Profiling and characterisation of key weather variables and their implication on building design

Local climate is a critical element in the design of buildings. In this paper, ten years of historical weather data in Australia's all eight capital cities are analyzed to characterize the variation profiles of climatic variables. The method of descriptive statistics is employed. Either the pattern of cumulative distribution and/or the profile of percentage distribution are used to graphically illustrate the similarity and difference between different study locations. It is found that although the weather variables vary with different locations, except for the extreme parts, there is often a good, nearly linear relation between weather variable and its cumulative percentage for the majority of middle part. The implication of these extreme parts and the slopes of the middle parts on building design is also discussed.

An investigation of building physical properties selection to combat global warming

Global warming can have a significant impact on building energy performance and indoor thermal environment, as well as the health and productivity of people living and working inside them. Through the building simulation technique, this paper investigates the adaptation potential of different selections of building physical properties to increased outdoor temperature in Australia. It is found that overall, an office building with lower insulation level, smaller window to wall ratio and/or a glass type with lower shading coefficient, and lower internal load density will have the effect of lowering building cooling load and total energy use, and therefore have a better potential to adapt to the warming external climate. Compared with clear glass, it is shown that the use of reflective glass for the sample building with WWR being 0.5 reduces the building cooling load by more than 12%. A lower internal load can also have a significant impact on the reduction of building cooling load, as well as the building energy use. Through the comparison of results between current and future weather scenarios, it is found that the patterns found in the current weather scenario also exist in the future weather scenarios, but to a smaller extent.

Sensitivity of office building zones to global warming

As global warming entails new conditions for the built environment, the thermal behavior of existing buildings, which were designed based on current weather data, may become unclear and remain a great concern. Through building computer simulation, this paper investigates the sensitivity of different office building zoning to the potential global warming. From the sample office building examined, it is found that compared with the middle and top floors, the ground floor for most cities appears to be most sensitive to the effect of global warming and has the highest tendency to having the overheating problem. From the analysis of the responses of different zone orientations to the outdoor air temperature increase, it is also found that there are widely different responses between different zone orientations, with South or Core zone being most sensitive. With an increased external air temperature, the difference between different floors or different zone orientations will become more significant.

The resourceful adolescent project : building psychological resilience in adolescents and their parents

"The model of adolescent depression underlying the Resourceful Adolescent Project (RAP) suggests that adolescent depression and suicide result from a combination of some or all of three interrelating factors: (a) deficits in adolescent psychological wellbeing and coping resources; (b) escalating or chronic family conflict; and (c) depressive adolescent thoughts, feelings and behaviour. This overview of the activities of RAP outlines the need for the project, the benefits of early intervention in preventing adolescent depression, and the empirical and theoretical bases of the programs used in the project. The programs for adolescents and for their parents, their efficacy and the future directions of RAP are also discussed." -- from Libraries Australia

Economic fluctuations and productivity in the Malaysian construction sector

Growth in productivity is the key determinant of the long-term health and prosperity of an economy. The construction industry being one of major strategic importance, its productivity performance has a significant effect on national economic growth. The relationship between construction output and economy has received intensive studies, but there is lack of empirical study on the relationship between construction productivity and economic fluctuations. Fluctuations in construction output are endemic in the industry. In part they are caused by the boom and slump of the economy as a whole and in part by the nature of the construction product. This research aims to uncover how the productivity of construction sector is influenced in the course of economic fluctuations in Malaysia. Malaysia has adopted three economic policies – New Economic Policy (1971-1990), National Development Policy (1991-2000) and the National Vision Policy (2001-2010) since gaining independence in 1959. The Privatisation Master Plan was introduced in 1991. Operating within this historical context, the Malaysian construction sector has experienced four business cycles since 1960. A mixed-method design approach is adopted in this study. Quantitative analysis was conducted on the published official statistics of the construction industry and the overall economy in Malaysia between 1970 and 2009. Qualitative study involved interviews with a purposive sample of 21 industrial participants. This study identified a 32-year long building cycle appears in 1975-2006. It is superimposed with three shorter construction business cycles in 1975-1987, 1987-1999 and 1999-2006. The correlations of Construction labour productivity (CLP) and GDP per capita are statistically significant for the 1975-2006 building cycle, 1987-1999 and 1999-2006 construction business cycles. It was not significant in 1975-1987 construction business cycles. The Construction Industry Surveys/Census over the period from 1996 to 2007 show that the average growth rate of total output per employee expanded but the added value per employee contracted which imply high cost of bought-in materials and services and inefficient usage of purchases. The construction labour productivity is peaked at 2004 although there is contraction of construction sector in 2004. The residential subsector performed relatively better than the other sub-sectors in most of the productivity indicators. Improvements are found in output per employee, value added per employee, labour competitiveness and capital investment but declines are recorded in value added content and capital productivity. The civil engineering construction is most productive in the labour productivity nevertheless relatively poorer in the capital productivity. The labour cost is more competitive in the larger size establishment. The added value per labour cost is higher in larger sized establishment attributed to efficient in utilization of capital. The interview with the industrial participant reveals that the productivity of the construction sector is influenced by the economic environment, the construction methods, contract arrangement, payment chain and regulatory policies. The fluctuations of construction demand have caused companies switched to defensive strategy during the economic downturn and to ensure short-term survival than to make a profit for the long-term survival and growth. It leads the company to take drastic measures to curb expenses, downsizing, employ contract employment, diversification and venture overseas market. There is no empirical evidence supports downsizing as a necessary step in a process of reviving productivity. The productivity does not correlate with size of firm. A relatively smaller and focused firm is more productive than the larger and diversified organisation. However diversified company experienced less fluctuation in both labour and capital productivity. In order to improve the productivity of the construction sector, it is necessary to remove the negatives and flaws from past practices. The recommended measures include long-term strategic planning and coordinated approaches of government agencies in planning of infrastructure development and to provide regulatory environments which encourage competition and facilitate productivity improvement.

What explains the association between socioeconomic status and depression among Vietnamese adults?

Background Depression is a major public health problem worldwide and is currently ranked second to heart disease for years lost due to disability. For many decades, international research has found that depressive symptoms occur more frequently among low socioeconomic (SES) individuals than their more-advantaged peers. However, the reasons as to why those of low socioeconomic groups suffer more depressive symptoms are not well understood. Studies investigating the prevalence of depression and its association with SES emanate largely from developed countries, with little research among developing countries. In particular, there is a serious dearth of research on depression and no investigation of its association with SES in Vietnam. The aims of the research presented in this Thesis are to: estimate the prevalence of depressive symptoms among Vietnamese adults, examine the nature and extent of the association between SES and depression and to elucidate causal pathways linking SES to depressive symptoms Methods The research was conducted between September 2008 and November 2009 in Hue city in central Vietnam and used a combination of qualitative (in-depth interviews) and quantitative (survey) data collection methods. The qualitative study contributed to the development of the theoretical model and to the refinement of culturally-appropriate data collection instruments for the quantitative study. The main survey comprised a cross-sectional population–based survey with randomised cluster sampling. A sample of 1976 respondents aged between 25-55 years from ten randomly-selected residential zones (quarters) of Hue city completed the questionnaire (response rate 95.5%). Measures SES was classified using three indicators: education, occupation and income. The Center for Epidemiologic Studies-Depression (CES-D) scale was used to measure depressive symptoms (range0-51, mean=11.0, SD=8.5). Three cut-off points for the CES-D scores were applied: ‘at risk for clinical depression’ (16 or above), ‘depressive symptoms’ (above 21) and ‘depression’ (above 25). Six psychosocial indicators: life time trauma, chronic stress, recent life events, social support, self esteem, and mastery were hypothesized to mediate the association between SES and depressive symptoms. Analyses The prevalence of depressive symptoms were analysed using bivariate analyses. The multivariable analytic phase comprised of ordinary least squares regression, in accordance with Baron and Kenny’s three-step framework for mediation modeling. All analyses were adjusted for a range of confounders, including age, marital status, smoking, drinking and chronic diseases and the mediation models were stratified by gender. Results Among these Vietnamese adults, 24.3% were at or above the cut-off for being ‘at risk for clinical depression’, 11.9% were classified as having depressive symptoms and 6.8% were categorised as having depression. SES was inversely related to depressive symptoms: the least educated those with low occupational status or with the lowest incomes reported more depressive symptoms. Socioeconomicallydisadvantaged individuals were more likely to report experiencing stress (life time trauma, chronic stress or recent life events), perceived less social support and reported fewer personal resources (self esteem and mastery) than their moreadvantaged counterparts. These psychosocial resources were all significantly associated with depressive symptoms independent of SES. Each psychosocial factor showed a significant mediating effect on the association between SES and depressive symptoms. This was found for all measures of SES, and for males and females. In particular, personal resources (mastery, self esteem) and chronic stress accounted for a substantial proportion of the variation in depressive symptoms between socioeconomic groups. Social support and recent life events contributed modestly to socioeconomic differences in depressive symptoms, whereas lifetime trauma contributed the least to these inequalities. Conclusion This is the first known study in Vietnam or any developing country to systematically examine the extent to which psychosocial factors mediate the relationship between SES and depression. The study contributes new evidence regarding the burden of depression in Vietnam. The findings have practical relevance for advocacy, for mental health promotion and health-care services, and point to the need for programs that focus on building a sense of personal mastery and self esteem. More broadly, the work presented in this Thesis contributes to the international scientific literature on the social determinants of depression.

Building the profession together : towards holistic library and information science education

How can a holistic approach to library and information science education encompassing vocational and university sectors that meets the future information workforce requirements be achieved? This paper will outline a twelve month national project that considered this very question. Funded by the Australian Learning and Teaching Council (ALTC).

Green buildings for greying people : a case study of a retirement village in Australia

Purpose With an increasingly ageing population and widespread acceptance of the need for sustainable development in Australia, the demand for green retirement villages is increasing. This paper aims to identify the critical issues to be considered by developers and practitioners when embarking on their first green residential retirement project in Australia. Design/methodology/approach In view of the lack of adequate historical data for quantitative analysis, a case study approach is employed to examine the successful delivery of green retirement villages. Face-to-face interviews and document analysis were conducted for data collection. Findings The findings of the study indicate that one of the major obstacles to the provision of affordable green retirement villages is the higher initial costs involved. However, positive aspects were identified, the most significant of which relate to: the innovative design of site and floor plans; adoption of thermally efficient building materials; orientation of windows; installation of water harvesting and recycling systems, water conservation fittings and appliances; and waste management during the construction stage. With the adoption of these measures, it is believed that sustainable retirement development can be achieved without significant additional capital costs. Practical implications The research findings serve as a guide for developers in decision making throughout the project life-cycle when introducing green features into the provision of affordable retirement accommodation. Originality/value This paper provides insights into the means by which affordable green residential retirement projects for aged people can be successfully completed.

New strategies of managing waste in office building retrofit projects

Retrofit projects are different from newly-built projects in many respects. A retrofit project involves an existing building, which imposes constraints on the owners, designers, operators and constructors throughout the project process. Retrofit projects are risky, complex, less predictable and difficult to be well planned, which need greater coordination. For office building retrofit project, further restrictions will apply as these buildings often locate in CBD areas and most have to remain operational during the progression of project work. Issues such as site space, material storage and handling, noise and dust, need to be considered and well addressed. In this context, waste management is even more challenging with small spaces for waste handling, uncertainties in waste control, and impact of waste management activities on project delivery and building occupants. Current literatures on waste management in office building retrofit projects focus on increasing waste recovery rate based on project planning, monitoring and stakeholders’ collaboration. However, previous research has not produced knowledge of understanding the particular retrofit processes and their impact on waste generation and management. This paper discusses the interim results of a continuing research on new strategies for waste management in office building retrofit projects. Firstly based on the literature review, it summarizes the unique characteristics of office building retrofit projects and their influence on waste management. An assumption on waste management strategies is formed. Semi-structured interviews were conducted towards industry practitioners and findings are then presented in the paper. The assumption of the research was validated in the interviews from the opinions and experiences of the respondents. Finally the research develops a process model for waste management in office building retrofit projects. It introduces two different waste management strategies. For the dismantling phase, waste is generated fast along with the work progress, so integrated planning for project delivery and waste generation is needed in order to organize prompt handling and treatment. For the fit-out phase, the work is similar as new construction. Factors which are particularly linked to generating waste on site need to be controlled and monitored. Continuing research in this space will help improve the practice of waste management in office building retrofit projects. The new strategies will help promote the practicality of project waste planning and management and stakeholders’ capability of coordinating waste management and project delivery.

Creativity in policing: building the necessary skills to solve complex and protracted investigations

Despite an increased focus on proactive policing in recent years, criminal investigation is still perhaps the most important task of any law enforcement agency. As a result, the skills required to carry out a successful investigation or to be an ‘effective detective’ have been subjected to much attention and debate (Smith and Flanagan, 2000; Dean, 2000; Fahsing and Gottschalk, 2008:652). Stelfox (2008:303) states that “The service’s capacity to carry out investigations comprises almost entirely the expertise of investigators.” In this respect, Dean (2000) highlighted the need to profile criminal investigators in order to promote further understanding of the cognitive approaches they take to the process of criminal investigation. As a result of his research, Dean (2000) produced a theoretical framework of criminal investigation, which included four disparate cognitive or ‘thinking styles’. These styles were the ‘Method’, ‘Challenge’, ‘Skill’ and ‘Risk’. While the Method and Challenge styles deal with adherence to Standard Operating Procedures (SOPs) and the internal ‘drive’ that keeps an investigator going, the Skill and Risk styles both tap on the concept of creativity in policing. It is these two latter styles that provide the focus for this paper. This paper presents a brief discussion on Dean’s (2000) Skill and Risk styles before giving an overview of the broader literature on creativity in policing. The potential benefits of a creative approach as well as some hurdles which need to be overcome when proposing the integration of creativity within the policing sector are then discussed. Finally, the paper concludes by proposing further research into Dean’s (2000) skill and risk styles and also by stressing the need for significant changes to the structure and approach of the traditional policing organisation before creativity in policing is given the status it deserves.

Unfair terms in residential land contracts : will the Australian consumer law improve a buyer’s bargaining position?

The prohibition on unfair contract terms in standard form consumer contracts has the potential to significantly impact on the terms of contracts for the sale of land. The definition of ‘consumer contract’ includes contracts for the sale or grant of an interest in land to an individual wholly or predominantly for personal or domestic use. Therefore, a contract for the purchase of a residence for personal occupation by the buyer, as opposed to a purchase for investment purposes, will be a consumer contract potentially attracting the application of the unfair terms provisions. Significant consumer protection mechanisms already exist in most state jurisdictions requiring disclosure of relevant matters to the buyer and providing remedies for the provision of misleading conduct. Minimal evidence of unfair terms in land contract was presented to the Productivity Commission Inquiry into the Australian Consumer Policy Framework raising the question as to whether there is an identified problem of unfair terms in real estate contracts and if so, whether the same economic and ethical rationales justify regulatory intervention. This article examines what effect if any the introduction of the unfair contract provisions will have on the enforcement of residential land contracts and the viability of previously accepted conditions if challenged as being “unfair terms”. The article concludes that despite the existence of several potentially unfair terms in some land contracts, the intervention of the rules of equity to overcome perceived hardship or unfairness to buyers from strict enforcement of terms means the unfair terms provisions are only likely to operate on terms untouched by those principles. In the authors’ view the scope for operation of the unfair terms provisions will be limited to terms untouched by the principles of equity and consumer protection legislation making it unlikely that there will be any significant realignment of the contractual obligations and rights of buyers and sellers of land.

An accounting standard for nonprofits : the missing essential building blocks

There have been numerous calls over the years for the development of an accounting standard for not-for-profit entities (NFPEs). Probably the most commonly quoted in this regard is that from the Industry Commission Report No. 45 in 1995 which contained the following recommendation: The Commonwealth government should provide funds to the Australian Accounting Standards Board and the Public Sector Accounting Standards Board to develop within two years suitable accounting standards for Community Social Welfare Organisations. This recommendation was made over 5-years ago. Why has no action been taken towards its implementation?...

An analysis of holding cost impact on housing affordability in relation to midsized Greenfield residential property developments in South East Queensland

The position of housing demand and supply is not consistent. The Australian situation counters the experience demonstrated in many other parts of the world in the aftermath of the Global Financial Crisis, with residential housing prices proving particularly resilient. A seemingly inexorable housing demand remains a critical issue affecting the socio-economic landscape. Underpinned by high levels of population growth fuelled by immigration, and further buoyed by sustained historically low interest rates, increasing income levels, and increased government assistance for first home buyers, this strong housing demand level ensures problems related to housing affordability continue almost unabated. A significant, but less visible factor impacting housing affordability relates to holding costs. Although only one contributor in the housing affordability matrix, the nature and extent of holding cost impact requires elucidation: for example, the computation and methodology behind the calculation of holding costs varies widely - and in some instances completely ignored. In addition, ambiguity exists in terms of the inclusion of various elements that comprise holding costs, thereby affecting the assessment of their relative contribution. Such anomalies may be explained by considering that assessment is conducted over time in an ever-changing environment. A strong relationship with opportunity cost - in turn dependant inter alia upon prevailing inflation and / or interest rates - adds further complexity. By extending research in the general area of housing affordability, this thesis seeks to provide a detailed investigation of those elements related to holding costs specifically in the context of midsized (i.e. between 15-200 lots) greenfield residential property developments in South East Queensland. With the dimensions of holding costs and their influence over housing affordability determined, the null hypothesis H0 that holding costs are not passed on can be addressed. Arriving at these conclusions involves the development of robust economic and econometric models which seek to clarify the componentry impacts of holding cost elements. An explanatory sequential design research methodology has been adopted, whereby the compilation and analysis of quantitative data and the development of an economic model is informed by the subsequent collection and analysis of primarily qualitative data derived from surveying development related organisations. Ultimately, there are significant policy implications in relation to the framework used in Australian jurisdictions that promote, retain, or otherwise maximise, the opportunities for affordable housing.

A hierarchical evolutionary algorithmic design (HEAD) system for generating and evolving building design models

This thesis develops a detailed conceptual design method and a system software architecture defined with a parametric and generative evolutionary design system to support an integrated interdisciplinary building design approach. The research recognises the need to shift design efforts toward the earliest phases of the design process to support crucial design decisions that have a substantial cost implication on the overall project budget. The overall motivation of the research is to improve the quality of designs produced at the author's employer, the General Directorate of Major Works (GDMW) of the Saudi Arabian Armed Forces. GDMW produces many buildings that have standard requirements, across a wide range of environmental and social circumstances. A rapid means of customising designs for local circumstances would have significant benefits. The research considers the use of evolutionary genetic algorithms in the design process and the ability to generate and assess a wider range of potential design solutions than a human could manage. This wider ranging assessment, during the early stages of the design process, means that the generated solutions will be more appropriate for the defined design problem. The research work proposes a design method and system that promotes a collaborative relationship between human creativity and the computer capability. The tectonic design approach is adopted as a process oriented design that values the process of design as much as the product. The aim is to connect the evolutionary systems to performance assessment applications, which are used as prioritised fitness functions. This will produce design solutions that respond to their environmental and function requirements. This integrated, interdisciplinary approach to design will produce solutions through a design process that considers and balances the requirements of all aspects of the design. Since this thesis covers a wide area of research material, 'methodological pluralism' approach was used, incorporating both prescriptive and descriptive research methods. Multiple models of research were combined and the overall research was undertaken following three main stages, conceptualisation, developmental and evaluation. The first two stages lay the foundations for the specification of the proposed system where key aspects of the system that have not previously been proven in the literature, were implemented to test the feasibility of the system. As a result of combining the existing knowledge in the area with the newlyverified key aspects of the proposed system, this research can form the base for a future software development project. The evaluation stage, which includes building the prototype system to test and evaluate the system performance based on the criteria defined in the earlier stage, is not within the scope this thesis. The research results in a conceptual design method and a proposed system software architecture. The proposed system is called the 'Hierarchical Evolutionary Algorithmic Design (HEAD) System'. The HEAD system has shown to be feasible through the initial illustrative paper-based simulation. The HEAD system consists of the two main components - 'Design Schema' and the 'Synthesis Algorithms'. The HEAD system reflects the major research contribution in the way it is conceptualised, while secondary contributions are achieved within the system components. The design schema provides constraints on the generation of designs, thus enabling the designer to create a wide range of potential designs that can then be analysed for desirable characteristics. The design schema supports the digital representation of the human creativity of designers into a dynamic design framework that can be encoded and then executed through the use of evolutionary genetic algorithms. The design schema incorporates 2D and 3D geometry and graph theory for space layout planning and building formation using the Lowest Common Design Denominator (LCDD) of a parameterised 2D module and a 3D structural module. This provides a bridge between the standard adjacency requirements and the evolutionary system. The use of graphs as an input to the evolutionary algorithm supports the introduction of constraints in a way that is not supported by standard evolutionary techniques. The process of design synthesis is guided as a higher level description of the building that supports geometrical constraints. The Synthesis Algorithms component analyses designs at four levels, 'Room', 'Layout', 'Building' and 'Optimisation'. At each level multiple fitness functions are embedded into the genetic algorithm to target the specific requirements of the relevant decomposed part of the design problem. Decomposing the design problem to allow for the design requirements of each level to be dealt with separately and then reassembling them in a bottom up approach reduces the generation of non-viable solutions through constraining the options available at the next higher level. The iterative approach, in exploring the range of design solutions through modification of the design schema as the understanding of the design problem improves, assists in identifying conflicts in the design requirements. Additionally, the hierarchical set-up allows the embedding of multiple fitness functions into the genetic algorithm, each relevant to a specific level. This supports an integrated multi-level, multi-disciplinary approach. The HEAD system promotes a collaborative relationship between human creativity and the computer capability. The design schema component, as the input to the procedural algorithms, enables the encoding of certain aspects of the designer's subjective creativity. By focusing on finding solutions for the relevant sub-problems at the appropriate levels of detail, the hierarchical nature of the system assist in the design decision-making process.