Prediction of masonry compressive behaviour using a damage mechanics inspired modelling method

Masonry under compression is affected by the properties of its constituents and their interfaces. In spite of extensive investigations of the behaviour of masonry under compression, the information in the literature cannot be regarded as comprehensive due to ongoing inventions of new generation products – for example, polymer modified thin layer mortared masonry and drystack masonry. As comprehensive experimental studies are very expensive, an analytical model inspired by damage mechanics is developed and applied to the prediction of the compressive behaviour of masonry in this paper. The model incorporates a parabolic progressively softening stress-strain curve for the units and a progressively stiffening stress-strain curve until a threshold strain for the combined mortar and the unit-mortar interfaces is reached. The model simulates the mutual constraints imposed by each of these constituents through their respective tensile and compressive behaviour and volumetric changes. The advantage of the model is that it requires only the properties of the constituents and considers masonry as a continuum and computes the average properties of the composite masonry prisms/wallettes; it does not require discretisation of prism or wallette similar to the finite element methods. The capability of the model in capturing the phenomenological behaviour of masonry with appropriate elastic response, stiffness degradation and post peak softening is presented through numerical examples. The fitting of the experimental data to the model parameters is demonstrated through calibration of some selected test data on units and mortar from the literature; the calibrated model is shown to predict the responses of the experimentally determined masonry built using the corresponding units and mortar quite well. Through a series of sensitivity studies, the model is also shown to predict the masonry strength appropriately for changes to the properties of the units and mortar, the mortar joint thickness and the ratio of the height of unit to mortar joint thickness. The unit strength is shown to affect the masonry strength significantly. Although the mortar strength has only a marginal effect, reduction in mortar joint thickness is shown to have a profound effect on the masonry strength. The results obtained from the model are compared with the various provisions in the Australian Masonry Structures Standard AS3700 (2011) and Eurocode 6.

A pilot education on heart failure self-management and introduction of the teach-back method to cardiac nurses in Vietnam

It is recognised that patients with chronic disease are unable to remembercorrectly information provided by health care profesionals. The teach-back method is acknowledgedas a technique to improve patients’ understanding. Yet it is not used in nursing practice in Vietnam. Objectives This study sought to examine knowledge background of heart failure among cardiac nurses, introduce a education about heart failure self-management and the teach-back method to assist teaching patients on self-care. The study also wanted to explore if a short education could benefit nurses’ knowledge so they would be qualified to deliver education to patients. Methods A pre/post-test design was employed. Cardiac nurses from 3 hospitals (Vietnam National Heart Institute, E Hospital, Huu Nghi Hospital) were invited to attend a six-hour educational session which covered both the teach-back method and heart failure self-management. Role-play with scenarios were used to reinforce educational contents. The Dutch Heart Failure Knowledge Scale was used to assess nurses’ knowledge of heart failure at baseline and after the educational session. Results 20 nurses from3 selected hospitals participated. Average age was 34.5±7.9 years and years of nursing experience was 11.6±8.3. Heart failure knowledge score at the baseline was 12.7±1.2 and post education was 13.8±1.0. There was deficiency of nurses knowledge regarding fluid restriction among heart failure people, causes of worsening heart failure. Heart failure knowledge improved significantly following the workshop (p < 0.001). All nurses achieved an overall adequate knowledge score (≥11 of the maximum 15) at the end. 100% of nurses agreed that the teach-back method was effective and could be used to educate patients about heart failure self-management. Conclusions The results of this study have shown the effectiveness of the piloteducaiton in increasing nurses’ knowledge of heart failure. The teach-back method is accepted for Vietnamese nurses to use in routine cardiac practice.

The effectiveness of the teach-back method on adherence and self-management in health education for people with chronic disease: A systematic review

- BACKGROUND Chronic diseases are increasing worldwide and have become a significant burden to those affected by those diseases. Disease-specific education programs have demonstrated improved outcomes, although people do forget information quickly or memorize it incorrectly. The teach-back method was introduced in an attempt to reinforce education to patients. To date, the evidence regarding the effectiveness of health education employing the teach-back method in improved care has not yet been reviewed systematically. - OBJECTIVES This systematic review examined the evidence on using the teach-back method in health education programs for improving adherence and self-management of people with chronic disease. - INCLUSION CRITERIA Types of participants: Adults aged 18 years and over with one or more than one chronic disease. Types of intervention: All types of interventions which included the teach-back method in an education program for people with chronic diseases. The comparator was chronic disease education programs that did not involve the teach-back method. Types of studies: Randomized and non-randomized controlled trials, cohort studies, before-after studies and case-control studies. Types of outcomes: The outcomes of interest were adherence, self-management, disease-specific knowledge, readmission, knowledge retention, self-efficacy and quality of life. - SEARCH STRATEGY Searches were conducted in CINAHL, MEDLINE, EMBASE, Cochrane CENTRAL, Web of Science, ProQuest Nursing and Allied Health Source, and Google Scholar databases. Search terms were combined by AND or OR in search strings. Reference lists of included articles were also searched for further potential references. - METHODOLOGICAL QUALITY Two reviewers conducted quality appraisal of papers using the Joanna Briggs Institute Meta-Analysis of Statistics Assessment and Review Instrument. - DATA EXTRACTION Data were extracted using the Joanna Briggs Institute Meta-Analysis of Statistics Assessment and Review Instrument data extraction instruments. - DATA SYNTHESIS There was significant heterogeneity in selected studies, hence a meta-analysis was not possible and the results were presented in narrative form. - RESULTS Of the 21 articles retrieved in full, 12 on the use of the teach-back method met the inclusion criteria and were selected for analysis. Four studies confirmed improved disease-specific knowledge in intervention participants. One study showed a statistically significant improvement in adherence to medication and diet among type 2 diabetics patients in the intervention group compared to the control group (p < 0.001). Two studies found statistically significant improvements in self-efficacy (p = 0.0026 and p < 0.001) in the intervention groups. One study examined quality of life in heart failure patients but the results did not improve from the intervention (p = 0.59). Five studies found a reduction in readmission rates and hospitalization but these were not always statistically significant. Two studies showed improvement in daily weighing among heart failure participants, and in adherence to diet, exercise and foot care among those with type 2 diabetes. - CONCLUSION Overall, the teach-back method showed positive effects in a wide range of health care outcomes although these were not always statistically significant. Studies in this systematic review revealed improved outcomes in disease-specific knowledge, adherence, self-efficacy and the inhaler technique. There was a positive but inconsistent trend also seen in improved self-care and reduction of hospital readmission rates. There was limited evidence on improvement in quality of life or disease related knowledge retention.

The doctrinal method: Incorporating interdisciplinary methods in reforming the law

The doctrinal methodology is in a period of change and transition. Realising that the scope of the doctrinal method is too constricting, academic lawyers are becoming eclectic in their use of research method. In this transitional time, legal scholars are increasingly infusing evidence (and methods) from other disciplines into their reasoning to bolster their reform recommendations. This article considers three examples of the interplay of the discipline of law with other disciplines in the pursuit of law reform. Firstly the article reviews studies on the extent of methodologies and reformist frameworks in PhD research in Australia. Secondly it analyses a ‘snapshot’ of recently published Australian journal articles on criminal law reform. Thirdly, it focuses on the law reform commissions, those independent government committees that play such an important role in law reform in common law jurisdictions. This examination demonstrates that while the doctrinal core of legal scholarship remains intact, legal scholars are endeavouring to accommodate statistics, comparative perspectives, social science evidence and methods, and theoretical analysis, within the legal research framework, in order to provide additional ballast to the recommendations for reform.

Formal network behaviour analysis using model checking

In this research we modelled computer network devices to ensure their communication behaviours meet various network standards. By modelling devices as finite-state machines and examining their properties in a range of configurations, we discovered a flaw in a common network protocol and produced a technique to improve organisations' network security against data theft.

Sovereignty, surveillance and speeding: Considering the Panopticon as a method of policing

This paper argues that the Panopticon is an accurate model for and illustration of policing and security methods in the modern society. Initially, I overview the theoretical concept of the Panopticon as a structure of perceived universal surveillance which facilitates automatic obedience in its subjects as identified by the theorists Jeremy Bentham and Michel Foucault. The paper subsequently moves to identify how the Panopticon, despite being a theoretical construct, is nevertheless instantiated to an extent through the prevalence of security cameras as a means of sovereignly regulating human conduct; speeding is an ordinary example. It could even be contended that increasing surveillance according to the model of the Panopticon would reduce the frequency of offences. However, in the final analysis the paper considers that even if adopting an approach based on the Panopticon is a more effective method of policing, it is not necessarily a more desirable one.

Formal security analysis of the DNP3-secure authentication protocol

This thesis evaluates the security of Supervisory Control and Data Acquisition (SCADA) systems, which are one of the key foundations of many critical infrastructures. Specifically, it examines one of the standardised SCADA protocols called the Distributed Network Protocol Version 3, which attempts to provide a security mechanism to ensure that messages transmitted between devices, are adequately secured from rogue applications. To achieve this, the thesis applies formal methods from theoretical computer science to formally analyse the correctness of the protocol.

Single layer graphene film by ethanol chemical vapor deposition: Highly efficient growth and clean transfer method

The choice of ethanol (C2H5OH) as carbon source in the Chemical Vapor Deposition (CVD) of graphene on copper foils can be considered as an attractive alternative among the commonly used hydrocarbons, such as methane (CH4) [1]. Ethanol, a safe, low cost and easy handling liquid precursor, offers fast and efficient growth kinetics with the synthesis of fullyformed graphene films in just few seconds [2]. In previous studies of graphene growth from ethanol, various research groups explored temperature ranges lower than 1000 °C, usually reported for methane-assisted CVD. In particular, the 650–850 °C and 900 °C ranges were investigated, respectively for 5 and 30 min growth time [3, 4]. Recently, our group reported the growth of highly-crystalline, few-layer graphene by ethanol-CVD in hydrogen flow (1– 100 sccm) at high temperatures (1000–1070 °C) using growth times typical of CH4-assisted synthesis (10–30 min) [5]. Furthermore, a synthesis time between 20 and 60 s in the same conditions was explored too. In such fast growth we demonstrated that fully-formed graphene films can be grown by exposing copper foils to a low partial pressure of ethanol (up to 2 Pa) in just 20 s [6] and we proposed that the rapid growth is related to an increase of the Cu catalyst efficiency due weak oxidizing nature of ethanol. Thus, the employment of such liquid precursor, in small concentrations, together with a reduced time of growth and very low pressure leads to highly efficient graphene synthesis. By this way, the complete coverage of a copper catalyst surface with high spatial uniformity can be obtained in a considerably lower time than when using methane.

A novel fully validated LC–MS/MS method for quantification of pyridoxal-5′-phosphate concentrations in samples of human whole blood

Quantification of pyridoxal-5´-phosphate (PLP) in biological samples is challenging due to the presence of endogenous PLP in matrices used for preparation of calibrators and quality control samples (QCs). Hence, we have developed an LC-MS/MS method for accurate and precise measurement of the concentrations of PLP in samples (20 µL) of human whole blood that addresses this issue by using a surrogate matrix and minimizing the matrix effect. We used a surrogate matrix comprising 2% bovine serum albumin (BSA) in phosphate buffer saline (PBS) for making calibrators, QCs and the concentrations were adjusted to include the endogenous PLP concentrations in the surrogate matrix according to the method of standard addition. PLP was separated from the other components of the sample matrix using protein precipitation with trichloroacetic acid 10% w/v. After centrifugation, supernatant were injected directly into the LC-MS/MS system. Calibration curves were linear and recovery was > 92%. QCs were accurate, precise, stable for four freeze-thaw cycles, and following storage at room temperature for 17h or at -80 °C for 3 months. There was no significant matrix effect using 9 different individual human blood samples. Our novel LC-MS/MS method has satisfied all of the criteria specified in the 2012 EMEA guideline on bioanalytical method validation.

BaZr0.8Y0.2O3--NiO composite anodic powders for proton-conducting SOFCs prepared by a combustion method

BaZr0.8Y0.2O3- (BZY)-NiO composite powders with different BZY-NiO weight ratios were prepared by a combustion method as anodes for proton-conducting solid oxide fuel cells (SOFCs). After heating to 1100C for 6 h, the composite powders were made of a well-dispersed mixture of two phases, BZY and NiO. Chemical stability tests showed that the BZY-NiO anodic powders had good stability against CO2, whereas comparative tests under the same conditions showed degradation for BaCe0.7Zr 0.1Y0.2O3--NiO, which is at present the most used anode material for proton-conducting SOFCs. Area specific resistance (ASR) measurements for BZY-NiO anodes showed that their electrochemical performance depended on the BZY-NiO weight ratio. The best performance was obtained for the anode containing 50 wt BZY and 50 wt NiO, which showed the smallest ASR values in the whole testing temperature range (0.37 cm2 at 600C). The 50 wt BZY and 50 wt NiO anode prepared by combustion also showed superior performance than that of the BZY-NiO anode conventionally made by a mechanical mixing route, as well as that of Pt.

Assessing clinical reasoning: A method to monitor its development in a PBL curriculum

The aim of this study was to develop and trial a method to monitor the evolution of clinical reasoning in a PBL curriculum that is suitable for use in a large medical school. Termed Clinical Reasoning Problems (CRPs), it is based on the notion that clinical reasoning is dependent on the identification and correct interpretation of certain critical clinical features. Each problem consists of a clinical scenario comprising presentation, history and physical examination. Based on this information, subjects are asked to nominate the two most likely diagnoses and to list the clinical features that they considered in formulating their diagnoses, indicating whether these features supported or opposed the nominated diagnoses. Students at different levels of medical training completed a set of 10 CRPs as well as the Diagnostic Thinking Inventory, a self-reporting questionnaire designed to assess reasoning style. Responses were scored against those of a reference group of general practitioners. Results indicate that the CRPs are an easily administered, reliable and valid assessment of clinical reasoning, able to successfully monitor its development throughout medical training. Consequently, they can be employed to assess clinical reasoning skill in individual students and to evaluate the success of undergraduate medical schools in providing effective tuition in clinical reasoning.

Modelling Cued-Target Recall using Quantum Inspired Models of Target Activation

This article presents and evaluates Quantum Inspired models of Target Activation using Cued-Target Recall Memory Modelling over multiple sources of Free Association data. Two components were evaluated: Whether Quantum Inspired models of Target Activation would provide a better framework than their classical psychological counterparts and how robust these models are across the different sources of Free Association data. In previous work, a formal model of cued-target recall did not exist and as such Target Activation was unable to be assessed directly. Further to that, the data source used was suspected of suffering from temporal and geographical bias. As a consequence, Target Activation was measured against cued-target recall data as an approximation of performance. Since then, a formal model of cued-target recall (PIER3) has been developed [10] with alternative sources of data also becoming available. This allowed us to directly model target activation in cued-target recall with human cued-target recall pairs and use multiply sources of Free Association Data. Featural Characteristics known to be important to Target Activation were measured for each of the data sources to identify any major differences that may explain variations in performance for each of the models. Each of the activation models were used in the PIER3 memory model for each of the data sources and was benchmarked against cued-target recall pairs provided by the University of South Florida (USF). Two methods where used to evaluate performance. The first involved measuring the divergence between the sets of results using the Kullback Leibler (KL) divergence with the second utilizing a previous statistical analysis of the errors [9]. Of the three sources of data, two were sourced from human subjects being the USF Free Association Norms and the University of Leuven (UL) Free Association Networks. The third was sourced from a new method put forward by Galea and Bruza, 2015 in which pseudo Free Association Networks (Corpus Based Association Networks - CANs) are built using co-occurrence statistics on large text corpus. It was found that the Quantum Inspired Models of Target Activation not only outperformed the classical psychological model but was more robust across a variety of data sources.

Workplace training and generic and technical skill development in the Australian construction industry

- Purpose The purpose of this paper is to investigate the current skills gap in both generic and skill areas within the construction industry in Queensland, Australia. - Design/methodology/approach An internet-based survey was administered to collect the opinions of construction employees about the workplace-training environment and their perceptions towards training. The survey intended to address the following research questions, specifically in relation to the construction industry. - Findings The survey results reveal that whilst overall participation in workplace training is high, the current workplace training environments do not foster balanced skill development. The study reveals that in the current absence of a formal and well-balanced training mechanism, construction workers generally resort to their own informal self-development initiatives to develop the needed role-specific theoretical knowledge. - Research limitations/implications The findings of the research are based on the data primarily collected in the construction industry in Queensland, Australia. The data are limited to a single Tier 2 construction company. - Practical implications The findings of this study can be utilised to suggest improvements in the current (or develop new) workplace training initiatives. - Social implications The research suggests that workplace training has positive relationship with career growth. The results suggest that in the construction industry, employees are generally well aware of the importance of workplace training in their career development and they largely appreciate training as being a critical factor for developing their capacity to perform their roles successfully, and to maintain their employability. - Originality/value This paper is unique as it investigates the current skills gap in both generic and skill areas within the construction industry in Queensland, Australia. So far no work has been undertaken to identify and discusses the main method of workplace learning within the Tier 2 industry in the context of Queensland Australia.