Driving performance on monotonous roads

Driving on motorways has largely been reduced to a lane-keeping task with cruise control. Rapidly, drivers are likely to get bored with such a task and take their attention away from the road. This is of concern in terms of road safety – particularly for professional drivers - since inattention has been identified as one of the main contributing factors to road crashes and is estimated to be involved in 20 to 30% of these crashes. Furthermore, drivers are not aware that their vigilance level has decreased and that their driving performance is impaired. Intelligent Transportation System (ITS) intervention can be used as a countermeasure against vigilance decrement. This paper aims to identify a variety of metrics impacted during monotonous driving - ranging from vehicle data to physiological variables - and relate them to two monotonous factors namely the monotony of the road design (straightness) and the monotony of the environment (landscape, signage, traffic). Data are collected in a driving simulator instrumented with an eye tracking system, a heart rate monitor and an electrodermal activity device (N=25 participants). The two monotonous factors are varied (high and low) leading to the use of four different driving scenarios (40 minutes each). We show with Generalised Linear Mixed Models that driver performance decreases faster when the road is monotonous. We also highlight that road monotony impairs a variety of driving performance and vigilance measures, ranging from speed, lateral position of the vehicle to physiological measurements such as heart rate variability, blink frequency and electrodermal activity. This study informs road designers of the importance of having a varied road environment. It also provides a range of metrics that can be used to detect in real-time the impairment of driving performance on monotonous roads. Such knowledge could result in the development of an in-vehicle device warning drivers at early signs of driving performance impairment on monotonous roads.

Alternate structural system of incorporating flat bed rail wagons as low volume road bridge decks

The stimulus for this project rose from the need to find an alternative solution to aging superstructures of road-bridge in low volume roads (LVR). The solution investigated, designed and consequently plans to construct, involved replacing an aging super-structure of a 10m span bridge with Flat-Bed Rail Wagon (FBRW). The main focus of this paper is to present alternate structural system for the design of the FBRW as road bridge deck conforming to AS5100. The structural adequacy of the primary members of the FBRW was first validated using full scale experimental investigation to AS5100 serviceability and ultimate limit state loading. The bare FBRW was further developed to include a running surface. Two options were evaluated during the design phase, namely timber and reinforced concrete. First option, which is presented here, involved strengthening of the FBRW using numerous steel sections and overlaying the bridge deck with timber planks. The idea of this approach was to use all the primary and secondary members of the FBRW in load sharing and to provide additional members where weaknesses in the original members arose. The second option, which was the preferred option for construction, involved use of primary members only with an overlaying reinforced concrete slab deck. This option minimised the risk associated with any uncertainty of secondary members to its structural adequacy. The paper will report selected results of the experiment as well as the design phases of option one with conclusions highlighting the viability of option 1 and its limitations.

Parental beliefs about supervising children when crossing roads and cycling

Pedestrian and cyclist injuries are significant public health issues together accounting for 11-30% of road deaths in highly motorised countries. Children are particularly at risk. In Australia in 2009 children 0-16 years comprised 11.4% of pedestrian deaths and 6.4% of cyclist deaths. Parental attitudes and level of supervision are important to children’s road safety. Results from a telephone survey with parents of children 5-9 years (N=147) are reported. Questions addressed beliefs about preventability of injury, appropriate ages for children to cross the road or cycle independently, and the frequency of holding 5-9 year old children’s hands while crossing the road. Results suggest that parents believe most injuries are preventable and that they personally can act to improve their own safety in the home, on the road, at work, as well as in or on the water. Most parents (68%) indicated children should be 10 years or older before crossing the road or cycling independently. Parents were more likely to report holding younger children’s hands (5-6 years) when crossing the road and less likely to do so for 7-9 year olds. There was a small effect of child gender, with parents more likely to hold boy’s hand than a girl’s.

Australia experiments with 'experimental use' exemption

Lawmakers are asking whether Australian researchers need an express 'experimental use' defense against patent infringement. The overriding policy for establishing a patent system is indisputably the promotion of innovation. According to traditional intellectual property pedagogy, the incentive to innovate flows from the reward afforded to the inventor. A balancing policy is that the patentee must fully disclose the invention to help minimize the risks of duplication and provides a basis for improvements by further research.Where there is uncertainty as to how these competing policy limbs are balanced and whether a patentee can exclude others from experimenting on a patented invention, the uncertain legal environment disadvantages both the patentee and researcher. Different jurisdictions have treated the experimental use question quite differently with varied results for the researcher. The biotechnology industry is evolving at an unprecedented pace and the law will as is always the case, lag behind in its usual cautious fashion. The Australian law may finally catch up to researchers' concerns.

Experimental evaluation of position control methods for hydraulic systems

Presents a unified and systematic assessment of ten position control strategies for a hydraulic servo system with single-ended cylinder driven by a proportional directional control valve. We aim at identifying those methods that achieve better tracking, have a low sensitivity to system uncertainties, and offer a good balance between development effort and end results. A formal approach for solving this problem relies on several practical metrics, which is introduced herein. Their choice is important, as the comparison results between controllers can vary significantly, depending on the selected criterion. Apart from the quantitative assessment, we also raise aspects which are difficult to quantify, but which must stay in attention when considering the position control problem for this class of hydraulic servo systems.

Is it possible to dissociate ‘liking’ and ‘wanting’ for foods in humans? A novel experimental procedure

Berridge's model (e.g. [Berridge KC. Food reward: Brain substrates of wanting and liking. Neurosci Biobehav Rev 1996;20:1–25.; Berridge KC, Robinson T E. Parsing reward. Trends Neurosci 2003;26:507–513.; Berridge KC. Motivation concepts in behavioral neuroscience. Physiol Behav 2004;81:179–209]) outlines the brain substrates thought to mediate food reward with distinct ‘liking’ (hedonic/affective) and ‘wanting’ (incentive salience/motivation) components. Understanding the dual aspects of food reward could throw light on food choice, appetite control and overconsumption. The present study reports the development of a procedure to measure these processes in humans. A computer-based paradigm was used to assess ‘liking’ (through pleasantness ratings) and ‘wanting’ (through forced-choice photographic procedure) for foods that varied in fat (high or low) and taste (savoury or sweet). 60 participants completed the program when hungry and after an ad libitum meal. Findings indicate a state (hungry–satiated)-dependent, partial dissociation between ‘liking’ and ‘wanting’ for generic food categories. In the hungry state, participants ‘wanted’ high-fat savoury > low-fat savoury with no corresponding difference in ‘liking’, and ‘liked’ high-fat sweet > low-fat sweet but did not differ in ‘wanting’ for these foods. In the satiated state, participants ‘liked’, but did not ‘want’, high-fat savoury > low-fat savoury, and ‘wanted’ but did not ‘like’ low-fat sweet > high-fat sweet. More differences in ‘liking’ and ‘wanting’ were observed when hungry than when satiated. This procedure provides the first step in proof of concept that ‘liking’ and ‘wanting’ can be dissociated in humans and can be further developed for foods varying along different dimensions. Other experimental procedures may also be devised to separate ‘liking’ and ‘wanting’.

Experimental studies on the shear behaviour and strength of LiteSteel Beams

This paper presents the details of an experimental study on the shear behaviour and strength of a recently developed, cold-formed steel hollow flange channel beam known as LiteSteel Beam (LSB). The new LSB sections with rectangular hollow flanges are produced using a patented manufacturing process involving simultaneous cold-forming and dual electric resistance welding. They are commonly used as flexural members in buildings. However, no research has been undertaken on the shear behaviour of LSBs. Therefore a detailed experimental study involving 36 shear tests was undertaken to investigate the shear behaviour of 10 different LSB sections. Simply supported test specimens of LSBs with aspect ratios of 1.0 and 1.5 were loaded at midspan until failure using both single and back to back LSB arrangements. Test specimens were chosen such that all three types of shear failure (shear yielding, inelastic and elastic shear buckling) occurred in the tests. Comparison of experimental results with corresponding predictions from the current Australian and North American cold-formed steel design rules showed that the current design rules are very conservative for the shear design of LSBs. Significant improvements to web shear buckling occurred due to the presence of rectangular hollow flanges while considerable post-buckling strength was also observed. Appropriate improvements have been proposed for the shear strength of LSBs based on the design equations in the North American Specification. This paper presents the details of this experimental study and the results. When reduced height web side plates or only one web side plate was used, the shear capacity of LSB was reduced. Details of these tests and the results are also presented in this paper. Keywords: LiteSteel beam, Shear strength, Shear tests, Cold-formed steel structures, Direct strength method, Slender web, Hollow flanges.

Single case experimental design : an overview

Background: In health related research, it is critical not only to demonstrate the efficacy of intervention, but to show that this is not due to chance or confounding variables. Content: Single case experimental design is a useful quasi-experimental design and method used to achieve these goals when there are limited participants and funds for research. This type of design has various advantages compared to group experimental designs. One such advantage is the capacity to focus on individual performance outcomes compared to group performance outcomes. Conclusions: This comprehensive review demonstrates the benefits and limitations of using single case experimental design, its various design methods, and data collection and analysis for research purposes.

Study of wheel-rail impact at insulated rail joint through experimental and numerical methods

As part of an ongoing research on the development of a longer life insulated rail joint (IRJ), this paper reports a field experiment and a simplified 2D numerical modelling for the purpose of investigating the behaviour of rail web in the vicinity of endpost in an insulated rail joint (IRJ) due to wheel passages. A simplified 2D plane stress finite element model is used to simulate the wheel-rail rolling contact impact at IRJ. This model is validated using data from a strain gauged IRJ that was installed in a heavy haul network; data in terms of the vertical and shear strains at specific positions of the IRJ during train passing were captured and compared with the results of the FE model. The comparison indicates a satisfactory agreement between the FE model and the field testing. Furthermore, it demonstrates that the experimental and numerical analyses reported in this paper provide a valuable datum for developing further insight into the behaviour of IRJ under wheel impacts.