access to and congestion of the EHS as demonstrated by longer waiting times and ambulance “ramping”. Ambulance ramping occurring when patients have a prolonged wait on the emergency vehicle due to the unavailability of hospital beds. This presentation will outline the trends in EHS demand in Queensland compared with the rest of Australia and factors that appear to be contributing to the growth in demand. Methods: Secondary analysis was conducted using data from publicly available sources. Data from the Queensland Ambulance Service and Queensland Health Emergency Department Information System (EDIS) also were analyzed. Results: The demand for ambulance services and emergency departments has been increasing at 8% and 4% per year over the last decade, respectively; while accessible hospital beds have reduced by almost 10% contributing to the emergency department congestion and possibly contributing to the prehospital demand. While the increase in the proportion of the elderly population seems to explain a great deal of the demand for EHS, other factors also influence this growth including patient characteristics, institutional and societal factors, economic, EHS arrangements, and clinical factors. Conclusions: Overcrowding of facilities that provide EHS are causing considerable community concern. This overcrowding is caused by the growing demand and reduced access. The causes of this growing demand are complex, and require further detailed analysis in order to quantify and qualify these causes in order to provide a resilient foundation of evidence for future policy direction.

A study of entrepreneurship : Taiwanese digital content companies in China

China’s accession to the World Trade Organisation (WTO) has greatly enhanced global interest in investment in the Chinese media market, where demand for digital content is growing rapidly. The East Asian region is positioned as a growth area in many forms of digital content and digital service industries. China is attempting to catch up and take its place as a production centre to offset challenges from neighbouring countries. Meanwhile, Taiwan is seeking to use China both as an export market and as a production site for its digital content. This research investigates entry strategies of Taiwanese digital content firms into the Chinese market. By examining the strategies of a sample of Taiwan-based companies, this study also explores the evolution of their market strategies. However, the focus is on how distinctive business practices such as guanxi are important to Taiwanese business and to relations with Mainland China. This research examines how entrepreneurs manage the characteristics of digital content products and in turn how digital content entrepreneurs adapt to changing market circumstances. This project selected five Taiwan-based digital content companies that have business operations in China: Wang Film, Artkey, CnYES, Somode and iPartment. The study involved a field trip, undertaken between November 2006 and March 2007 to Shanghai and Taiwan to conduct interviews and to gather documentation and archival reports. Six senior managers and nine experts were interviewed. Data were analysed according to Miller’s firm-level entrepreneurship theory, foreign direct investment theory, Life Cycle Model and guanxi philosophy. Most studies of SMEs have focused on free market (capitalist) environments. In contrast, this thesis examines how Taiwanese digital content firms’ strategies apply in the Chinese market. I identified three main types of business strategy: cost-reduction, innovation and quality-enhancement; and four categories of functional strategies: product, marketing, resource acquisition and organizational restructuring. In this study, I introduce the concept of ‘entrepreneurial guanxi’, special relationships that imply mutual obligation, assurance and understanding to secure and exchange favors in entrepreneurial activities. While guanxi is a feature of many studies of business in Pan-Chinese society, it plays an important mediating role in digital content industries. In this thesis, I integrate the ‘Life Cycle Model’ with the dynamic concept of strategy. I outline the significant differences in the evolution of strategy between two types of digital content companies: off-line firms (Wang Film and Artkey) and web-based firms (CnYES, Somode and iPartment). Off-line digital content firms tended to adopt ‘resource acquisition strategies’ in their initial stages and ‘marketing strategies’ in second and subsequent stages. In contrast, web-based digital content companies mainly adopted product and marketing strategies in the early stages, and would adopt innovative approaches towards product and marketing strategies in the whole process of their business development. Some web-based digital content companies also adopted organizational restructuring strategies in the final stage. Finally, I propose the ‘Taxonomy Matrix of Entrepreneurial Strategies’ to emphasise the two dimensions of this matrix: innovation, and the firm’s resource acquisition for entrepreneurial strategy. This matrix is divided into four cells: Effective, Bounded, Conservative, and Impoverished.

Comparative assessment of characteristics influencing the industrial property markets in Sydney and Hong Kong

Industrial property is commonly located in a designated ‘industrial’ precinct. An industrial property has a specific design and a number of services to support industrial activities including manufacture, distribution and transportation. Although it has a unique characteristic, certain industrial factor might operate differently in different countries. The aim of this paper is to provide a comparison between the Sydney and Hong Kong industrial property characteristics and to highlight their similarities and differences. This exploratory research used secondary data to provide background information of government policy and market conditions. Two case studies were use to illustrate similarities, trends, differences and to explore town planning, specific property characteristics including location, design and layout. Then, analyse whether these factors influence the performance and value of an industrial asset. The location of industrial properties varies between each country and depends heavily on infrastructure. It was noted that the town planning restrictions not only vary between markets and cities but also between property lots. The market conditions of both industrial markets were investigated and the supply and demand and rental levels in both cities were distinctly opposite.

Can Risk Management boost the supply of Affordable Housing Development and Management?

A shortage of affordable housing is a major problem in Australia today. This is mainly due to the limited supply of affordable housing that is provided by the non-government housing sector. Some private housing developers see the provision of affordable housing for lower income people as a high risk investment which offers a lower return than broader market-based housing. The scarcity of suitable land, a limited government ‘subsidy’, and increasing housing costs have not provided sufficient development incentives to encourage their investment despite the existing high demand for affordable housing. This study analyses the risk management process conducted by some private and not-for-profit housing providers in South East Queensland, and draws conclusions about the relationship between risk assessments/responses and past experiences. In-depth interviews of selected non-government housing providers have been conducted to facilitate an understanding of their approach to risk assessment/response in developing and in managing affordable housing projects. These developers use an informal risk management process as part of their normal business process in accordance with industry standards. A simple qualitative matrix has been used to analyse probability and impacts using a qualitative scale - low, medium and high. For housing providers who have considered investing in affordable housing but have not yet implemented any such projects, affordable housing development is seen as an opportunity that needs to be approached with caution. The risks associated with such projects and the levels of acceptance of these are not consistently identified by current housing providers. Many interviewees agree that the recognition of financial risk and the fear of community rejection of such housing projects have restrained them from committing to such investment projects. This study suggests that implementing improvements to the risk mitigation and management framework may assist in promoting the supply of affordable housing by non-government providers.

Exploring the impact of context-specific job stressors on employee work outcomes

A path model was developed to examine the impact of context-specific job stressors on the work outcomes of 132 customer service employees. Respondents who reported a moderate and high level of context-specific stressors report a higher level of job demand and work family conflict. Respondents who reported a higher level of job control tend to receive more work-related support and are more satisfied with their job. Surprisingly, respondents who experienced a higher level of work family conflict tend to receive less work-related support. We found that respondents who obtained more work-related support tend to report a higher level of job satisfaction. There was also a positive relationship between positive job satisfaction and a lower level of intention to quit.

Disclosing donation decisions : the role of organ donor prototypes in an extended theory of planned behaviour

This study explored the role of donor prototype evaluations (perceptions of the typical organ donor) in organ donation communication decisions using an extended theory of planned behaviour (TPB) model. The model incorporated attitude, subjective norm, perceived behavioural control, moral norm, self-identity, and donor prototype evaluations to predict intentions to record consent on an organ donor register and discuss the organ donation decision with significant others. Participants completed surveys assessing the extended TPB constructs related to registering (n = 359) and discussing (n = 282). Results supported a role for donor prototype evaluations in predicting discussing intentions only. Both extended TPB structural equation models were a good fit to the data, accounting for 74 and 76% of the variance in registering and discussing intentions, respectively. Participants’ self-reported discussing behaviour (but not registering behaviour given low numbers of behavioural performers) was assessed 4 weeks later, with discussing intention as the only significant predictor of behaviour (Nagelkerke R2 = 0.11). These findings highlight the impact of people's perceptions of a typical donor on their decisions to discuss their organ donation preference, assisting our understanding of the factors influencing individuals' communication processes in efforts to bridge the gap between organ supply and demand.

EMG biofeedback in the treatment of tinnitus : an experimental evaluation

26 tinnitus patients received either electromyogram (EMG) biofeedback with counterdemand instructions, EMG biofeedback with neutral demand instructions, or no treatment. Assessment was conducted on self-report measures of the distress associated with tinnitus, the loudness, annoyance and awareness of tinnitus, sleep-onset difficulties, depression, and anxiety. Audiological assessment of tinnitus was also conducted and EMG levels were measured (the latter only in the 2 treatment groups). No significant treatment effects were found on any of the measures. There was a significant decrease in the ratings of tinnitus awareness over the assessment occasions, but the degree of change was equivalent for treated and untreated groups. Results do not support the assertion that EMG biofeedback is an effective treatment for tinnitus.