Monte Carlo-based diode design for correction-less small field dosimetry

Due to their small collecting volume diodes are commonly used in small field dosimetry. However the relative sensitivity of a diode increases with decreasing small field size. Conversely, small air gaps have been shown to cause a significant decrease in the sensitivity of a detector as the field size is decreased. Therefore this study uses Monte Carlo simulations to look at introducing air upstream to diodes such that they measure with a constant sensitivity across all field sizes in small field dosimetry. Varying thicknesses of air were introduced onto the upstream end of two commercial diodes (PTW 60016 photon diode and PTW 60017 electron diode), as well as a theoretical unenclosed silicon chip using field sizes as small as 5 mm × 5 mm . The metric D_(w,Q)/D_(Det,Q) used in this study represents the ratio of the dose to a point of water to the dose to the diode active volume, for a particular field size and location. The optimal thickness of air required to provide a constant sensitivity across all small field sizes was found by plotting D_(w,Q)/D_(Det,Q) as a function of introduced air gap size for various field sizes, and finding the intersection point of these plots. That is, the point at which D_(w,Q)/D_(Det,Q) was constant for all field sizes was found. The optimal thickness of air was calculated to be 3.3 mm, 1.15 mm and 0.10 mm for the photon diode, electron diode and unenclosed silicon chip respectively. The variation in these results was due to the different design of each detector. When calculated with the new diode design incorporating the upstream air gap, k_(Q_clin 〖,Q〗_msr)^(f_clin 〖,f〗_msr ) was equal to unity to within statistical uncertainty (0.5 %) for all three diodes. Cross-axis profile measurements were also improved with the new detector design. The upstream air gap could be implanted on the commercial diodes via a cap consisting of the air cavity surrounded by water equivalent material. The results for the unclosed silicon chip show that an ideal small field dosimetry diode could be created by using a silicon chip with a small amount of air above it.

Cross-layer design and optimization for wireless networked control systems

Wireless networked control systems (WNCSs) have been widely used in the areas of manufacturing and industrial processing over the last few years. They provide real-time control with a unique characteristic: periodic traffic. These systems have a time-critical requirement. Due to current wireless mechanisms, the WNCS performance suffers from long time-varying delays, packet dropout, and inefficient channel utilization. Current wirelessly networked applications like WNCSs are designed upon the layered architecture basis. The features of this layered architecture constrain the performance of these demanding applications. Numerous efforts have attempted to use cross-layer design (CLD) approaches to improve the performance of various networked applications. However, the existing research rarely considers large-scale networks and congestion network conditions in WNCSs. In addition, there is a lack of discussions on how to apply CLD approaches in WNCSs. This thesis proposes a cross-layer design methodology to address the issues of periodic traffic timeliness, as well as to promote the efficiency of channel utilization in WNCSs. The design of the proposed CLD is highlighted by the measurement of the underlying network condition, the classification of the network state, and the adjustment of sampling period between sensors and controllers. This period adjustment is able to maintain the minimally allowable sampling period, and also maximize the control performance. Extensive simulations are conducted using the network simulator NS-2 to evaluate the performance of the proposed CLD. The comparative studies involve two aspects of communications, with and without using the proposed CLD, respectively. The results show that the proposed CLD is capable of fulfilling the timeliness requirement under congested network conditions, and is also able to improve the channel utilization efficiency and the proportion of effective data in WNCSs.

Alternative structural design strategies for bridge decks in low traffic volume roads

This research is part of a major project with a stimulus that rose from the need to manage a large number of ageing bridges in low traffic volume roads (LTVR) in Australia. The project investigated, designed and consequently constructed, involved replacing an ageing super-structure of a 10m span bridge with a disused Flat-bed Rail Wagon (FRW). This research, therefore, is developed on the premises that the FRW can be adopted as the main structural system for the bridges in LTVR network. The main focus of this research is to present two alternate deck wearing systems (DWS) as part of the design of the FRW as road bridge deck conforming to AS5100 (2004). The bare FRW structural components were first examined for their adequacy (ultimate and serviceability) in resisting the critical loads specified in AS5100(2004). Two options of DWSs were evaluated and their effects on the FRW examined. The first option involved usage of timber DWS; the idea of this option was to use all the primary and secondary members of the FRW in load sharing and to provide additional members where weaknesses in the original members arose. The second option involved usage of reinforced concrete DWS with only the primary members of the FRW sharing the AS5100 (2004) loading. This option inherently minimised the risk associated with any uncertainty of the secondary members to their structural adequacy. This thesis reports the design phases of both options with conclusions of the selection of the ideal option for better structural performance, ease of construction and cost. The comparison carried out here focuses on the distribution of the traffic load by the FRW as a superstructure. Advantages and disadvantages highlighting cost comparisons and ease of constructability of the two systems are also included.

Educating the ‘Design Innovation Catalyst’ for change

Conventionally, design has played a compartmental role in the innovation process within most conservative companies around the world. Generally, companies have focused on the product design execution or the manufacturing and production arenas, and in some instances design is seen as merely a stylistic afterthought. Gradually, design is being regarded as a dynamic and central tactical business resource and consequently organisations globally look to design to help them innovate, differentiate and compete in a changing economic climate. Considering this, the question is raised; how can the specific knowledge and skills of designers be better articulated, understood, implemented and valued as a core component of strategic innovation in businesses? In seeking to answer this question, this paper proposes the new frontier of the design profession coined the ‘Design Innovation Catalyst’. This paper outlines the role of the new design professional and discusses the subsequent implications for design education. Furthermore, questions surrounding how designers will develop these new capabilities and how the design led innovation framework in application can contribute to the future of design will also be presented. It is anticipated that the findings from this research will help to better equip designers to enable them to play a more central role in business and strategic innovation now and in the future.

A design led innovation approach to gathering deep customer insights in the aviation industry

Research has long documented the value that design brings to the innovation of products and services. The research landscape has transformed in the last decade and now reflects the value of design as a different way thinking that can be applied to the innovation of business models and catalyst for strategic growth. This paper presents a case study of gathering deep customer insights through a design led innovation approach and reveals industry perspectives and attitudes towards the value of deep customer insights within the context of a leading Australian airport corporation. The findings highlight that the process of gathering deep customer insights encourages a design led approach to testing assumptions and developing stronger customer engagement. The richness of the deep customer insights also provided a bridge to future thought by provoking possible product, service and business innovations which aligned to the airport corporation’s vision. The implications of the study reveal how quantitative market data, which reveals broad sociocultural trends into ‘how’ and ‘what’ customers interact with within an airport, can be strongly validated and built upon through qualitative deep customer insights that explore ‘why’ those choices to interact are made. Future research is then presented which aims to widely disseminate a design led approach to innovation within internal stakeholders of the airport corporation through the development of a digital strategy.

An urban informatics approach to smart city learning in architecture and urban design education

This study aims to redefine spaces of learning to places of learning through the direct engagement of local communities as a way to examine and learn from real world issues in the city. This paper exemplifies Smart City Learning, where the key goal is to promote the generation and exchange of urban design ideas for the future development of South Bank, in Brisbane, Australia, informing the creation of new design policies responding to the needs of local citizens. Specific to this project was the implementation of urban informatics techniques and approaches to promote innovative engagement strategies. Architecture and Urban Design students were encouraged to review and appropriate real-time, ubiquitous technology, social media, and mobile devices that were used by urban residents to augment and mediate the physical and digital layers of urban infrastructures. Our study’s experience found that urban informatics provide an innovative opportunity to enrich students’ place of learning within the city.

Inflow cannula design for biventricular assist devices

Cardiovascular diseases are a leading cause of death throughout the developed world. With the demand for donor hearts far exceeding the supply, a bridge-to-transplant or permanent solution is required. This is currently achieved with ventricular assist devices (VADs), which can be used to assist the left ventricle (LVAD), right ventricle (RVAD), or both ventricles simultaneously (BiVAD). Earlier generation VADs were large, volume-displacement devices designed for temporary support until a donor heart was found. The latest generation of VADs use rotary blood pump technology which improves device lifetime and the quality of life for end stage heart failure patients. VADs are connected to the heart and greater vessels of the patient through specially designed tubes called cannulae. The inflow cannulae, which supply blood to the VAD, are usually attached to the left atrium or ventricle for LVAD support, and the right atrium or ventricle for RVAD support. Few studies have characterized the haemodynamic difference between the two cannulation sites, particularly with respect to rotary RVAD support. Inflow cannulae are usually made of metal or a semi-rigid polymer to prevent collapse with negative pressures. However suction, and subsequent collapse, of the cannulated heart chamber can be a frequent occurrence, particularly with the relatively preload insensitive rotary blood pumps. Suction events may be associated with endocardial damage, pump flow stoppages and ventricular arrhythmias. While several VAD control strategies are under development, these usually rely on potentially inaccurate sensors or somewhat unreliable inferred data to estimate preload. Fixation of the inflow cannula is usually achieved through suturing the cannula, often via a felt sewing ring, to the cannulated chamber. This technique extends the time on cardiopulmonary bypass which is associated with several postoperative complications. The overall objective of this thesis was to improve the placement and design of rotary LVAD and RVAD inflow cannulae to achieve enhanced haemodynamic performance, reduced incidence of suction events, reduced levels of postoperative bleeding and a faster implantation procedure. Specific objectives were: * in-vitro evaluation of LVAD and RVAD inflow cannula placement, * design and in-vitro evaluation of a passive mechanism to reduce the potential for heart chamber suction, * design and in-vitro evaluation of a novel suture-less cannula fixation device. In order to complete in-vitro evaluation of VAD inflow cannulae, a mock circulation loop (MCL) was developed to accurately replicate the haemodynamics in the human systemic and pulmonary circulations. Validation of the MCL’s haemodynamic performance, including the form and magnitude of pressure, flow and volume traces was completed through comparisons of patient data and the literature. The MCL was capable of reproducing almost any healthy or pathological condition, and provided a useful tool to evaluate VAD cannulation and other cardiovascular devices. The MCL was used to evaluate inflow cannula placement for rotary VAD support. Left and right atrial and ventricular cannulation sites were evaluated under conditions of mild and severe heart failure. With a view to long term LVAD support in the severe left heart failure condition, left ventricular inflow cannulation was preferred due to improved LVAD efficiency and reduced potential for thrombus formation. In the mild left heart failure condition, left atrial cannulation was preferred to provide an improved platform for myocardial recovery. Similar trends were observed with RVAD support, however to a lesser degree due to a smaller difference in right atrial and ventricular pressures. A compliant inflow cannula to prevent suction events was then developed and evaluated in the MCL. As rotary LVAD or RVAD preload was reduced, suction events occurred in all instances with a rigid inflow cannula. Addition of the compliant segment eliminated suction events in all instances. This was due to passive restriction of the compliant segment as preload dropped, thus increasing the VAD circuit resistance and decreasing the VAD flow rate. Therefore, the compliant inflow cannula acted as a passive flow control / anti-suction system in LVAD and RVAD support. A novel suture-less inflow cannula fixation device was then developed to reduce implantation time and postoperative bleeding. The fixation device was evaluated for LVAD and RVAD support in cadaveric animal and human hearts attached to a MCL. LVAD inflow cannulation was achieved in under two minutes with the suture-less fixation device. No leakage through the suture-less fixation device – myocardial interface was noted. Continued development and in-vivo evaluation of this device may result in an improved inflow cannulation technique with the potential for off-bypass insertion. Continued development of this research, in particular the compliant inflow cannula and suture-less inflow cannulation device, will result in improved postoperative outcomes, life span and quality of life for end-stage heart failure patients.

Framework for implementing design build project delivery system in road infrastructure in Indonesia

The thesis provides a framework for potential implementation of the design-build (DB) project delivery system in road infrastructure projects in Indonesia. This framework proposed a structure of the hierarchy of factors promoting the potential implementation of the DB project delivery system and introduced ways to implement the DB project delivery system through level of hierarchical factors. These findings not only give benefit to the academic knowledge but also to the public officials in guiding them with regard to the priority of promoting factors in the process to implement the DB system.

Integration of Saudi Arabia’s conservative Islamic culture in sustainable housing design

The cities of Saudi Arabia have perhaps the largest growth rates of cities in the Middle East, such that it has become a cause in shortage of housing for mid and low-income families, as is the case in other developing countries. Even when housing is found, it is not sustainable nor is it providing the cultural needs of those families. The aim of this paper is to integrate the unique conservative Islamic Saudi culture into the design of sustainable housing. This paper is part of a preliminary study of an on-going PhD thesis, which utilises a semistructured interview of a panel of nine experts in collecting the data. The interviews consisted of ten questions ranging from general questions such as stating their expertise and work position to more specific question such as listing the critical success factors and/or barriers for applying sustainability to housing in Saudi Arabia. Since the participants were selected according to their experience, the answers to the interview questions were satisfactory where the generation of the survey questions for the second stage in the PhD thesis took place after analysing the participant’s answers to the interview questions. This paper recommends design requirements for accommodating the conservative Islamic Saudi Culture in low cost sustainable houses. Such requirements include achieving privacy through the use of various types of traditional Saudi architectural elements, such as the method of decorative screening of windows, called Mashrabiya, and having an inner courtyard where the house looks inward rather than outward. Other requirements include educating firms on how to design sustainable housing, educating the public on the advantages of sustainable housing and implementing new laws that enforce the utilisation of sustainable methods to housing construction. This paper contributes towards the body of knowledge by proposing initial findings on how to integrate the conservative Islamic culture of Saudi Arabia into the design of a sustainable house specifically for mid and low-income families. This contribution can be implemented on developing countries in the region that are faced with housing shortage for mid and low-income families.

Design, sustainability and Australian mass-market fashion : three case studies

The production of fashion garments has negative environmental and social impacts that can potentially be reduced through decisions made in the design process. This research explores to what extent Australian mass-market fashion designers consider environmental sustainability within product design. The study presents three case studies from different market levels, assembled through interviews with designers, along with an analysis of the Australian mass-market fashion industry. The project provides insights into the workings of the fashion design process within mid and high volume companies, and identifies opportunities and barriers for consideration of sustainability.

Growing existing aboriginal designs to guide a cross-cultural design project

Designing across cultures requires considerable attention to inter-relational design methods that facilitate mutual exploration, learning and trust. Many Western design practices have been borne of a different model, utilizing approaches for the design team to rapidly gain insight into “users” in order to deliver concepts and prototypes, with little attention paid to different cultural understandings about being, knowledge, participation and life beyond the design project. This paper describes a project that intends to create and grow a sustainable set of technology assisted communication practices for the Warnindilyakwa people of Groote Eylandt in the form of digital noticeboards. Rather than academic practices of workshops, interviews, probes or theoretical discourses that emphasize an outside-in perspective, we emphasize building upon the local designs and practices. Our team combines bilingual members from the local Land Council in collaboration with academics from a remote urban university two thousand kilometers away. We contribute an approach of growing existing local practices and materials digitally in order to explore viable, innovative and sustainable technical solutions from this perspective.

Analysis of the design-construction supply chain in the thermal performance of sub-tropical and tropical housing

Background: In sub-tropical and tropical Queensland, a legacy of poor housing design,minimal building regulations with few compliance measures, an absence of post-construction performance evaluation and various social and market factors has led to a high and growing penetration of, and reliance on, air conditioners to provide thermal comfort for occupants. The pervasive reliance on air conditioners has arguably impacted on building forms, changed cultural expectations of comfort and social practices for achieving comfort, and may have resulted in a loss of skills in designing and constructing high performance building envelopes. Aim: The aim of this paper is to report on initial outcomes of a project that sought to determine how the predicted building thermal performance of twenty-five houses in subtropical and tropical Queensland compared with objective performance measures and comfort performance as perceived by occupants. The purpose of the project was to shed light on the role of various supply chain agents in the realisation of thermal performance outcomes. Methodology: The case study methodology embraced a socio-technical approach incorporating building science and sociology. Building simulation was used to model thermal performance under controlled comfort assumptions and adaptive comfort conditions. Actual indoor climate conditions were measured by temperature and relative humidity sensors placed throughout each house, whilst occupants’ expectations of thermal comfort and their self-reported behaviours were gathered through semi-structured interviews and periodic comfort surveys. Thermal imaging and air infiltration tests, along with building design documents, were analysed to evaluate the influence of various supply chain agents on the actual performance outcomes. Results: The results clearly show that in the housing supply chain – from designer to constructor to occupant – there is limited understanding from each agent of their role in contributing to, or inhibiting, occupants’ comfort.

Hybrid placemaking in the library : designing digital technology to enhance users’ on-site experience

This paper presents research findings and design strategies that illustrate how digital technology can be applied as a tool for hybrid placemaking in ways that would not be possible in purely digital or physical space. Digital technology has revolutionised the way people learn and gather new information. This trend has challenged the role of the library as a physical place, as well as the interplay of digital and physical aspects of the library. The paper provides an overview of how the penetration of digital technology into everyday life has affected the library as a place, both as designed by place makers, and, as perceived by library users. It then identifies a gap in current library research about the use of digital technology as a tool for placemaking, and reports results from a study of Gelatine – a custom built user check-in system that displays real-time user information on a set of public screens. Gelatine and its evaluation at The Edge, at State Library of Queensland illustrates how combining affordances of social, spatial and digital space can improve the connected learning experience among on-site visitors. Future design strategies involving gamifying the user experience in libraries are described based on Gelatine’s infrastructure. The presented design ideas and concepts are relevant for managers and designers of libraries as well as other informal, social learning environments.

Power converters design and analysis for high power piezoelectric ultrasonic transducers

High power piezoelectric ultrasonic transducers have been widely exploited in a variety of applications. The critical behaviour of a piezoelectric device is encapsulated in its resonant frequencies because of its maximum transmission performance at these frequencies. Therefore power electronic converters should be tuned at those resonant frequencies to transfer electrical power to mechanical power efficiently. However, structural and environmental changes cause variations in the device resonant frequencies which can degrade the system performance. Hence, estimating the device resonant frequencies within the incorporated setup can significantly improve the system performance. This paper proposes an efficient resonant frequency estimation approach to maintain the performance of high power ultrasonic applications using the employed power converter. Experimental validations indicate the effectiveness of the proposed method.

Improving the design of online applications for social benefit through a behaviour change model

Community support agencies routinely employ a web presence to provide information on their services. While this online information provision helps to increase an agency’s reach, this paper argues that it can be further extended by mapping relationships between services and by facilitating two-way communication and collaboration with local communities. We argue that emergent technologies, such as locative media and networking tools, can assist in harnessing this social capital. However, new applications must be designed in ways that both persuade and support community members to contribute information and support others in need. An analysis of the online presence of community service agencies and social benefit applications is presented against Fogg’s Behaviour Model. From this evaluation, design principles are proposed for developing new locative, collaborative online applications for social benefit.