Nanoparticle emissions from a fleet of CNG buses in transient and steady state operation

Particle emission measurements from a fleet of 14 CNG and 5 Diesel buses were measured both for transient and steady state mode s on a chassis dynamometer with a CVS dilution system. Several transient DT80 cycles and 4 steady sate modes (0, 25, 50 100% of maximum load) were measured for each bus tested. Particle number concentration data was collected by three CPC’s (TSI 3022, 3010 3782WCPC) having D50 cut-offs set to 5, 10 and 20nm respectively. The size distributions were measured with a TSI 3080 SMPS with a 3025 CPC during the steady state modes. Particle mass emissions were measured with a TSI Dustrak. Particle mass emissions for Diesel buses were upto 2 orders of magnitude higher than for CNG buses. Particle number emissions during steady state modes for Diesel busses were 2 to 5 times higher than for CNG busses for all of the tested loads. On the other hand for the DT80 transient cycle particle number emissions were up to 3 times higher for the CNG buses. More detailed analysis of the transient cycles revealed that the reason for this was due to high particle number emissions from CNG busses during the acceleration parts of the cycles. Particles emitted by the CNG busses during acceleration were in the nucleation mode with the majority being smaller than 10nm. Volatility measurements have also shown that they were highly volatile.

Wet hail and thunderstorm electrification

Hailstones in wet growth are commonly found in thunderclouds. While the ice-ice relative growth rate mechanism is generally accepted as the most likely cause of thunderstorm electrification, it is uncertain if this mechanism will operate under wet growth conditions because ice crystals are more likely to stick to the wet surface of a hailstone rather than bounce off it. Experiments were carried out in the laboratory to investigate if there was any charge separated when vapor-grown ice crystals bounced off a wet hailstone. A cloud of supercooled droplets, with and without ice crystals, was drawn past a simulated hailstone. In the dry growth regime, the hailstone charged strongly positive when droplets and crystals co-existed in the cloud. With only droplets in the cloud, there was no charging in the dry growth regime. However, as the hailstone attained wet growth, positive charging currents of about 0.5 and 3.5 pA were observed at 12 and 20 m s-1, respectively. We hypothesize that this observed charging was due to the evaporation of melt water. This so called Dinger-Gunn Effect is due to the ejection of negatively charged minute droplets produced by air bubbles bursting at the surface of the melt water. However the charge separated in wet growth was an order of magnitude smaller than that in dry growth and, therefore, we conclude that it is unlikely to play an important role in the electrification of thunderstorms.

Beyond the barriers : road construction safety issues from the office and the roadside

Conceptually, the management of safety at roadworks can be seen in a three level framework. At the regulatory level, roadworks operate at the interface between the work environment, governed by workplace health and safety regulations, and the road environment, which is subject to road traffic regulations and practices. At the organizational level, national, state and local governments plan and purchase road construction and maintenance which are then delivered in-house or tendered out to large construction companies who often subcontract multiple smaller companies to supply services and labor. At the operational level, roadworks are difficult to isolate from the general public, hindering effective occupational health and safety controls. This study, from the State of Queensland, Australia, examines how well this tripartite framework functions. It includes reviews of organizational policy and procedures documents; interviews with 24 subject matter experts from various road construction and maintenance organizations, and on-site interviews with 66 road construction personnel. The study identified several factors influencing the translation of safety policies into practice including the cost of safety measures in the context of competitive tendering, lack of firm evidence of the effectiveness of safety measures, and pressures to minimize disruption to the travelling public.

An orientation to early childhood education for sustainability and research : framing the text

This publication arose from the interests of the chapter authors, ‘a small group of thoughtful people’ almost all of whom participated in one or both Transnational Dialogues in Research in Early Childhood Education for Sustainability, held in Stavanger, Norway in 2010 and Brisbane, Australia in 2011 (Refer Appendix 1 for list of participants). These meetings were the first time that a critical mass of researchers from vastly different parts of the globe - Norway, Sweden, Australia and New Zealand at the inaugural meeting, with additional participants from Korea, Japan and Singapore attending the second - had come together to debate, discuss and share ideas about research and theory in the emerging field of Early Childhood Education for Sustainability (ECEfS. Some of the researchers who joined these Transnational Dialogues, had met serendipitously at earlier conferences and meetings, or corresponded via email, but many had never met face-to-face. Now a significant number are contributing authors in this text. It is a testament to these researchers’ interest in this agenda that they mostly self-funded their travel and other costs to attend the Transnational Dialogues research meetings. While most chapter authors come from the field of early childhood education, a few are more aligned with education for sustainability/environmental education, while a much smaller number are already working at the intersection of early childhood education and education for sustainability. What we share as a group is a range of perspectives and orientations to research and to the research focus at the heart of this book - young children and their actual and potential capabilities as agents of change for sustainability. As researchers, regardless of experience and perspectives, participants knew they had something extra to offer - their expertise as researchers - providing scholarly insights into the work of practitioners, applying critically reflective lenses to curricula, pedagogies and assumptions, testing of ideas and theories, and presenting a sense for where ECEfS might fit or, indeed, go beyond norms and orthodoxies. This is a text, then, for both researchers and those whose primary interests lie in daily interactions with children, families and communities.

Prediction of thermal expansion properties of carbon nanotubes using molecular dynamics simulations

The axial coefficients of thermal expansion (CTE) of various carbon nanotubes (CNTs), i.e., single-wall carbon nanotubes (SWCNTs), and some multi-wall carbon nanotubes (MWCNTs), were predicted using molecular dynamics (MDs) simulations. The effects of two parameters, i.e., temperature and the CNT diameter, on CTE were investigated extensively. For all SWCNTs and MWCNTs, the obtained results clearly revealed that within a wide low temperature range, their axial CTEs are negative. As the diameter of CNTs decreases, this temperature range for negative axial CTEs becomes narrow, and positive axial CTEs appear in high temperature range. It was found that the axial CTEs vary nonlinearly with the temperature, however, they decrease linearly as the CNT diameter increases. Moreover, within a wide temperature range, a set of empirical formulations was proposed for evaluating the axial CTEs of armchair and zigzag SWCNTs using the above two parameters. Finally, it was found that the absolute value of the negative axial CTE of any MWCNT is much smaller than those of its constituent SWCNTs, and the average value of the CTEs of its constituent SWCNTs. The present fundamental study is very important for understanding the thermal behaviors of CNTs in such as nanocomposite temperature sensors, or nanoelectronics devices using CNTs.

Solution-processed dual-gate polymer field-effect transistors for display applications

We describe the advantages of dual-gate thin-film transistors (TFTs) for display applications. We show that in TFTs with active semiconductor layers composed of diketopyrrolopyrrole-naphthalene copolymer, the on-current is increased, the off-current is reduced, and the sub-threshold swing is improved compared to single-gate devices. Charge transport measurements in steady-state and under non-quasi-static conditions reveal the reasons for this improved performance. We show that in dual-gate devices, a much smaller fraction of charge carriers move in slow trap states. We also compare the activation energies for charge transport in the top-gate and bottom-gate configurations.

Small firms and the challenge of equality, diversity and difference

Purpose The purpose of this paper is to introduce the papers contributing to this special issue and to locate them within the broader questions about the role of small firms in enabling or alleviating issues of equality, diversity, and difference for various groups in society. Design/methodology/approach The literature dealing with the issues of equality, diversity, and difference pertaining to the operation of and/or working in smaller firms was reviewed prior to drawing out the key points from the submitted papers and considering the contribution they make to this literature. Findings Overall, one's these five papers contribute to one's understanding of the issues facing those in business or self‐employment, working in small business or wanting to pursue enterprise. Originality/value Rarely are questions asked about the assumed role small firms play in mitigating social exclusion for a range of groups in society. By addressing questions which explore the challenge of equality, diversity, and difference for small business in their establishment, management, and effective operation using interdisciplinary frameworks and different methodologies, a better understanding of the role of small business in society can be developed.

Small firms, the paid maternity leave debate in Australia and the business case

Purpose The purpose of this paper is to examine the management of maternity leave in small firms and particularly to explore the perceived costs and benefits of paid maternity leave (PML). PML is a universal right in some countries (i.e. the UK), but not in Australia where most private sector female employees only have access to 12 months unpaid maternity leave. It also aims to explore how the business case for (or against) PML is constructed in small firms. Design/methodology/approach The study was limited to smaller firms operating in the business services sector in the same regional area. Semi‐structured interviews were conducted with eight employers and female employees in six of these firms. Analysis by theme was undertaken within and across interview transcripts. Findings Not one of these small firm employers offered PML and the cost of doing so was not considered to outweigh the benefits already realised through the (legislated) unpaid maternity leave scheme. In these firms maternity leave was managed in an informal way with notions of flexibility – give and take – characterising what happens. Originality/value The paper addresses the lack of research on access to family‐related leave policies in small firms. Employer and employee views of the issue are drawn upon, the latter not often being heard. The paper contributes to understanding the construction of the business case for a specific issue in smaller firms and human resource management from a resource‐based view more generally in smaller firms.

Introduction : At the Intersection of Entrepreneurship and Human Resource Management

In recent years there has been a growing literature on human resource management (HRM) and smaller firms which has also encompassed firms that are growing and entrepreneurial. For example we have seen a special edition of Entrepreneurship Theory and Practice (Katz et al., 2000), two of Human Resource Management Review (Baron, 2003; Barrett and Mayson, 2006) and one of Human Resource Management (Huselid, 2003; Tansky and Heneman, 2003), with another of Human Resource Management (to be edited by Ribeiro, Roig and Tansky) scheduled for publication in 2010. In addition, symposia on the topic have been undertaken at the Academy of Management in 2005 (organized by Mayson) and in 2004 (organized by Hayton). Papers dealing with issues of HRM for new, small, growing and/or entrepreneurial firms have been presented at a range of different conferences, whether they are management oriented such as the Academy of Management (AoM) and its regional variants (for example, the British Academy of Management (BAM) or the Australian and New Zealand Academy of Management (ANZAM)), entrepreneurially focused ones like the Babson College Entrepreneurship Research conference or ones focused specifically on smaller firms such as the conferences of the Institute for Small Business and Entrepreneurship (ISBE) in the UK or the International Council for Small Business (ICSB) and its regional affiliates. With all these papers and all this discussion is there anything left to say? Well yes, we think there is and we are...

Determinants of plant performance dynamics : empirical analysis of the manufacturing sector in Indonesia, 1990-2000

We identify determinants of plant dynamics and find their differences before, during, and after the Asian financial crisis. The results show that the distinction of the crisis is important and the effects of the crisis do not seem to persist after 1998. Furthermore, we reject Gibrat's law as the right functional form to describe plant growth. We are not able to support empirically the theoretical results that smaller and efficient plants tend to grow faster than larger and inefficient plants with the exception of the crisis period. The results reflect that there was a trickle down effect of economic development.

Quality assurance of aerial applications of larvicides for mosquito control : effects of granule and catch tray size on field monitoring programs

Aerial applications of granular insecticides are preferable because they can effectively penetrate vegetation, there is less drift, and no loss of product due to evaporation. We aimed to 1) assess the field efficacy ofVectoBac G to control Aedes vigilax (Skuse) in saltmarsh pools, 2) develop a stochastic-modeling procedure to monitor application quality, and 3) assess the distribution of VectoBac G after an aerial application. Because ground-based studies with Ae. vigilax immatures found that VectoBac G provided effective control below the recommended label rate of 7 kg/ha, we trialed a nominated aerial rate of 5 kg/ha as a case study. Our distribution pattern modeling method indicated that the variability in the number of VectoBac G particles captured in catch-trays was greater than expected for 5 kg/ha and that the widely accepted contour mapping approach to visualize the deposition pattern provided spurious results and therefore was not statistically appropriate. Based on the results of distribution pattern modeling, we calculated the catch tray size required to analyze the distribution of aerially applied granular formulations. The minimum catch tray size for products with large granules was 4 m2 for Altosid pellets and 2 m2 for VectoBac G. In contrast, the minimum catch-tray size for Altosid XRG, Aquabac G, and Altosand, with smaller granule sizes, was 1 m2. Little gain in precision would be made by increasing the catch-tray size further, when the increased workload and infrastructure is considered. Our improved methods for monitoring the distribution pattern of aerially applied granular insecticides can be adapted for use by both public health and agricultural contractors.

Loss Control

A exhibition of sculptural assemblages that continue my exploration of self-portraiture and the sculptural object. The work specifically extends the formal vocabulary of my studio to incorporate smaller composite arrangements with an emphasis on the sculptural support. Small objects that are either modelled or cast from life are assembled into four tableaux that respond to the object-relations that arise through the production process. The resulting exhibiton thus acts a meditation on the ontology of art practice, conceived as a topology of objects.

Vision-based simultaneous localization and mapping in changing outdoor environments

For robots operating in outdoor environments, a number of factors, including weather, time of day, rough terrain, high speeds, and hardware limitations, make performing vision-based simultaneous localization and mapping with current techniques infeasible due to factors such as image blur and/or underexposure, especially on smaller platforms and low-cost hardware. In this paper, we present novel visual place-recognition and odometry techniques that address the challenges posed by low lighting, perceptual change, and low-cost cameras. Our primary contribution is a novel two-step algorithm that combines fast low-resolution whole image matching with a higher-resolution patch-verification step, as well as image saliency methods that simultaneously improve performance and decrease computing time. The algorithms are demonstrated using consumer cameras mounted on a small vehicle in a mixed urban and vegetated environment and a car traversing highway and suburban streets, at different times of day and night and in various weather conditions. The algorithms achieve reliable mapping over the course of a day, both when incrementally incorporating new visual scenes from different times of day into an existing map, and when using a static map comprising visual scenes captured at only one point in time. Using the two-step place-recognition process, we demonstrate for the first time single-image, error-free place recognition at recall rates above 50% across a day-night dataset without prior training or utilization of image sequences. This place-recognition performance enables topologically correct mapping across day-night cycles.

What is the apparent angle of a Kelvin ship wave pattern?

While the half-angle which encloses a Kelvin ship wave pattern is commonly accepted to be 19.47 degrees, recent observations and calculations for sufficiently fast-moving ships suggest that the apparent wake angle decreases with ship speed. One explanation for this decrease in angle relies on the assumption that a ship cannot generate wavelengths much greater than its hull length. An alternative interpretation is that the wave pattern that is observed in practice is defined by the location of the highest peaks; for wakes created by sufficiently fast-moving objects, these highest peaks no longer lie on the outermost divergent waves, resulting in a smaller apparent angle. In this paper, we focus on the problems of free surface flow past a single submerged point source and past a submerged source doublet. In the linear version of these problems, we measure the apparent wake angle formed by the highest peaks, and observe the following three regimes: a small Froude number pattern, in which the divergent waves are not visible; standard wave patterns for which the maximum peaks occur on the outermost divergent waves; and a third regime in which the highest peaks form a V-shape with an angle much less than the Kelvin angle. For nonlinear flows, we demonstrate that nonlinearity has the effect of increasing the apparent wake angle so that some highly nonlinear solutions have apparent wake angles that are greater than Kelvin's angle. For large Froude numbers, the effect on apparent wake angle can be more dramatic, with the possibility of strong nonlinearity shifting the wave pattern from the third regime to the second. We expect our nonlinear results will translate to other more complicated flow configurations, such as flow due to a steadily moving closed body such as a submarine.

Encapsulation of Hydrocortisone and Mesalazine in Zein Microparticles

Zein was investigated for use as an oral-drug delivery system by loading prednisolone into zein microparticles using coacervation. To investigate the adaptability of this method to other drugs, zein microparticles were loaded with hydrocortisone, which is structurally related to prednisolone; or mesalazine, which is structurally different having a smaller LogP and ionizable functional groups. Investigations into the in vitro digestibility, and the electrophoretic profile of zein, and zein microparticles were conducted to shed further insight on using this protein as a drug delivery system. Hydrocortisone loading into zein microparticles was comparable with that reported for prednisolone, but mesalazine loading was highly variable. Depending on the starting quantities of hydrocortisone and zein, the average amount of microparticles equivalent to 4 mg hydrocortisone, (a clinically used dose), ranged from 60-115 mg, which is realistic and practical for oral dosing. Comparatively, an average of 2.5 g of microparticles was required to deliver 250 mg of mesalazine (a clinically used dose), so alternate encapsulation methods that can produce higher and more precise mesalazine loading are required. In vitro protein digestibility revealed that zein microparticles were more resistant to digestion compared to the zein raw material, and that individual zein peptides are not preferentially coacervated into the microparticles. In combination, these results suggest that there is potential to formulate a delivery system based on zein microparticles made using specific subunits of zein that is more resistant to digestion as starting material, to deliver drugs to the lower gastrointestinal tract.