Natural ventilation heuristics in high-rise residential buildings : evaluation and prediction

Complex behaviour of air flow in the buildings makes it difficult to predict. Consequently, architects use common strategies for designing buildings with adequate natural ventilation. However, each climate needs specific strategies and there are not many heuristics for subtropical climate in literature. Furthermore, most of these common strategies are based on low-rise buildings and their performance for high-rise buildings might be different due to the increase of the wind speed with increase in the height. This study uses Computational Fluid Dynamics (CFD) to evaluate these rules of thumb for natural ventilation for multi-residential buildings in subtropical climate. Four design proposals for multi-residential towers with natural ventilation which were produced in intensive two days charrette were evaluated using CFD. The results show that all the buildings reach acceptable level of wind speed in living areas and poor amount of air flow in sleeping areas.

Factors influencing the provision of end-of-life care in critical care settings : development and testing of a survey instrument

Aim. To develop and psychometrically test a survey instrument to identify the factors influencing the provision of end-of-life care by critical care nurses. Background. Following a decision to withdraw life-sustaining treatment, critical care nurses remain with the patient and their family providing end-of-life care. Identification of factors influencing the provision of this care can give evidence to inform practice development and support nurses. Design. A cross-sectional survey of critical care nurses. Method. An online survey was developed, reviewed by an expert panel and pilot tested to obtain preliminary evidence of its reliability and validity. In May 2011, a convenience sample of critical care nurses (n = 392, response rate 25%) completed the survey. The analytical approach to data obtained from the 58 items measured on a Likert scale included exploratory factor analysis and descriptive statistics. Results. Exploratory factor analysis identified eight factors influencing the provision of end-of-life care: emotional support for nurses, palliative values, patient and family preferences, resources, organizational support, care planning, knowledge and preparedness. Internal consistency of each latent construct was deemed satisfactory. The results of descriptive statistics revealed a strong commitment to the inclusion of families in end-of-life care and the value of this care in the critical care setting. Conclusion. This paper reports preliminary evidence of the psychometric properties of a new survey instrument. The findings may inform practice development opportunities to support critical care nurses in the provision of endof- life care and improve the care that patients and their families receive.

Modelling collision potentials in Port Anchorages: Application of the Navigational Traffic Conflict Technique (NTCT)

Despite the extent of works done on modelling port water collisions, not much research effort has been devoted to modelling collisions at port anchorages. This paper aims to fill this important gap in literature by applying the Navigation Traffic Conflict Technique (NTCT) for measuring the collision potentials in anchorages and for examining the factors contributing to collisions. Grounding on the principles of the NTCT, a collision potential measurement model and a collision potential prediction model were developed. These models were illustrated by using vessel movement data of the anchorages in Singapore port waters. Results showed that the measured collision potentials are in close agreement with those perceived by harbour pilots. Higher collision potentials were found in anchorages attached to shoreline and international fairways, but not at those attached to confined water. Higher operating speeds, larger numbers of isolated danger marks and day conditions were associated with reduction in the collision potentials.

Flexible Ag electrode for use in organic photovoltaics

High efficiency organic photovoltaic cells discussed in literature are normally restricted to devices fabricated on glass substrates. This is a consequence of the extreme brittleness and inflexibility of the commonly used transparent conductive oxide electrode, indium tin oxide (ITO). This shortcoming of ITO along with other concerns such as increasing scarcity of indium, migration of indium to organic layer, etc. makes it imperative to move away from ITO. Here we demonstrate a highly flexible Ag electrode that possesses low sheet resistances even in ultra-thin layers. It retains its conductivity under severe bending stresses where ITO fails completely. A P3HT:PCBM blend organic solar cell fabricated on this highly flexible electrode gives an efficiency of 2.3%.

Communication adaption in challenging simulations for student nurse midwives

Background Nurses and midwives must be able to adapt their behaviour and language to meet the health care needs of patients and their families in diverse and at times difficult circumstances. Methods This study of fourth year dual degree nurse midwives use Communication Accommodation Theory strategies to examine their use of language and discourse when managing a sequential simulation of neonatal resuscitation and bereavement support. Results The results showed that many of the students were slow to respond to the changing needs of the patient and family and at times used ineffectual and disengaging language. Conclusion Clinical simulation is a safe and effective method for nurses and midwives to experience and practice the use of language and discourse in challenging circumstances.

Robust principal component analysis in water quality index development

Some statistical procedures already available in literature are employed in developing the water quality index, WQI. The nature of complexity and interdependency that occur in physical and chemical processes of water could be easier explained if statistical approaches were applied to water quality indexing. The most popular statistical method used in developing WQI is the principal component analysis (PCA). In literature, the WQI development based on the classical PCA mostly used water quality data that have been transformed and normalized. Outliers may be considered in or eliminated from the analysis. However, the classical mean and sample covariance matrix used in classical PCA methodology is not reliable if the outliers exist in the data. Since the presence of outliers may affect the computation of the principal component, robust principal component analysis, RPCA should be used. Focusing in Langat River, the RPCA-WQI was introduced for the first time in this study to re-calculate the DOE-WQI. Results show that the RPCA-WQI is capable to capture similar distribution in the existing DOE-WQI.

A genome-wide association study of caffeine-related sleep disturbance: Confirmation of a role for a common variant in the adenosine receptor

OBJECTIVES To identify common genetic variants that predispose to caffeine-induced insomnia and to test whether genes whose expression changes in the presence of caffeine are enriched for association with caffeine-induced insomnia. DESIGN A hypothesis-free, genome-wide association study. SETTING Community-based sample of Australian twins from the Australian Twin Registry. PARTICIPANTS After removal of individuals who said that they do not drink coffee, a total of 2,402 individuals from 1,470 families in the Australian Twin Registry provided both phenotype and genotype information. MEASUREMENTS AND RESULTS A dichotomized scale based on whether participants reported ever or never experiencing caffeine-induced insomnia. A factor score based on responses to a number of questions regarding normal sleep habits was included as a covariate in the analysis. More than 2 million common single nucleotide polymorphisms (SNPs) were tested for association with caffeine-induced insomnia. No SNPs reached the genome-wide significance threshold. In the analysis that did not include the insomnia factor score as a covariate, the most significant SNP identified was an intronic SNP in the PRIMA1 gene (P = 1.4 x 10(-)(6), odds ratio = 0.68 [0.53 - 0.89]). An intergenic SNP near the GBP4 gene on chromosome 1 was the most significant upon inclusion of the insomnia factor score into the model (P = 1.9 x 10(-)(6), odds ratio = 0.70 [0.62 - 0.78]). A previously identified association with a polymorphism in the ADORA2A gene was replicated. CONCLUSIONS Several genes have been identified in the study as potentially influencing caffeine-induced insomnia. They will require replication in another sample. The results may have implications for understanding the biologic mechanisms underlying insomnia.

A model of factors that influence meeting the needs of family with a relative in ICU

This thesis developed a model of factors that influence meeting the needs of family with a relative admitted to an adult intensive care unit. The results from the model indicate that several variables are significant in meeting the needs of families in ICU. The factors identified in this study should be considered when planning future intervention studies or implementing interventions into ICU clinical practice. Meeting the needs of families is an integral part of caring for a critically ill patient. ICU staff can minimise this stressful time for relatives by anticipating and addressing family needs.

Identification and analysis of business and software services : A consolidated approach

Although the benefits of service orientation are prevalent in literature, a review, analysis, and evaluation of the 30 existing service analysis approaches presented in this paper have shown that a comprehensive approach to the identification and analysis of both business and supporting software services is missing. Based on this evaluation of existing approaches and additional sources, we close this gap by proposing an integrated, consolidated approach to business and software service analysis that combines and extends the strengths of the examined methodologies.

Review of strengthening techniques using externally bonded fiber reinforced polymer composites

This report reviews the selection, design, and installation of fiber reinforced polymer systems for strengthening of reinforced concrete or pre-stressed concrete bridges and other structures. The report is prepared based on the knowledge gained from worldwide experimental research, analytical work, and field applications of FRP systems used to strengthen concrete structures. Information on material properties, design and installation methods of FRP systems used as external reinforcement are presented. This information can be used to select an FRP system for increasing the strength and stiffness of reinforced concrete beams or the ductility of columns, and other applications. Based on the available research, the design considerations and concepts are covered in this report. In the next stage of the project, these will be further developed as design tools. It is important to note, however, that the design concepts proposed in literature have not in many cases been thoroughly developed and proven. Therefore, a considerable amount of research work will be required prior to development of the design concepts into practical design tools, which is a major goal of the current research project. The durability and long-term performance of FRP materials has been the subject of much research, which still are on going. Long-term field data are not currently available, and it is still difficult to accurately predict the life of FRP strengthening systems. The report briefly addresses environmental degradation and long-term durability issues as well. A general overview of using FRP bars as primary reinforcement of concrete structures is presented in Chapter 8. In Chapter 9, a summary of strengthening techniques identified as part of this initial stage of the research project and the issues which require careful consideration prior to practical implementation of these identified techniques are presented.

Value creation and value capture fro open source software publisher : a new business model based on mutualisation

Key topics: Since the birth of the Open Source movement in the mid-80's, open source software has become more and more widespread. Amongst others, the Linux operating system, the Apache web server and the Firefox internet explorer have taken substantial market shares to their proprietary competitors. Open source software is governed by particular types of licenses. As proprietary licenses only allow the software's use in exchange for a fee, open source licenses grant users more rights like the free use, free copy, free modification and free distribution of the software, as well as free access to the source code. This new phenomenon has raised many managerial questions: organizational issues related to the system of governance that underlie such open source communities (Raymond, 1999a; Lerner and Tirole, 2002; Lee and Cole 2003; Mockus et al. 2000; Tuomi, 2000; Demil and Lecocq, 2006; O'Mahony and Ferraro, 2007;Fleming and Waguespack, 2007), collaborative innovation issues (Von Hippel, 2003; Von Krogh et al., 2003; Von Hippel and Von Krogh, 2003; Dahlander, 2005; Osterloh, 2007; David, 2008), issues related to the nature as well as the motivations of developers (Lerner and Tirole, 2002; Hertel, 2003; Dahlander and McKelvey, 2005; Jeppesen and Frederiksen, 2006), public policy and innovation issues (Jullien and Zimmermann, 2005; Lee, 2006), technological competitions issues related to standard battles between proprietary and open source software (Bonaccorsi and Rossi, 2003; Bonaccorsi et al. 2004, Economides and Katsamakas, 2005; Chen, 2007), intellectual property rights and licensing issues (Laat 2005; Lerner and Tirole, 2005; Gambardella, 2006; Determann et al., 2007). A major unresolved issue concerns open source business models and revenue capture, given that open source licenses imply no fee for users. On this topic, articles show that a commercial activity based on open source software is possible, as they describe different possible ways of doing business around open source (Raymond, 1999; Dahlander, 2004; Daffara, 2007; Bonaccorsi and Merito, 2007). These studies usually look at open source-based companies. Open source-based companies encompass a wide range of firms with different categories of activities: providers of packaged open source solutions, IT Services&Software Engineering firms and open source software publishers. However, business models implications are different for each of these categories: providers of packaged solutions and IT Services&Software Engineering firms' activities are based on software developed outside their boundaries, whereas commercial software publishers sponsor the development of the open source software. This paper focuses on open source software publishers' business models as this issue is even more crucial for this category of firms which take the risk of investing in the development of the software. Literature at last identifies and depicts only two generic types of business models for open source software publishers: the business models of ''bundling'' (Pal and Madanmohan, 2002; Dahlander 2004) and the dual licensing business models (Välimäki, 2003; Comino and Manenti, 2007). Nevertheless, these business models are not applicable in all circumstances. Methodology: The objectives of this paper are: (1) to explore in which contexts the two generic business models described in literature can be implemented successfully and (2) to depict an additional business model for open source software publishers which can be used in a different context. To do so, this paper draws upon an explorative case study of IdealX, a French open source security software publisher. This case study consists in a series of 3 interviews conducted between February 2005 and April 2006 with the co-founder and the business manager. It aims at depicting the process of IdealX's search for the appropriate business model between its creation in 2000 and 2006. This software publisher has tried both generic types of open source software publishers' business models before designing its own. Consequently, through IdealX's trials and errors, I investigate the conditions under which such generic business models can be effective. Moreover, this study describes the business model finally designed and adopted by IdealX: an additional open source software publisher's business model based on the principle of ''mutualisation'', which is applicable in a different context. Results and implications: Finally, this article contributes to ongoing empirical work within entrepreneurship and strategic management on open source software publishers' business models: it provides the characteristics of three generic business models (the business model of bundling, the dual licensing business model and the business model of mutualisation) as well as conditions under which they can be successfully implemented (regarding the type of product developed and the competencies of the firm). This paper also goes further into the traditional concept of business model used by scholars in the open source related literature. In this article, a business model is not only considered as a way of generating incomes (''revenue model'' (Amit and Zott, 2001)), but rather as the necessary conjunction of value creation and value capture, according to the recent literature about business models (Amit and Zott, 2001; Chresbrough and Rosenblum, 2002; Teece, 2007). Consequently, this paper analyses the business models from these two components' point of view.

Self-commutated current source converter with multi-level current reinjection

The multi-level current reinjection concept described in literature is well-known to produce high quality AC current waveforms in high power and high voltage self-commutating current source converters. This paper proposes a novel reinjection circuitry which is capable of producing a 7-level reinjection current. It is shown that this reinjection current effectively increases the pulse number of the converter to 72. The use of PSCAD/EMTDC simulation validates the functionality of the proposed concept illustrating its effectiveness on both AC and DC sides of the converter.

Downtime reduction analysis of the Australia Post flat mail optical character reader

Machine downtime, whether planned or unplanned, is intuitively costly to manufacturing organisations, but is often very difficult to quantify. The available literature showed that costing processes are rarely undertaken within manufacturing organisations. Where cost analyses have been undertaken, they generally have only valued a small proportion of the affected costs, leading to an overly conservative estimate. This thesis aimed to develop a cost of downtime model, with particular emphasis on the application of the model to Australia Post’s Flat Mail Optical Character Reader (FMOCR). The costing analysis determined a cost of downtime of $5,700,000 per annum, or an average cost of $138 per operational hour. The second section of this work focused on the use of the cost of downtime to objectively determine areas of opportunity for cost reduction on the FMOCR. This was the first time within Post that maintenance costs were considered along side of downtime for determining machine performance. Because of this, the results of the analysis revealed areas which have historically not been targeted for cost reduction. Further exploratory work was undertaken on the Flats Lift Module (FLM) and Auto Induction Station (AIS) Deceleration Belts through the comparison of the results against two additional FMOCR analysis programs. This research has demonstrated the development of a methodical and quantifiable cost of downtime for the FMOCR. This has been the first time that Post has endeavoured to examine the cost of downtime. It is also one of the very few methodologies for valuing downtime costs that has been proposed in literature. The work undertaken has also demonstrated how the cost of downtime can be incorporated into machine performance analysis with specific application to identifying high costs modules. The outcome of this report has both been the methodology for costing downtime, as well as a list of areas for cost reduction. In doing so, this thesis has outlined the two key deliverables presented at the outset of the research.