Investigation of the airborne submicrometer particles emitted by dredging vessels using a plume capture method

This paper presents a method for investigating ship emissions, the plume capture and analysis system (PCAS), and its application in measuring airborne pollutant emission factors (EFs) and particle size distributions. The current investigation was conducted in situ, aboard two dredgers (Amity: a cutter suction dredger and Brisbane: a hopper suction dredger) but the PCAS is also capable of performing such measurements remotely at a distant point within the plume. EFs were measured relative to the fuel consumption using the fuel combustion derived plume CO2. All plume measurements were corrected by subtracting background concentrations sampled regularly from upwind of the stacks. Each measurement typically took 6 minutes to complete and during one day, 40 to 50 measurements were possible. The relationship between the EFs and plume sample dilution was examined to determine the plume dilution range over which the technique could deliver consistent results when measuring EFs for particle number (PN), NOx, SO2, and PM2.5 within a targeted dilution factor range of 50-1000 suitable for remote sampling. The EFs for NOx, SO2, and PM2.5 were found to be independent of dilution, for dilution factors within that range. The EF measurement for PN was corrected for coagulation losses by applying a time dependant particle loss correction to the particle number concentration data. For the Amity, the EF ranges were PN: 2.2 - 9.6 × 1015 (kg-fuel)-1; NOx: 35-72 g(NO2).(kg-fuel)-1, SO2 0.6 - 1.1 g(SO2).(kg-fuel)-1and PM2.5: 0.7 – 6.1 g(PM2.5).(kg-fuel)-1. For the Brisbane they were PN: 1.0 – 1.5 x 1016 (kg-fuel)-1, NOx: 3.4 – 8.0 g(NO2).(kg-fuel)-1, SO2: 1.3 – 1.7 g(SO2).(kg-fuel)-1 and PM2.5: 1.2 – 5.6 g(PM2.5).(kg-fuel)-1. The results are discussed in terms of the operating conditions of the vessels’ engines. Particle number emission factors as a function of size as well as the count median diameter (CMD), and geometric standard deviation of the size distributions are provided. The size distributions were found to be consistently uni-modal in the range below 500 nm, and this mode was within the accumulation mode range for both vessels. The representative CMDs for the various activities performed by the dredgers ranged from 94-131 nm in the case of the Amity, and 58-80 nm for the Brisbane. A strong inverse relationship between CMD and EF(PN) was observed.

Growing profitable or growing from profits : putting the horse in front of the cart?

Top lists of and praise for the economy's fastest growing firms abound in business media around the world. Similarly, in academic research there has been a tendency to equate firm growth with business success. This tendency appears to be particularly pronounced in-but not confined to­ entrepreneurship research. In this study we critically examine this tendency to portray firm growth as more or less universally favorable. While several theories suggest that growth drives profitability we first show that the available empirical evidence does not support the existence of a general, positive relation­ ship between growth and profitability. Using the theoretical lens of the Resource-Based View (RBV) we then argue that sound growth usually starts with achieving sufficient levels of profitability. In summary, our theoretical argument is as follows: In a population of SMEs, superior profitability is likely to be indicative of having built a resource-based competitive advantage. Building such a valuable and hard to-copy advantage may at first constrain growth. However, the underlying advantage itself and the financial resources generated through high profitability make it possible for firms in this situation to now achieve sound and sustainable growth - which may require building a series of temporary advantages- without having to sacrifice profitability. By contrast, when firms strive for high growth starting from low profitability, the latter often indicates lack of competitive advantage. Therefore growth must be achieved in head-to-head competition with equally attractive alternatives, leading to profitability deterioration rather than improvement. In addition, these low profitability firms are unlikely to be able to finance strategies toward building valuable and difficult-to-imitate advantages while growing.

Revitalising the Australian Shipping Industry through Tax Reform: Alchemy or Piracy?

The Australian Federal Government has recently passed reforms to the shipping industry. These reforms are aimed at removing barriers to investment in Australian shipping, fostering global competitiveness and securing a stable maritime skills base. The shipping reform package adopts a two pronged approach designed to achieve its stated goals by providing both a ‘stick’ and ‘carrot’ to industry participants. First, the ‘stick’ is delivered via the provision of tighter regulation of coastal trading operations through a new licencing system, along with the introduction of a civil penalty regime and an increase in existing penalties. Second, the ‘carrot’ is delivered via taxation incentives available to vessels registered in Australia where the registrant meets certain specified criteria. These incentives, introduced through amendments to the Income Tax Assessment Act 1997 and the Income Tax Assessment Act 1936 and contained in the Tax Laws Amendment (Shipping Reform) Act 2012, provide five key tax incentives to the shipping industry. From 1 July 2012, amendments give effect to an income tax exemption for qualifying ship operators, accelerated depreciation of vessels, roll-over relief from income tax on the sale of a vessel, an employer refundable tax offset, and an exemption from royalty withholding tax for payments made for the lease of certain shipping vessels.

IMO mandatory energy efficiency measures for international shipping : the first mandatory global greenhouse gas reduction instrument for an international industry

Bunker fuels used in the aviation and maritime sectors are responsible for nearly 10% of global greenhouse gas emissions.1 According to a scientific survey: ‘[s]hipping is estimated to have emitted 1,046 million tonnes of CO2 in 2007, which corresponds to 3.3% of the global emissions during 2007. International shipping is estimated to have emitted 870 million tonnes, or about 2.7% of the global emissions of CO2 in 2007’. The study also predicted that ‘by 2050, in the absence of policies, ship emissions may grow by 150% to 250% (compared to the emissions in 2007) as a result of the growth in shipping.’

Environmental pollution from shipbreaking industry : international law and national legal response

The international legal regime on shipbreaking is in its formative years. At the international level, the shipbreaking industry is partially governed by the Basel Convention on the Control of Transboundary Movements of Hazardous Wastes and their Disposal. However, how far this convention will be applicable for all aspects of transboundary movement of end-of-life ships is still, at least in the view of some scholars, a debatable issue. Against this backdrop, the International Maritime Organisation (IMO) has adopted a new, legally binding convention for shipbreaking. There is a rising voice from the developing countries that the convention is likely to impose more obligations on recycling facilities in the developing countries than on shipowners from rich nations. This may be identified as a clear derogation from the globally recognized international environmental law principle of common but differentiated treatment. This article will examine in detail major international conventions regulating transboundary movement and environmentally sound disposal of obsolete ships, as well as the corresponding laws of Bangladesh for implementing these conventions in the domestic arena. Moreover this article will examine in detail the recently adopted IMO Ship Recycling Convention.

Water and chloride ion penetration resistance of highstrength ultra lightweight cement composite

Durability is a significant issue to focus on for newly developed structural lightweight cement composite (ULCC). This paper presents an experimental study to evaluate the resistance of ULCC to water and chloride ion penetration. Chloride penetrability and sorptivity were evaluated for ULCC (unit weight about 1450 kg/m3) and compared with those of a normal weight concrete (NWC), a lightweight aggregate concrete (LWC), and an ultra lightweight composite with proprietary cementitious binder (DB) (unit weight about 1450 kg/m3) at similar compressive strength of about 60 MPa. Rapid chloride penetrability test, rapid migration test, water absorption (sorptivity) test, and water permeability test were conducted on these mixtures. Results indicate that ULCC and DB had comparable performance. Compared with control LWC and NWC at similar strength level, the ULCC and DB mixtures had higher resistance to chloride ion penetration, lower water absorption and virtually impermeable to water penetration.

High-strength high-performance lightweight concrete : a review (Invited)

In the last two decades, there are developments that lead to greater understanding on how and why lightweight concretes (LWC) may achieve similar or higher performance than their normal weight counterparts. The present paper reviews some of these aspects beginning with basic properties such as unit weight, compressive strength and specific strength (strength/ unit weight). Stability and workability of LWC is discussed from rheological perspective. The volumetric stability of LWC in terms of shrinkage and creep are presented with some recent published data. Transport properties of the LWC in terms of sorptivity, water permeability and resistance to chloride-ion penetration are reviewed in comparison with normal weight concrete. Fire resistance of LWC and some current measures used to improve the resistance are discussed. With continual research and development, the performance of LWC is being enhanced to provide new opportunities for practical applications.

Development of lightweight aggregate concrete with high resistance to water and chloride-ion penetration

This paper presents an experimental study to evaluate the effect of coarse and fine LWA in concrete on its water absorption and permeability, and resistance to chloride-ion penetration. In additions, LWC with lower unit weight of about 1300 kg/m3 but high resistance to water and chloride-ion penetration was developed and evaluated. The results indicate that the incorporation of coarse LWA in concrete increases water sorptivity and permeability slightly compared to NWC of similar w/c. The resistance of the sand-LWC to chloride-ion penetration depends on porosity of the coarse LWA. Fine LWA has more influence on the transport proper-ties of concrete than coarse LWA. Use of lightweight crushed sand <1.18 mm reduced the resistance of the LWC to water and chloride-ion penetration to some extent. With low w/cm and silica fume, low unit weight LWC (~1300 kg/m3) was produced with higher resistance to water and chloride ion penetration compared with concretes of higher unit weights.

Legal regulation of 'decent work' : evidence from two big industries in Bangladesh

In most developing countries, the overall quality of the livelihood of labourers, work place environment and implementation of labour rights do not progress at the same rate as their industrial development. To address this situation, the ILO has initiated the concept of 'decent work' to assist regulators articulate labour-related social policy goals. Against this backdrop, this article assesses the Bangladesh Labour Law 2006 by reference to the four social principles developed by the ILO for ensuring 'decent work'. It explains the impact of the absence of these principles in this Law on the labour administration in the ready-made garment and ship-breaking industries. It finds that an appropriate legislative framework needs to be based on the principles of 'decent work' to establish a solid platform for a sound labour regulation in Bangladesh.

Newstead House : the social history, culture and architecture of a bygone era

Historic house museums form a significant component of the built heritage and social history of a country. They vary from the elaborate mansions of the wealthy to modest dwellings of the working class. Regardless of the original owner's status in society these house museums are vital to an understanding of architecture, culture and society from a bygone era. The Newstead House, the oldest surviving residence, in Brisbane, is the first house to be designated a 'Historic House Museum' in Queensland. It is a representative example of a house that demonstrates the British colonial heritage of 19th century Australia. Originally a modest cottage, on 34 acres of land, the Newstead house was built by a Scottish migrant. The ownership of the house and land changed many times, during the period from 1847 to 1939. During this period a series of prominent residents of Brisbane either owned or rented this residence. They included, an officer of the Royal Navy, politicians, magistrates, merchant ship owners, and a Consul General of the United States of America. As a result, the house went through a series of renovations and extensions to accommodate the needs of its owners and their position in society. This paper aims to investigate the significance of historic museum houses in educating the community on aspects of social history, culture and architecture of 19th century Australia. It will focus on the heritage listed Newstead House as a case study to demonstrate the significance of the house as an artefact and an educational tool.

Displacement motion prediction of a landing deck for recovery operations of rotary UAVs

This paper proposes a practical prediction procedure for vertical displacement of a Rotarywing Unmanned Aerial Vehicle (RUAV) landing deck in the presence of stochastic sea state disturbances. A proper time series model tending to capture characteristics of the dynamic relationship between an observer and a landing deck is constructed, with model orders determined by a novel principle based on Bayes Information Criterion (BIC) and coefficients identified using the Forgetting Factor Recursive Least Square (FFRLS) method. In addition, a fast-converging online multi-step predictor is developed, which can be implemented more rapidly than the Auto-Regressive (AR) predictor as it requires less memory allocations when updating coefficients. Simulation results demonstrate that the proposed prediction approach exhibits satisfactory prediction performance, making it suitable for integration into ship-helicopter approach and landing guidance systems in consideration of computational capacity of the flight computer.

A nonlinear position controller for maritime operations of Rotary-wing UAVs

This paper presents a disturbance attenuation controller for horizontal position stabilization for hover and automatic landings of a Rotary-wing Unmanned Aerial Vehicle (RUAV) operating in rough seas. Based on a helicopter model representing aerodynamics during the landing phase, a nonlinear state feedback H-infinity controller is designed to achieve rapid horizontal position tracking in a gusty environment. The resultant control variables are further treated in consideration of practical constraints (flapping dynamics, servo dynamics and time lag effect) for implementation purpose. The high-fidelity closed-loop simulation using parameters of the Vario helicopter verifies performance of the proposed position controller. It not only increases the disturbance attenuation capability of the RUAV, but also enables rapid position response when gusts occur. Comparative studies show that the H-infinity controller exhibits great performance improvement and can be applied to ship/RUAV landing systems.

Non-linear position control for hover and automatic landing of unmanned aerial vehicles

This study presents a disturbance attenuation controller for horizontal position stabilisation for hover and automatic landings of a rotary-wing unmanned aerial vehicle (RUAV) operating close to the landing deck in rough seas. Based on a helicopter model representing aerodynamics during the landing phase, a non-linear state feedback H∞ controller is designed to achieve rapid horizontal position tracking in a gusty environment. Practical constraints including flapping dynamics, servo dynamics and time lag effect are considered. A high-fidelity closed-loop simulation using parameters of the Vario XLC gas-turbine helicopter verifies performance of the proposed horizontal position controller. The proposed controller not only increases the disturbance attenuation capability of the RUAV, but also enables rapid position response when gusts occur. Comparative studies show that the H∞ controller exhibits performance improvement and can be applied to ship/RUAV landing systems.

Monotonous trend estimation of deck displacement for automatic landing of rotorcraft UAVs

This paper presents a novel and practical procedure for estimating the mean deck height to assist in automatic landing operations of a Rotorcraft Unmanned Aerial Vehicle (RUAV) in harsh sea environments. A modified Prony Analysis (PA) procedure is outlined to deal with real-time observations of deck displacement, which involves developing an appropriate dynamic model to approach real deck motion with parameters identified through implementing the Forgetting Factor Recursive Least Square (FFRLS) method. The model order is specified using a proper order-selection criterion based on minimizing the summation of accumulated estimation errors. In addition, a feasible threshold criterion is proposed to separate the dominant components of deck displacement, which results in an accurate instantaneous estimation of the mean deck position. Simulation results demonstrate that the proposed recursive procedure exhibits satisfactory estimation performance when applied to real-time deck displacement measurements, making it well suited for integration into ship-RUAV approach and landing guidance systems.

Climate change and IMO technical and operational measures for reduction of emissions of greenhouse gas from ships

According to a study conducted by the International Maritime organisation (IMO) shipping sector is responsible for 3.3% of the global Greenhouse Gas (GHG) emissions. The 1997 Kyoto Protocol calls upon states to pursue limitation or reduction of emissions of GHG from marine bunker fuels working through the IMO. In 2011, 14 years after the adoption of the Kyoto Protocol, the Marine Environment Protection Committee (MEPC) of the IMO has adopted mandatory energy efficiency measures for international shipping which can be treated as the first ever mandatory global GHG reduction instrument for an international industry. The MEPC approved an amendment of Annex VI of the 1973 International Convention for the Prevention of Pollution from Ships (MARPOL 73/78) to introduce a mandatory Energy Efficiency Design Index (EEDI) for new ships and the Ship Energy Efficiency Management Plan (SEEMP) for all ships. Considering the growth projections of human population and world trade the technical and operational measures may not be able to reduce the amount of GHG emissions from international shipping in a satisfactory level. Therefore, the IMO is considering to introduce market-based mechanisms that may serve two purposes including providing a fiscal incentive for the maritime industry to invest in more energy efficient manner and off-setting of growing ship emissions. Some leading developing countries already voiced their serious reservations on the newly adopted IMO regulations stating that by imposing the same obligation on all countries, irrespective of their economic status, this amendment has rejected the Principle of Common but Differentiated Responsibility (the CBDR Principle), which has always been the cornerstone of international climate change law discourses. They also claimed that negotiation for a market based mechanism should not be continued without a clear commitment from the developed counters for promotion of technical co-operation and transfer of technology relating to the improvement of energy efficiency of ships. Against this backdrop, this article explores the challenges for the developing counters in the implementation of already adopted technical and operational measures.