Radiative and total heat transfer measurements to a Titan Explorer model

Radiative and total heat transfer at the flow stagnation point of a 1:40.8 binary scaled model of the Titan Explorer vehicle were measured in the X3 expansion tube. Results from the current study illustrated that with the addition of CH4 into a N2 test gas radiative heat transfer could be detected. For a test gas of 5% CH4 and 95% N2, simulating an atmospheric model for Titanic aerocapture, approximately 4% of the experimentally measured total stagnation point heat transfer was found to be due to radiation. This was in comparison to < 1% measured for a test gas of pure nitrogen. When scaled to the flight vehicle, experimental results indicate a 64% contribution of radiation (test gas 5% CH4/95% N2). Previous numerical results however have predicted this contribution to be between 80-92%. Thus, experimental results from the current study suggest that numerical analyses are over-predicting the radiative heat transfer on the flight vehicle.

Heat transfer measurements on the first experimental layer of the FIRE II reentry vehicle in expansion tubes

The present study focused on simulating a trajectory point towards the end of the first experimental heatshield of the FIRE II vehicle, at a total flight time of 1639.53s. Scale replicas were sized according to binary scaling and instrumented with thermocouples for testing in the X1 expansion tube, located at The University of Queensland. Correlation of flight to experimental data was achieved through the separation, and independent treatment of the heat modes. Preliminary investigation indicates that the absolute value of radiant surface flux is conserved between two binary scaled models, whereas convective heat transfer increases with the length scale. This difference in the scaling techniques result in the overall contribution of radiative heat transfer diminishing to less than 1% in expansion tubes from a flight value of approximately 9-17%. From empirical correlation's it has been shown that the St √Re number decreases, under special circumstances, in expansion tubes by the percentage radiation present on the flight vehicle. Results obtained in this study give a strong indication that the relative radiative heat transfer contribution in the expansion tube tests is less than that in flight, supporting the analysis that the absolute value remains constant with binary scaling.

Residual stresses in rail-ends from the in-service insulated rail joints using neutron diffraction

Insulated rail joints (IRJs) are an integral part of the rail track signaling system and pose significant maintenance and replacement costs due to their low and fluctuating service lives. Failure occurs mainly in rail head region, bolt- holes of fishplates and web-holes of the rails. Propagation of cracks is influenced by the evolution of internal residual stresses in rails during rail manufacturing (hot-rolling, roller-straightening, and head-hardening process), and during service, particularly in heavy rail haul freight systems where loads are high. In this investigation, rail head accumulated residual stresses were analysed using neutron diffraction at the Australian Nuclear Science and Technology Organisation (ANSTO). Two ex-service two head-hardened rail joints damaged under different loading were examined and results were compared with those obtained from an unused rail joint reference sample in order to differentiate the stresses developed during rail manufacturing and stresses accumulated during rail service. Neutron diffraction analyses were carried out on the samples in longitudinal, transverse and vertical directions, and on 5mm thick sliceed samples cut by Electric Discharge Machining (EDM). For the rail joints from the service line, irrespective of loading conditions and in-service times, results revealed similar depth profiles of stress distribution. Evolution of residual stress fields in rails due to service was also accompanied by evidence of larger material flow based on reflected light and scanning electron microscopy studies. Stress evolution in the vicinity of rail ends was characterised by a compressive layer, approximately 5 mm deep, and a tension zone located approximately 5- 15mm below the surfaces. A significant variation of d0 with depth near the top surface was detected and was attributed to decarburization in the top layer induced by cold work. Stress distributions observed in longitudinal slices of the two different deformed rail samples were found to be similar. For the undeformed rail, the stress distributions obtained could be attributed to variations associated with thermo-mechanical history of the rail.

Design Minds Refresh Toolkit

The Design Minds Refresh Toolkit was one of six K7-12 secondary school design toolkits commissioned by the State Library of Queensland (SLQ) Asia Pacific Design Library (APDL), to facilitate the delivery of the Stage 1 launch of its Design Minds online platform (www.designminds.org.au) partnership initiative with Queensland Government Arts Queensland and the Smithsonian Cooper-Hewitt National Design Museum, on June 29, 2012. Design Minds toolkits are practical guides, underpinned by a combination of one to three of the Design Minds model phases of ‘Inquire’, ‘Ideate’ and ‘Implement’ (supported by at each stage with structured reflection), to enhance existing school curriculum and empower students with real life design exercises, within the classroom environment. Toolkits directly identify links to Naplan, National Curriculum, C2C and Professional Standards benchmarks, as well as the student capabilities of successful and creative 21st century citizens they seek to engender through design thinking. Inspired by ideas from a design project for second year Interior Design students at QUT School of Design, this toolkit explores, through five distinct exercises, different design tools and ways to approach the future design of environments (bathrooms) to facilitate the daily washing ritual, while addressing diverse and changing social, cultural, technological and environmental challenges. The Design Minds Refresh Toolkit particularly aims to promote ‘Lateral Thinking’ attitudes and empathy as an approach to create unusual and sustainable solutions to future problems that may affect our daily behavioural routines, and the spaces that facilitate them. More generally, it aims to facilitate awareness in young people, of the role of design in society and the value of design thinking skills in generating strategies to solve basic to complex systemic challenges, as well as to inspire post-secondary pathways and idea generation for education. The toolkit encourages students and teachers to develop sketching, making, communication, presentation and collaboration skills to improve their design process, as well as explore further inquiry (background research) to enhance the ideation exercises. Exercise 1 focuses on the ‘Inquire’ and ‘Ideate’ phases, Exercise 2 and 3 build on ideation skills, and Exercise 4 and 5 concentrate on the ‘Implement’ phase. Depending on the intensity of the focus, the unit of work could be developed over a 4-5 week program (approximately 10-12 x 60 minute lessons/workshops) or as smaller workshops treated as discrete learning experiences. The toolkit is available for public download from http://designminds.org.au/refresh/ on the Design Minds website. Exercise 2 (Other People’s Shoes) and Exercise 3 (The Future Bathroom) of the toolkit were used as content for the inaugural Design Minds Professional Development Workshop on June 28, 2012 to pre-launch the website to Queensland teachers.

Design Minds The Big Picture Toolkit

The Design Minds The Big Picture Toolkit was one of six K7-12 secondary school design toolkits commissioned by the State Library of Queensland (SLQ) Asia Pacific Design Library (APDL), to facilitate the delivery of the Stage 1 launch of its Design Minds online platform (www.designminds.org.au) partnership initiative with Queensland Government Arts Queensland and the Smithsonian Cooper-Hewitt National Design Museum, on June 29, 2012. Design Minds toolkits are practical guides, underpinned by a combination of one to three of the Design Minds model phases of ‘Inquire’, ‘Ideate’ and ‘Implement’ (supported by at each stage with structured reflection), to enhance existing school curriculum and empower students with real life design exercises, within the classroom environment. Toolkits directly identify links to Naplan, National Curriculum, C2C and Professional Standards benchmarks, as well as the student capabilities of successful and creative 21st century citizens they seek to engender through design thinking. Inspired by the Unlimited: Designing for the Asia Pacific Generation Workshop 2010 (http://eprints.qut.edu.au/47762/), this toolkit explores, through three distinct exercises, ‘design for the other 90%’, addressing tools and approaches to diverse and changing social, cultural, technological and environmental challenges. The Design Minds The Big Picture Toolkit challenges students to be active agents for change and to think creatively and optimistically about solutions to future global issues that deliver social, economic and environmental benefits. More generally, it aims to facilitate awareness in young people, of the role of design in society and the value of design thinking skills in generating strategies to solve basic to complex systemic challenges, as well as to inspire post-secondary pathways and idea generation for education. The toolkit encourages students and teachers to develop sketching, making, communication, presentation and collaboration skills to improve their design process, as well as explore further inquiry (background research) to enhance the ideation exercises. Exercise 1 focuses on the ‘Inquire’ phase, Exercise 2 the ‘Inquire’ and ‘Ideate’ phases, and Exercise 3 concentrates on the ‘Implement’ phase. Depending on the intensity of the focus, the unit of work could be developed over a 4-5 week program (approximately 4-6 x 60 minute lessons/workshops) or as smaller workshops treated as discrete learning experiences. The toolkit is available for public download from http://designminds.org.au/the-big-picture/ on the Design Minds website.

Design Minds Tomorrow's Classroom Toolkit

The Design Minds Tomorrow’s Classroom Toolkit was one of six K7-12 secondary school design toolkits commissioned by the State Library of Queensland (SLQ) Asia Pacific Design Library (APDL), to facilitate the delivery of the Stage 1 launch of its Design Minds online platform (www.designminds.org.au) partnership initiative with Queensland Government Arts Queensland and the Smithsonian Cooper-Hewitt National Design Museum, on June 29, 2012. Design Minds toolkits are practical guides, underpinned by a combination of one to three of the Design Minds model phases of ‘Inquire’, ‘Ideate’ and ‘Implement’ (supported by at each stage with structured reflection), to enhance existing school curriculum and empower students with real life design exercises, within the classroom environment. Toolkits directly identify links to Naplan, National Curriculum, C2C and Professional Standards benchmarks, as well as the student capabilities of successful and creative 21st century citizens they seek to engender through design thinking. This toolkit explores, through four distinct exercises, different design tools and ways to approach the future design of environments (classrooms/schools) to facilitate the Reggio Emilia philosophy of learning, while addressing diverse and changing social, cultural, technological and environmental challenges. The Design Minds Tomorrow’s Classroom Toolkit encourages students to explore architecture and interior design, and to think about their (life-long) learning as a product of inspiring interactions with people and the environments around them, and that their potential role in contributing to both delightful and functional design solutions requires a deep understanding of the user experience. More generally, it aims to facilitate awareness in young people, of the role of design in society and the value of design thinking skills in generating strategies to solve basic to complex systemic challenges, as well as to inspire post-secondary pathways and idea generation for education. The toolkit encourages students and teachers to develop sketching, making, communication, presentation and collaboration skills to improve their design process, as well as explore further inquiry (background research) to enhance the ideation exercises. Exercise 1 focuses on the ‘Inquire’ and ‘Ideate’ phases, Exercise 2 on the ‘Inquire’, Exercise 3 builds on ideation skills, and Exercise 4 concentrates on the ‘Implement’ phase. Depending on the intensity of the focus, the unit of work could be developed over a 2-5 week program (approximately 4-10 x 60 minute lessons/workshops) or as smaller workshops treated as discrete learning experiences. The toolkit is available for public download from http://designminds.org.au/tomorrows-classroom/ on the Design Minds website. This toolkit inspired the authorship and facilitation of a 2-day design workshop entitled Learning Environment 2050 at John Paul College, Daisy Hill, Brisbane on the 15-16 August 2013. 120 Grade 7 students and their teachers, under the mentorship of two design academics, 3 QUT design students and a professional architect, as part of a QUT School of Design Project Week community engagement activity, explored the formulation of a participatory design brief for the redesign of the school’s Wesley Precinct (including classrooms, a sustainable farm and recreation areas).

Identifying factors that promote consumer behaviours causing expired domestic food waste

Many commentators argue that domestic food waste is strongly influenced by consumer behaviours. This article reports on a study using mixed-methods to identify key factors responsible for promoting consumer behaviours that lead to domestic food waste through the lens of the Value-Belief-Norm (VBN) theory. Based on the study’s findings, three factors are proposed that cause behaviours that lead to food waste: supply knowledge – does a consumer know what food they have available; location knowledge – does a consumer know where to locate food items, and; food literacy – to what degree do past experience and acquired knowledge impact on a consumer’s food consumption and wastage practices. We analyse the study’s findings in light of a review of literature about consumer food wastage behaviours and in turn, present new insights into consumer behaviour, food waste, and the use of technology to reduce food waste.

Instability of the cellular lipidome with age

The human lens nucleus is formed in utero, and from birth onwards, there appears to be no significant turnover of intracellular proteins or membrane components. Since, in adults, this region also lacks active enzymes, it offers the opportunity to examine the intrinsic stability of macromolecules under physiological conditions. Fifty seven human lenses, ranging in age from 12 to 82 years, were dissected into nucleus and cortex, and the nuclear lipids analyzed by electrospray ionization tandem mass spectrometry. In the first four decades of life, glycerophospholipids (with the exception of lysophosphatidylethanolamines) declined rapidly, such that by age 40, their content became negligible. In contrast the level of ceramides and dihydroceramides, which were undetectable prior to age 30, increased approximately 100-fold. The concentration of sphingomyelins and dihydrosphingomyelins remained unchanged over the whole life span. As a consequence of this marked alteration in composition, the properties of fiber cell membranes in the centre of young lenses are likely to be very different from those in older lenses. Interestingly, the identification of age 40 years as a time of transition in the lipid composition of the nucleus coincides with previously reported macroscopic changes in lens properties (e.g., a massive age-related increase in lens stiffness) and related pathologies such as presbyopia. The underlying reasons for the dramatic change in the lipid profile of the human lens with age are not known, but are most likely linked to the stability of some membrane lipids in a physiological environment.

A molecular phylogeny of the checkered beetles and a description of Epiclininae a new subfamily (Coleoptera: Cleroidea: Cleridae)

We provide the first molecular phylogeny of the clerid lineage (Coleoptera: Cleridae, Thanerocleridae) within the superfamily Cleroidea to examine the two most recently-proposed hypotheses of higher-level classification. Phylogenetic relationships of checkered beetles were inferred from approximately ~5,000nt of both nuclear and mitochondrial rDNA (28S, 16S, and 12S) and the mitochondrial protein-coding gene COI. A worldwide sample of ~70 genera representing almost a quarter of generic diversity of the clerid lineage was included and phylogenies were reconstructed using Bayesian and Maximum Likelihood approaches. Results support the monophyly of many proposed subfamilies but were not entirely congruent with either current classification system. The subfamilial relationships within the Cleridae are resolved with support for three main lineages. Tillinae are supported as the sister group to all other subfamilies within the Cleridae, whereas Thaneroclerinae, Korynetinae and a new subfamily formally described here, Epiclininae subf. n, form a sister group to Clerinae + Hydnocerinae.

Hybrid frequency–time domain models for dynamic response analysis of marine structures

Time-domain models of marine structures based on frequency domain data are usually built upon the Cummins equation. This type of model is a vector integro-differential equation which involves convolution terms. These convolution terms are not convenient for analysis and design of motion control systems. In addition, these models are not efficient with respect to simulation time, and ease of implementation in standard simulation packages. For these reasons, different methods have been proposed in the literature as approximate alternative representations of the convolutions. Because the convolution is a linear operation, different approaches can be followed to obtain an approximately equivalent linear system in the form of either transfer function or state-space models. This process involves the use of system identification, and several options are available depending on how the identification problem is posed. This raises the question whether one method is better than the others. This paper therefore has three objectives. The first objective is to revisit some of the methods for replacing the convolutions, which have been reported in different areas of analysis of marine systems: hydrodynamics, wave energy conversion, and motion control systems. The second objective is to compare the different methods in terms of complexity and performance. For this purpose, a model for the response in the vertical plane of a modern containership is considered. The third objective is to describe the implementation of the resulting model in the standard simulation environment Matlab/Simulink.

Poly[mu5-{hydrogen bis[(E)-cinnamato]}-caesium

In the structure of the title polymeric complex [Cs2(C9H7O2)(C9H8O2)]n, the Cs salt-adduct of trans-cinnamic acid, the Cs+ ions of the two individual irregular CsO8 coordination polyhedra lie on a twofold rotation axis and are linked by four bridging carboxyl O-donors from the two cinnamate ligand species. These two ligand components are inter-linked through a delocalized H atom within a short O...H...O hydrogen bond. Structure extension gives a two-dimensional coordination polymer which lies parallel to (001). The crystal was determined from a crystal twinned by non-merohedry, with a twin component ratio of approximately 1:1.

Research roadmap summary - Integrated Design and Delivery Solutions (IDDS)

Changes in the construction sector are creating opportunities in research to maximise the benefits of those changes and to continue the exciting developments in improved people skills, new processes and developing technologies. Many research centres around the world are investigating aspects of the current changes to drive their particular expertise forward. However, the CIB Integrated Design and Delivery Solutions (IDDS) priority research theme takes a higher-level view of the changes and then focuses down on a prioritised set of research targets. These targets have been investigated, re-focussed and validated over a period of four years through many workshops, conferences and meetings by a wide ranging group of representatives from approximately 90 industry and research organisations. The outcomes of such research, once put into practice should be significantly shortened timespans from conception of need to occupation of new or revised structures. As time is money, the owners will get their investments into productive use sooner, which means a shorter payback time. In addition, there will inevitably be a reduction in construction costs as productivity increases. The improvements in reliable delivery and improved quality currently being seen in relatively simplistic use of Building information Modelling (BIM) (compared to full IDDS) will inevitably continue its on-going trajectory of improvement. We should also consider the wider economic contribution to society that will stem from such improvements and, finally, and by no means unimportantly, the reliable modelling and delivery of sustainability at both the building and estate/ area scale will significantly improve carbon footprints and other sustainable outcomes. Whilst there are huge opportunities for early adopters, the primary risk will be the expansion of the gap between those working in this way and those who are not so advanced or who even refuse to progress . The opportunities to address the significant and widely varying wastes within the structure of the construction sector and within and across projects are huge and timely and industry is encouraged to become involved.

Research roadmap report : Integrated Design and Delivery Solutions (IDDS)

Changes in the construction sector are creating opportunities in research to maximise the benefits of those changes and to continue the exciting developments in improved people skills, new processes and developing technologies. There are many research centres around the world investigating aspects of the current changes to drive their particular expertise forward. However, the CIB Integrated Design and Delivery Solutions (IDDS) priority research theme takes a higher-level view of the changes and then focuses down on a prioritised set of research targets. These targets have been investigated, re-focussed and validated over a period of four years through many workshops, conferences and meetings by a wide ranging group of representatives from approximately 90 industry and research organisations. This roadmap prioritises and details the research to be performed, why and by whom. In particular, some 25 CIB Working Commissions and Task Groups are explained as having potential roles in the delivery of this research theme. We are extremely privileged to have been urged on by such distinguished construction professionals in their forewords and the case for research. The outcomes of such research, once put into practice should be significantly shortened timespans from conception of need to occupation of new or revised structures. As time is money, the owners will get their investments into productive use sooner, which means a shorter payback time. In addition, there will inevitably be a reduction in construction costs as productivity increases. The improvements in reliable delivery and improved quality currently being seen in relatively simplistic use of Building information Modelling (BIM) (compared to full IDDS) will inevitably continue its on-going trajectory of improvement. We should also consider the wider economic contribution to society that will stem from such improvements and, finally, and by no means unimportantly, the reliable modelling and delivery of sustainability at both the building and estate/ area scale will significantly improve carbon footprints and other sustainable outcomes. Whilst there are huge opportunities for early adopters, the primary risk will be the expansion of the gap between those working in this way and those who are not so advanced or who even refuse to progress1. However, a similar issue arises between industry, clients, educators and trainers; the latter have particular challenges, having existed for many years in a sector that has had relatively few technological changes. However, the opportunities to address the significant and widely varying wastes within the structure of the construction sector and within and across projects are huge and timely. Whilst this Roadmap is specifically targeted at the Standing Commissions and Task Groups of the CIB, it is hoped that there are elements for research and applied research across academia and industry.

Experimental and numerical analysis of the relationship between indoor and outdoor airborne particles in an operating room

This work investigated the impact of the HVAC filtration system and indoor particle sources on the relationship between indoor and outdoor airborne particle size and concentrations in an operating room. Filters with efficiency between 65% and 99.97% were used in the investigation and indoor and outdoor particle size and concentrations were measured. A balance mass model was used for the simulation of the impact of the surgical team, deposition rate, HVAC exhaust and air change rates on indoor particle concentration. The experimental results showed that high efficiency filters would not be expected to decrease the risk associated with indoor particles larger than approximately 1 µm in size because normal filters are relatively efficient for these large particles. A good fraction of outdoor particles were removed by deposition on the HVAC system surfaces and this deposition increased with particle size. For particles of 0.3-0.5 µm in diameter, particle reduction was about 23%, while for particles >10 µm the loss was about 78%. The modelling results showed that depending on the type of filter used, the surgical team generated between 93-99% of total particles, while the outdoor air contributed only 1-6%.

The penetrance and characteristics of contact lens wear in Australia

Background A population-based, cross-sectional telephone survey was conducted to estimate the penetrance and characteristics of contact lens wear in Australia. Methods Based on postcode distribution, 42,749 households around Australia were randomly selected from the national electronic telephone directory. During calls, the number of individuals and contact lens wearers in each household aged between 15 and 64 years was ascertained. Contact lens wearers were interviewed using a structured questionnaire, to determine details of demographics, lens type, mode of lens wear and hygienic habits. Contact lens wear characteristics and habits were compared by lens type and mode of use. Results Of the 32,405 households contacted, 19,171 (59.2 per cent) agreed to participate. The penetrance of contact lens wear during the study period was 5.01 per cent (95% CI: 4.78-5.24). The mean age of lens wearers was 36.5 ± 18.3 years and 63.4 per cent were female. There were significant differences in the habits and characteristics of lens wearers depending on their lens type and mode of use. Conclusions The penetrance of contact lens wear concurs with market estimates and equates to approximately 680,000 contact lens wearers aged between 15 and 64 years in Australia. This is the most detailed and extensive population-based survey of contact lens wearers ever conducted. The discrepancies found between the characteristics of lens wearers surveyed in this study compared to those in previous studies of contact lens practitioners highlights the importance of study design. These results may be applied to other regions with similar health-care and regulatory systems.