Drinking and driving in Vietnam : perceptions and risk

Road traffic injuries are a major global public health problem but continue to receive inadequate attention. Alcohol influences both risk and consequence of road traffic injury but the scale of the problem is not well understood in many countries. In Vietnam, economic development has brought a substantial increase in the number of registered motorcycles as well as alcohol consumption. Traffic injury is among the leading causes of death in Vietnam but there is little local information regarding alcohol related traffic injuries. The primary goal of this study is to explore the drinking and driving patterns of males and their perceptions towards drink-driving and to determine the relationship between alcohol consumption and road traffic injuries. Furthermore, this thesis aims to present the situation analysis for choosing priority actions to reduce drinking and driving in Vietnam. The study is a combination of two cross-sectional surveys and a pilot study. The pilot study, involving 224 traffic injured patients, was conducted to test the tools and the feasibility of approach methods. In the first survey, male patrons (n=464) were randomly selected at seven restaurants. Face-to-face interviews were conducted when patrons just arrived and breath tests were collected when they were about to leave the restaurant. In the second survey, male patients admitted to hospital following a traffic injury (n=480, of which 414 were motorcycle or bicycle riders) were interviewed and their blood alcohol concentration (BAC) measured by breathalyzer. The results show broadly similar patterns of drinking and driving among male patrons and male traffic injured patients with a high frequency of drinking and drink-driving reported among the majority of the two groups. A high proportion of male patrons were leaving restaurants with a BAC over the legal limit. Factors that significantly associate with the number of drinks and BAC were age, hazardous drinking, frequency of drink-driving in the past year, self-estimated number of drinks consumed to drive legally, perceived family’s disapproval of drink-driving, and perceived legal risk and physical risk. The proportion of patrons and patients with BAC above the legal limit of 0.05 were 86.7% and 60.4% respectively, which was much higher than found in previous studies. In addition, both groups had a high prevalence of BAC over 0.15g/100ml (39.7% of patrons and 45.6% patients), a level that can seriously affect driving capacity. Results from the case-crossover analysis for patients indicate a dose-response relationship between alcohol consumption and the risk of traffic injury. The risk of traffic injury increased when alcohol was consumed before driving and there was a more than 13 fold increase when six or more drinks were consumed. Regarding perceptions towards drinking and driving, findings corroborate the low awareness among males in Vietnam, with a majority of respondents holding a low knowledge of safe and legally permissible alcohol use, and a low perceived risk of drinking and driving. The results also indicate a huge gap in prevention skills in terms of planning ahead or using alternative transport to avoid drink-driving and a perception by patrons and patients of a low rate of disapproval of drink-driving from peers and family. Findings in this study have considerable implications for national policy, injury prevention, clinical practice, reporting systems, and for further research. The low rate of compliance with existing laws and a generally low perceived legal risk toward drink-driving in this study call for the strengthening of enforcement along with mass media campaigns and news coverage in order to decrease the widespread perception of impunity and thereby, to reduce the level of drink-driving. In addition, no significant difference was found in this study on risk of traffic injuries between car drivers and motorcycle drivers. The current inconsistency between legal BAC for drivers of motorcycles, compared to cars, thus needs addressing. Furthermore, as drinking was found to be very common, rather than solely targeting drink-driving, it is important to call for a more strategic and comprehensive approach to alcohol policy in Viet Nam. This study also has considerable implications for clinical practice in terms of screening and brief interventions. Our study suggests that the short form of the AUDIT (AUDIT-C) screening tool is appropriate for use in busy emergency departments. The high proportion of traffic injured patients with evidence of alcohol abuse or hazardous drinking suggests that brief interventions by alcohol and drug counselors in emergency departments are a sensible option to addressing this important problem. The significance of this study is in the combination of the systematic collection of breath test and use of case-crossover design to estimate the risk of traffic injuries after alcohol consumption. The results provide convincing evidence to policy makers, health authorities and the media to help raise community awareness and policy advocacy toward the drinkdriving problem in Vietnam. The findings suggest an urgent need for a multi-sectoral approach to curtail drink-driving in Vietnam, especially programs to raise community awareness and effective legal enforcement. Furthermore, serving as a situation analysis, the thesis should inform the formulation of interventions designed to curtail drinking and driving in Vietnam and other developing countries.

Planning volunteer responses to low-volume mass gatherings: do event characteristics predict patient workload?

INTRODUCTION: Workforce planning for first aid and medical coverage of mass gatherings is hampered by limited research. In particular, the characteristics and likely presentation patterns of low-volume mass gatherings of between several hundred to several thousand people are poorly described in the existing literature. OBJECTIVES: This study was conducted to: 1. Describe key patient and event characteristics of medical presentations at a series of mass gatherings, including events smaller than those previously described in the literature; 2. Determine whether event type and event size affect the mean number of patients presenting for treatment per event, and specifically, whether the 1:2,000 deployment rule used by St John Ambulance Australia is appropriate; and 3. Identify factors that are predictive of injury at mass gatherings. METHODS: A retrospective, observational, case-series design was used to examine all cases treated by two Divisions of St John Ambulance (Queensland) in the greater metropolitan Brisbane region over a three-year period (01 January 2002-31 December 2004). Data were obtained from routinely collected patient treatment forms completed by St John officers at the time of treatment. Event-related data (e.g., weather, event size) were obtained from event forms designed for this study. Outcome measures include: total and average number of patient presentations for each event; event type; and event size category. Descriptive analyses were conducted using chi-square tests, and mean presentations per event and event type were investigated using Kruskal-Wallis tests. Logistic regression analyses were used to identify variables independently associated with injury presentation (compared with non-injury presentations). RESULTS: Over the three-year study period, St John Ambulance officers treated 705 patients over 156 separate events. The mean number of patients who presented with any medical condition at small events (less than or equal to 2,000 attendees) did not differ significantly from that of large (>2,000 attendees) events (4.44 vs. 4.67, F = 0.72, df = 1, 154, p = 0.79). Logistic regression analyses indicated that presentation with an injury compared with non-injury was independently associated with male gender, winter season, and sporting events, even after adjusting for relevant variables. CONCLUSIONS: In this study of low-volume mass gatherings, a similar number of patients sought medical treatment at small (<2,000 patrons) and large (>2,000 patrons) events. This demonstrates that for low-volume mass gatherings, planning based solely on anticipated event size may be flawed, and could lead to inappropriate levels of first-aid coverage. This study also highlights the importance of considering other factors, such as event type and patient characteristics, when determining appropriate first-aid resourcing for low-volume events. Additionally, identification of factors predictive of injury presentations at mass gatherings has the potential to significantly enhance the ability of event coordinators to plan effective prevention strategies and response capability for these events.

The use of semantic priming as a paradigm for the detection of faking on self-report psychological tests

It is recognised that individuals do not always respond honestly when completing psychological tests. One of the foremost issues for research in this area is the inability to detect individuals attempting to fake. While a number of strategies have been identified in faking, a commonality of these strategies is the latent role of long term memory. Seven studies were conducted in order to examine whether it is possible to detect the activation of faking related cognitions using a lexical decision task. Study 1 found that engagement with experiential processing styles predicted the ability to fake successfully, confirming the role of associative processing styles in faking. After identifying appropriate stimuli for the lexical decision task (Studies 2A and 2B), Studies 3 to 5 examined whether a cognitive state of faking could be primed and subsequently identified, using a lexical decision task. Throughout the course of these studies, the experimental methodology was increasingly refined in an attempt to successfully identify the relevant priming mechanisms. The results were consistent and robust throughout the three priming studies: faking good on a personality test primed positive faking related words in the lexical decision tasks. Faking bad, however, did not result in reliable priming of negative faking related cognitions. To more completely address potential issues with the stimuli and the possible role of affective priming, two additional studies were conducted. Studies 6A and 6B revealed that negative faking related words were more arousing than positive faking related words, and that positive faking related words were more abstract than negative faking related words and neutral words. Study 7 examined whether the priming effects evident in the lexical decision tasks occurred as a result of an unintentional mood induction while faking the psychological tests. Results were equivocal in this regard. This program of research aligned the fields of psychological assessment and cognition to inform the preliminary development and validation of a new tool to detect faking. Consequently, an implicit technique to identify attempts to fake good on a psychological test has been identified, using long established and robust cognitive theories in a novel and innovative way. This approach represents a new paradigm for the detection of individuals responding strategically to psychological testing. With continuing development and validation, this technique may have immense utility in the field of psychological assessment.

Developing a model of embedding academic numeracy in university programs : a case study from nursing

This is a study of the academic numeracy of nursing students. This study develops a theoretical model for the design and delivery of university courses in academic numeracy. The following objectives are addressed: 1. To investigate nursing students' current knowledge of academic numeracy; 2. To investigate how nursing students’ knowledge and skills in academic numeracy can be enhanced using a developmental psychology framework; and 3. To utilise data derived from meeting objectives 1 and 2 to develop a theoretical model to embed academic numeracy in university programs. This study draws from Valsiner’s Human Development Theory (Valsiner, 1997, 2007). It is a quasi-experimental intervention case study (Faltis, 1997) and takes a multimethod approach using pre- and post-tests; observation notes; and semi-structured teaching sessions to document a series of microgenetic studies of student numeracy. Each microgenetic study is centered on the lived experience of students becoming more numerate. The method for this section is based on Vygotsky’s double stimulation (Valsiner, 2000a; 2007). Data collection includes interviews on students’ past experience with mathematics; their present feelings and experiences and how these present feelings and experiences are transformed. The findings from this study have provided evidence that the course developed for nursing students, underpinned by an appropriate framework, does improve academic numeracy. More specifically, students improved their content knowledge of and confidence in mathematics in areas that were directly related to their degree. The study used Valsiner’s microgenetic approach to development to trace the course as it was being taught and two students’ personal academic numeracy journeys. It highlighted particularly troublesome concepts, then outlined scaffolding and pathways used to develop understanding. This approach to academic numeracy development was summarised into a four-faceted model at the university, program, course and individual level. This model can be applied successfully to similar contexts. Thus the thesis advances both theory and practice in this under-researched and under-theorised area.

Caregiving experience and its influencing factors : rural versus urban adult-child caregivers caring for parents with dementia in China

Background: It is predicted that China will have the largest number of cases of dementia in the world by 2025 (Ferri et al., 2005). Research has demonstrated that caring for family members with dementia can be a long-term, burdensome activity resulting in physical and emotional distress and impairment (Pinquart & Sorensen, 2003b). The establishment of family caregiver supportive services in China can be considered urgent; and the knowledge of the caregiving experience and related influencing factors is necessary to inform such services. Nevertheless, in the context of rapid demographic and socioeconomic change, the impact of caregiving for rural and urban Chinese adult-child caregivers may be different, and different needs in supportive services may therefore be expected. Objectives: The aims of this research were 1) to examine the potential differences existing in the caregiving experience between rural and urban adult-child caregivers caring for parents with dementia in China; and 2) to examine the potential differences existing in the influencing factors of the caregiving experience for rural as compared with urban adult-child caregivers caring for parents with dementia in China. Based on the literature review and Kramer.s (1997) caregiver adaptation model, six concepts and their relationships of caregiving experience were studied: severity of the care receivers. dementia, caregivers. appraisal of role strain and role gain, negative and positive well-being outcomes, and health related quality of life. Furthermore, four influencing factors (i.e., filial piety, social support, resilience, and personal mastery) were studied respectively. Methods: A cross-sectional, comparative design was used to achieve the aims of the study. A questionnaire, which was designed based on the literature review and on Kramer.s (1997) caregiver adaptation model, was completed by 401 adult-child caregivers caring for their parents with dementia from the mental health outpatient departments in five hospitals in the Yunnan province, P.R. China. Structural equation modelling (SEM) was employed as the main statistical technique for data analyses. Other statistical techniques (e.g., t-tests and Chi-Square tests) were also conducted to compare the demographic characteristics and the measured variables between rural and urban groups. Results: For the first research aim, the results indicated that urban adult-child caregivers in China experienced significantly greater strain and negative well-being outcomes than their rural peers; whereas, the difference on the appraisal of role gain and positive outcomes was nonsignificant between the two groups. The results also indicated that the amounts of severity of care receivers. dementia and caregivers. health related quality of life do not have the same meanings between the two groups. Thus, the levels of these two concepts were not comparable between the rural and urban groups in this study. Moreover, the results also demonstrated that the negative direct effect of gain on negative outcomes in urban caregivers was stronger than that in rural caregivers, suggesting that the urban caregivers tended to use appraisal of role gain to protect themselves from negative well-being outcomes to a greater extent. In addition, the unexplained variance in strain in the urban group was significantly more than that in the rural group, suggesting that there were other unmeasured variables besides the severity of care receivers. dementia which would predict strain in urban caregivers compared with their rural peers. For the second research aim, the results demonstrated that rural adult-child caregivers reported a significantly higher level of filial piety and more social support than their urban counterparts, although the two groups did not significantly differ on the levels of their resilience and personal mastery. Furthermore, although the mediation effects of these four influencing factors on both positive and negative aspects remained constant across rural and urban adult-child caregivers, urban caregivers tended to be more effective in using personal mastery to protect themselves from role strain than rural caregivers, which in turn protects them more from the negative well-being outcomes than was the case with their rural peers. Conclusions: The study extends the application of Kramer.s caregiving adaptation process model (Kramer, 1997) to a sample of adult-child caregivers in China by demonstrating that both positive and negative aspects of caregiving may impact on the caregiver.s health related quality of life, suggesting that both aspects should be targeted in supportive interventions for Chinese family caregivers. Moreover, by demonstrating partial mediation effects, the study provides four influencing factors (i.e., filial piety, social support, resilience, and personal mastery) as specific targets for clinical interventions. Furthermore, the study found evidence that urban adult-child caregivers had more negative but similar positive experience compared to their rural peers, suggesting that the establishment of supportive services for urban caregivers may be more urgent at present stage in China. Additionally, since urban caregivers tended to use appraisal of role gain and personal mastery to protect themselves from negative well-being outcomes than rural caregivers to a greater extend, interventions targeting utility of gain or/and personal mastery to decrease negative outcomes might be more effective in urban caregivers than in rural caregivers. On the other hand, as cultural expectations and expression of filial piety tend to be more traditional in rural areas, interventions targeting filial piety could be more effective among rural caregivers. Last but not least, as rural adult-child caregivers have more existing natural social support than their urban counterparts, mobilising existing natural social support resources may be more beneficial for rural caregivers, whereas, formal supports (e.g., counselling services, support groups and adult day care centres) should be enhanced for urban caregivers.

Performance control of distributed generation using digital estimation of signal parameters

The Queensland University of Technology (QUT) allows the presentation of a thesis for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of seven published/submitted papers, of which one has been published, three accepted for publication and the other three are under review. This project is financially supported by an Australian Research Council (ARC) Discovery Grant with the aim of proposing strategies for the performance control of Distributed Generation (DG) system with digital estimation of power system signal parameters. Distributed Generation (DG) has been recently introduced as a new concept for the generation of power and the enhancement of conventionally produced electricity. Global warming issue calls for renewable energy resources in electricity production. Distributed generation based on solar energy (photovoltaic and solar thermal), wind, biomass, mini-hydro along with use of fuel cell and micro turbine will gain substantial momentum in the near future. Technically, DG can be a viable solution for the issue of the integration of renewable or non-conventional energy resources. Basically, DG sources can be connected to local power system through power electronic devices, i.e. inverters or ac-ac converters. The interconnection of DG systems to power system as a compensator or a power source with high quality performance is the main aim of this study. Source and load unbalance, load non-linearity, interharmonic distortion, supply voltage distortion, distortion at the point of common coupling in weak source cases, source current power factor, and synchronism of generated currents or voltages are the issues of concern. The interconnection of DG sources shall be carried out by using power electronics switching devices that inject high frequency components rather than the desired current. Also, noise and harmonic distortions can impact the performance of the control strategies. To be able to mitigate the negative effect of high frequency and harmonic as well as noise distortion to achieve satisfactory performance of DG systems, new methods of signal parameter estimation have been proposed in this thesis. These methods are based on processing the digital samples of power system signals. Thus, proposing advanced techniques for the digital estimation of signal parameters and methods for the generation of DG reference currents using the estimates provided is the targeted scope of this thesis. An introduction to this research – including a description of the research problem, the literature review and an account of the research progress linking the research papers – is presented in Chapter 1. One of the main parameters of a power system signal is its frequency. Phasor Measurement (PM) technique is one of the renowned and advanced techniques used for the estimation of power system frequency. Chapter 2 focuses on an in-depth analysis conducted on the PM technique to reveal its strengths and drawbacks. The analysis will be followed by a new technique proposed to enhance the speed of the PM technique while the input signal is free of even-order harmonics. The other techniques proposed in this thesis as the novel ones will be compared with the PM technique comprehensively studied in Chapter 2. An algorithm based on the concept of Kalman filtering is proposed in Chapter 3. The algorithm is intended to estimate signal parameters like amplitude, frequency and phase angle in the online mode. The Kalman filter is modified to operate on the output signal of a Finite Impulse Response (FIR) filter designed by a plain summation. The frequency estimation unit is independent from the Kalman filter and uses the samples refined by the FIR filter. The frequency estimated is given to the Kalman filter to be used in building the transition matrices. The initial settings for the modified Kalman filter are obtained through a trial and error exercise. Another algorithm again based on the concept of Kalman filtering is proposed in Chapter 4 for the estimation of signal parameters. The Kalman filter is also modified to operate on the output signal of the same FIR filter explained above. Nevertheless, the frequency estimation unit, unlike the one proposed in Chapter 3, is not segregated and it interacts with the Kalman filter. The frequency estimated is given to the Kalman filter and other parameters such as the amplitudes and phase angles estimated by the Kalman filter is taken to the frequency estimation unit. Chapter 5 proposes another algorithm based on the concept of Kalman filtering. This time, the state parameters are obtained through matrix arrangements where the noise level is reduced on the sample vector. The purified state vector is used to obtain a new measurement vector for a basic Kalman filter applied. The Kalman filter used has similar structure to a basic Kalman filter except the initial settings are computed through an extensive math-work with regards to the matrix arrangement utilized. Chapter 6 proposes another algorithm based on the concept of Kalman filtering similar to that of Chapter 3. However, this time the initial settings required for the better performance of the modified Kalman filter are calculated instead of being guessed by trial and error exercises. The simulations results for the parameters of signal estimated are enhanced due to the correct settings applied. Moreover, an enhanced Least Error Square (LES) technique is proposed to take on the estimation when a critical transient is detected in the input signal. In fact, some large, sudden changes in the parameters of the signal at these critical transients are not very well tracked by Kalman filtering. However, the proposed LES technique is found to be much faster in tracking these changes. Therefore, an appropriate combination of the LES and modified Kalman filtering is proposed in Chapter 6. Also, this time the ability of the proposed algorithm is verified on the real data obtained from a prototype test object. Chapter 7 proposes the other algorithm based on the concept of Kalman filtering similar to those of Chapter 3 and 6. However, this time an optimal digital filter is designed instead of the simple summation FIR filter. New initial settings for the modified Kalman filter are calculated based on the coefficients of the digital filter applied. Also, the ability of the proposed algorithm is verified on the real data obtained from a prototype test object. Chapter 8 uses the estimation algorithm proposed in Chapter 7 for the interconnection scheme of a DG to power network. Robust estimates of the signal amplitudes and phase angles obtained by the estimation approach are used in the reference generation of the compensation scheme. Several simulation tests provided in this chapter show that the proposed scheme can very well handle the source and load unbalance, load non-linearity, interharmonic distortion, supply voltage distortion, and synchronism of generated currents or voltages. The purposed compensation scheme also prevents distortion in voltage at the point of common coupling in weak source cases, balances the source currents, and makes the supply side power factor a desired value.

Controls on iron in soils and soil waters of a forested, coastal catchment in subtropical Australia

Soluble organic matter derived from exotic Pinus vegetation forms stronger complexes with iron (Fe) than the soluble organic matter derived from most native Australian species. This has lead to concern about the environmental impacts related to the establishment of extensive exotic Pinus plantations in coastal southeast Queensland, Australia. It has been suggested that the Pinus plantations may enhance the solubility of Fe in soils by increasing the amount of organically complexed Fe. While this remains inconclusive, the environmental impacts of an increased flux of dissolved, organically complexed Fe from soils to the fluvial system and then to sensitive coastal ecosystems are potentially damaging. Previous work investigated a small number of samples, was largely laboratory based and had limited application to field conditions. These assessments lacked field-based studies, including the comparison of the soil water chemistry of sites associated with Pinus vegetation and undisturbed native vegetation. In addition, the main controls on the distribution and mobilisation of Fe in soils of this subtropical coastal region have not been determined. This information is required in order to better understand the relative significance of any Pinus enhanced solubility of Fe. The main aim of this thesis is to determine the controls on Fe distribution and mobilisation in soils and soil waters of a representative coastal catchment in southeast Queensland (Poona Creek catchment, Fraser Coast) and to test the effect of Pinus vegetation on the solubility and speciation of Fe. The thesis is structured around three individual papers. The first paper identifies the main processes responsible for the distribution and mobilisation of labile Fe in the study area and takes a catchment scale approach. Physicochemical attributes of 120 soil samples distributed throughout the catchment are analysed, and a new multivariate data analysis approach (Kohonen’s self organising maps) is used to identify the conditions associated with high labile Fe. The second paper establishes whether Fe nodules play a major role as an iron source in the catchment, by determining the genetic mechanism responsible for their formation. The nodules are a major pool of Fe in much of the region and previous studies have implied that they may be involved in redox-controlled mobilisation and redistribution of Fe. This is achieved by combining a detailed study of a ferric soil profile (morphology, mineralogy and micromorphology) with the distribution of Fe nodules on a catchment scale. The third component of the thesis tests whether the concentration and speciation of Fe in soil solutions from Pinus plantations differs significantly from native vegetation soil solutions. Microlysimeters are employed to collect unaltered, in situ soil water samples. The redox speciation of Fe is determined spectrophotometrically and the interaction between Fe and dissolved organic matter (DOM) is modelled with the Stockholm Humic Model. The thesis provides a better understanding of the controls on the distribution, concentration and speciation of Fe in the soils and soil waters of southeast Queensland. Reductive dissolution is the main mechanism by which mobilisation of Fe occurs in the study area. Labile Fe concentrations are low overall, particularly in the sandy soils of the coastal plain. However, high labile Fe is common in seasonally waterlogged and clay-rich soils which are exposed to fluctuating redox conditions and in organic-rich soils adjacent to streams. Clay-rich soils are most common in the upper parts of the catchment. Fe nodules were shown to have a negligible role in the redistribution of dissolved iron in the catchment. They are formed by the erosion, colluvial transport and chemical weathering of iron-rich sandstones. The ferric horizons, in which nodules are commonly concentrated, subsequently form through differential biological mixing of the soil. Whereas dissolution/ reprecipitation of the Fe cements is an important component of nodule formation, mobilised Fe reprecipitates locally. Dissolved Fe in the soil waters is almost entirely in the ferrous form. Vegetation type does not affect the concentration and speciation of Fe in soil waters, although Pinus DOM has greater acidic functional group site densities than DOM from native vegetation. Iron concentrations are highest in the high DOM soil waters collected from sandy podosols, where they are controlled by redox potential. Iron concentrations are low in soil solutions from clay and iron oxide rich soils, in spite of similar redox potentials. This is related to stronger sorption to the reactive clay and iron oxide mineral surfaces in these soils, which reduces the amount of DOM available for microbial metabolisation and reductive dissolution of Fe. Modelling suggests that Pinus DOM can significantly increase the amount of truly dissolved ferric iron remaining in solution in oxidising conditions. Thus, inputs of ferrous iron together with Pinus DOM to surface waters may reduce precipitation of hydrous ferric oxides and increase the flux of dissolved iron out of the catchment. Such inputs are most likely from the lower catchment, where podosols planted with Pinus are most widely distributed. Significant outcomes other than the main aims were also achieved. It is shown that mobilisation of Fe in podosols can occur as dissolved Fe(II) rather than as Fe(III)-organic complexes. This has implications for the large body of work which assumes that Fe(II) plays a minor role. Also, the first paper demonstrates that a data analysis approach based on Kohonen’s self organising maps can facilitate the interpretation of complex datasets and can help identify geochemical processes operating on a catchment scale.

Formation mechanisms of secondary organic aerosols in relation to laser printer emissions

Due to their large surface area, complex chemical composition and high alveolar deposition rate, ultrafine particles (UFPs) (< 0.1 ìm) pose a significant risk to human health and their toxicological effects have been acknowledged by the World Health Organisation. Since people spend most of their time indoors, there is a growing concern about the UFPs present in some indoor environments. Recent studies have shown that office machines, in particular laser printers, are a significant indoor source of UFPs. The majority of printer-generated UFPs are organic carbon and it is unlikely that these particles are emitted directly from the printer or its supplies (such as paper and toner powder). Thus, it was hypothesised that these UFPs are secondary organic aerosols (SOA). Considering the widespread use of printers and human exposure to these particles, understanding the processes involved in particle formation is of critical importance. However, few studies have investigated the nature (e.g. volatility, hygroscopicity, composition, size distribution and mixing state) and formation mechanisms of these particles. In order to address this gap in scientific knowledge, a comprehensive study including state-of-art instrumental methods was conducted to characterise the real-time emissions from modern commercial laser printers, including particles, volatile organic compounds (VOCs) and ozone (O3). The morphology, elemental composition, volatility and hygroscopicity of generated particles were also examined. The large set of experimental results was analysed and interpreted to provide insight into: (1) Emissions profiles of laser printers: The results showed that UFPs dominated the number concentrations of generated particles, with a quasi unimodal size distribution observed for all tests. These particles were volatile, non-hygroscopic and mixed both externally and internally. Particle microanalysis indicated that semi-volatile organic compounds occupied the dominant fraction of these particles, with only trace quantities of particles containing Ca and Fe. Furthermore, almost all laser printers tested in this study emitted measurable concentrations of VOCs and O3. A positive correlation between submicron particles and O3 concentrations, as well as a contrasting negative correlation between submicron particles and total VOC concentrations were observed during printing for all tests. These results proved that UFPs generated from laser printers are mainly SOAs. (2) Sources and precursors of generated particles: In order to identify the possible particle sources, particle formation potentials of both the printer components (e.g. fuser roller and lubricant oil) and supplies (e.g. paper and toner powder) were investigated using furnace tests. The VOCs emitted during the experiments were sampled and identified to provide information about particle precursors. The results suggested that all of the tested materials had the potential to generate particles upon heating. Nine unsaturated VOCs were identified from the emissions produced by paper and toner, which may contribute to the formation of UFPs through oxidation reactions with ozone. (3) Factors influencing the particle emission: The factors influencing particle emissions were also investigated by comparing two popular laser printers, one showing particle emissions three orders of magnitude higher than the other. The effects of toner coverage, printing history, type of paper and toner, and working temperature of the fuser roller on particle number emissions were examined. The results showed that the temperature of the fuser roller was a key factor driving the emission of particles. Based on the results for 30 different types of laser printers, a systematic positive correlation was observed between temperature and particle number emissions for printers that used the same heating technology and had a similar structure and fuser material. It was also found that temperature fluctuations were associated with intense bursts of particles and therefore, they may have impact on the particle emissions. Furthermore, the results indicated that the type of paper and toner powder contributed to particle emissions, while no apparent relationship was observed between toner coverage and levels of submicron particles. (4) Mechanisms of SOA formation, growth and ageing: The overall hypothesis that UFPs are formed by reactions with the VOCs and O3 emitted from laser printers was examined. The results proved this hypothesis and suggested that O3 may also play a role in particle ageing. In addition, knowledge about the mixing state of generated particles was utilised to explore the detailed processes of particle formation for different printing scenarios, including warm-up, normal printing, and printing without toner. The results indicated that polymerisation may have occurred on the surface of the generated particles to produce thermoplastic polymers, which may account for the expandable characteristics of some particles. Furthermore, toner and other particle residues on the idling belt from previous print jobs were a very clear contributing factor in the formation of laser printer-emitted particles. In summary, this study not only improves scientific understanding of the nature of printer-generated particles, but also provides significant insight into the formation and ageing mechanisms of SOAs in the indoor environment. The outcomes will also be beneficial to governments, industry and individuals.

Safety enhancement of operator protection systems on self-propelled mining equipment

In the long term, with development of skill, knowledge, exposure and confidence within the engineering profession, rigorous analysis techniques have the potential to become a reliable and far more comprehensive method for design and verification of the structural adequacy of OPS, write Nimal J Perera, David P Thambiratnam and Brian Clark. This paper explores the potential to enhance operator safety of self-propelled mechanical plant subjected to roll over and impact of falling objects using the non-linear and dynamic response simulation capabilities of analytical processes to supplement quasi-static testing methods prescribed in International and Australian Codes of Practice for bolt on Operator Protection Systems (OPS) that are post fitted. The paper is based on research work carried out by the authors at the Queensland University of Technology (QUT) over a period of three years by instrumentation of prototype tests, scale model tests in the laboratory and rigorous analysis using validated Finite Element (FE) Models. The FE codes used were ABAQUS for implicit analysis and LSDYNA for explicit analysis. The rigorous analysis and dynamic simulation technique described in the paper can be used to investigate the structural response due to accident scenarios such as multiple roll over, impact of multiple objects and combinations of such events and thereby enhance the safety and performance of Roll Over and Falling Object Protection Systems (ROPS and FOPS). The analytical techniques are based on sound engineering principles and well established practice for investigation of dynamic impact on all self propelled vehicles. They are used for many other similar applications where experimental techniques are not feasible.

Section moment capacity tests of LiteSteel Beams

The LiteSteel Beam (LSB) is a new cold-formed hollow flange channel section developed by OneSteel Australian Tube Mills using their patented dual electric resistance welding and automated continuous roll-forming process. It has a unique geometry consisting of torsionally rigid rectangular hollow flanges and a relatively slender web. In addition to this unique geometry, the LSB sections also have unique characteristics relating to their stress-strain curves, residual stresses, initial geometric imperfections and hollow flanges that are not encountered in conventional hot-rolled and cold-formed steel channel sections. An experimental study including 20 section moment capacity tests was therefore conducted to investigate the behaviour and strength of LSB flexural members. The presence of inelastic reserve bending capacity in these beams was investigated in detail although the current design rules generally limit the section moment capacities of cold-formed steel members to their first yield moments. The ultimate moment capacities from the tests were compared with the section moment capacities predicted by the current cold-formed and hot-rolled steel design standards. It was found that compact and non-compact LSB sections have greater moment capacities than their first yield moments. The current cold-formed steel design standards were found to be conservative in predicting the section moment capacities of compact and non-compact LSB sections while the hot-rolled steel design standards were able to better predict them. This paper has shown that suitable modifications are needed to the current design rules to allow the inclusion of available inelastic bending capacities of LSBs in design.

Time limitations in NAPLAN numeracy tests

The article discusses evidence that time prevented many students from showing what they could do in the 2010 Year 7 and 9 NAPLAN numeracy tests. In addition to analysing the available data, the article discusses some NAPLAN numeracy questions that contribute to this problem. It is suggested that schools should investigate whether time limitation is a problem for their own students. The article discusses the implications of these findings for teachers preparing students for NAPLAN tests and for the developers of the tests.

Non-compositional concepts and quantum tests

Compositionality is a frequently made assumption in linguistics, and yet many human subjects reveal highly non-compositional word associations when confronted with novel concept combinations. This article will show how a non-compositional account of concept combinations can be supplied by modelling them as interacting quantum systems.

Tests and Models of Non-compositional Concepts

The question of under what conditions conceptual representation is compositional remains debatable within cognitive science. This paper proposes a well developed mathematical apparatus for a probabilistic representation of concepts, drawing upon methods developed in quantum theory to propose a formal test that can determine whether a specific conceptual combination is compositional, or not. This test examines a joint probability distribution modeling the combination, asking whether or not it is factorizable. Empirical studies indicate that some combinations should be considered non-compositionally.

Wing shape as a potential discriminator of morphologically similar pest taxa within the Bactrocera dorsalis species complex (Diptera: Tephritidae)

Four morphologically cryptic species of the Bactrocera dorsalis fruit fly complex (B. dorsalis s.s., B. papayae, B. carambolae and B. philippinensis) are serious agricultural pests. As they are difficult to diagnose using traditional taxonomic techniques, we examined the potential for geometric morphometric analysis of wing size and shape to discriminate between them. Fifteen wing landmarks generated size and shape data for 245 specimens for subsequent comparisons among three geographically distinct samples of each species. Intraspecific wing size was significantly different within samples of B. carambolae and B. dorsalis s.s. but not within samples of B. papayae or B. philippinensis. Although B. papayae had the smallest wings (average centroid size=6.002 mm±0.061 SE) and B. dorsalis s.s. the largest (6.349 mm±0.066 SE), interspecific wing size comparisons were generally non-informative and incapable of discriminating species. Contrary to the wing size data, canonical variate analysis based on wing shape data discriminated all species with a relatively high degree of accuracy; individuals were correctly reassigned to their respective species on average 93.27% of the time. A single sample group of B. carambolae from locality 'TN Malaysia' was the only sample to be considerably different from its conspecific groups with regards to both wing size and wing shape. This sample was subsequently deemed to have been originally misidentified and likely represents an undescribed species. We demonstrate that geometric morphometric techniques analysing wing shape represent a promising approach for discriminating between morphologically cryptic taxa of the B. dorsalis species complex.