Steady state and transient dynamometer vehicle emission measurements using a DiSC

Analysis of the particulate size and number concentration emissions from a fleet of inner city medium duty CNG buses was conducted using the newly available Diffusion Size Classifier in comparison with more traditional SMPS's and CPC's. Studies were conducted at both steady state and transient driving modes on a vehicle dynamometer utilising a CVS dilution system. Comparative analysis of the results showed that the DiSC provided equivalent information during steady state conditions and was able to provide additional information during transient conditions, namely, the modal diameter of the particle size distribution.

Development of gas sensing technology for ground and airborne applications powered by solar energy : methodology and experimental results

Monitoring gases for environmental, industrial and agricultural fields is a demanding task that requires long periods of observation, large quantity of sensors, data management, high temporal and spatial resolution, long term stability, recalibration procedures, computational resources, and energy availability. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) are currently representing the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialised gas sensing systems, and offer the possibility of geo-located and time stamp samples. However, these technologies are not fully functional for scientific and commercial applications as their development and availability is limited by a number of factors: the cost of sensors required to cover large areas, their stability over long periods, their power consumption, and the weight of the system to be used on small UAVs. Energy availability is a serious challenge when WSN are deployed in remote areas with difficult access to the grid, while small UAVs are limited by the energy in their reservoir tank or batteries. Another important challenge is the management of data produced by the sensor nodes, requiring large amount of resources to be stored, analysed and displayed after long periods of operation. In response to these challenges, this research proposes the following solutions aiming to improve the availability and development of these technologies for gas sensing monitoring: first, the integration of WSNs and UAVs for environmental gas sensing in order to monitor large volumes at ground and aerial levels with a minimum of sensor nodes for an effective 3D monitoring; second, the use of solar energy as a main power source to allow continuous monitoring; and lastly, the creation of a data management platform to store, analyse and share the information with operators and external users. The principal outcomes of this research are the creation of a gas sensing system suitable for monitoring any kind of gas, which has been installed and tested on CH4 and CO2 in a sensor network (WSN) and on a UAV. The use of the same gas sensing system in a WSN and a UAV reduces significantly the complexity and cost of the application as it allows: a) the standardisation of the signal acquisition and data processing, thereby reducing the required computational resources; b) the standardisation of calibration and operational procedures, reducing systematic errors and complexity; c) the reduction of the weight and energy consumption, leading to an improved power management and weight balance in the case of UAVs; d) the simplification of the sensor node architecture, which is easily replicated in all the nodes. I evaluated two different sensor modules by laboratory, bench, and field tests: a non-dispersive infrared module (NDIR) and a metal-oxide resistive nano-sensor module (MOX nano-sensor). The tests revealed advantages and disadvantages of the two modules when used for static nodes at the ground level and mobile nodes on-board a UAV. Commercial NDIR modules for CO2 have been successfully tested and evaluated in the WSN and on board of the UAV. Their advantage is the precision and stability, but their application is limited to a few gases. The advantages of the MOX nano-sensors are the small size, low weight, low power consumption and their sensitivity to a broad range of gases. However, selectivity is still a concern that needs to be addressed with further studies. An electronic board to interface sensors in a large range of resistivity was successfully designed, created and adapted to operate on ground nodes and on-board UAV. The WSN and UAV created were powered with solar energy in order to facilitate outdoor deployment, data collection and continuous monitoring over large and remote volumes. The gas sensing, solar power, transmission and data management systems of the WSN and UAV were fully evaluated by laboratory, bench and field testing. The methodology created to design, developed, integrate and test these systems was extensively described and experimentally validated. The sampling and transmission capabilities of the WSN and UAV were successfully tested in an emulated mission involving the detection and measurement of CO2 concentrations in a field coming from a contaminant source; the data collected during the mission was transmitted in real time to a central node for data analysis and 3D mapping of the target gas. The major outcome of this research is the accomplishment of the first flight mission, never reported before in the literature, of a solar powered UAV equipped with a CO2 sensing system in conjunction with a network of ground sensor nodes for an effective 3D monitoring of the target gas. A data management platform was created using an external internet server, which manages, stores, and shares the data collected in two web pages, showing statistics and static graph images for internal and external users as requested. The system was bench tested with real data produced by the sensor nodes and the architecture of the platform was widely described and illustrated in order to provide guidance and support on how to replicate the system. In conclusion, the overall results of the project provide guidance on how to create a gas sensing system integrating WSNs and UAVs, how to power the system with solar energy and manage the data produced by the sensor nodes. This system can be used in a wide range of outdoor applications, especially in agriculture, bushfires, mining studies, zoology, and botanical studies opening the way to an ubiquitous low cost environmental monitoring, which may help to decrease our carbon footprint and to improve the health of the planet.

On-road rapid identification of high-polluting transport buses

Exhaust emissions from motor vehicles vary widely and depend on factors such as engine operating conditions, fuel, age, mileage and service history. A method has been devised to rapidly identify high-polluting vehicles as they travel on the road. The method is able to monitor emissions from a large number of vehicles in a short time and avoids the need to conduct expensive and time consuming tests on chassis dynamometers. A sample of the exhaust plume is captured as each vehicle passes a roadside monitoring station and the pollutant emission factors are calculated from the measured concentrations using carbon dioxide as a tracer. Although, similar methods have been used to monitor soot and gaseous mass emissions, to-date it has not been used to monitor particle number emissions from a large fleet of vehicles. This is particularly important as epidemiological studies have shown that particle number concentration is an important parameter in determining adverse health effects. The method was applied to measurements of particle number emissions from individual buses in the Brisbane City Council diesel fleet operating on the South-East Busway. Results indicate that the particle number emission factors are gamma- distributed, with a high proportion of the emissions being emitted by a small percentage of the buses. Although most of the high-emitters are the oldest buses in the fleet, there are clear exceptions, with some newer buses emitting as much. We attribute this to their recent service history, particularly pertaining to improper tuning of the engines. We recommend that a targeted correction program would be a highly effective measure in mitigating urban environmental pollution.

A regional interpretation of rules and good practice for greenhouse accounting : Northern Australian savanna systems

Land-use change, particularly clearing of forests for agriculture, has contributed significantly to the observed rise in atmospheric carbon dioxide concentration. Concern about the impacts on climate has led to efforts to monitor and curtail the rapid increase in concentrations of carbon dioxide and other greenhouse gases in the atmosphere. Internationally, much of the current focus is on the Kyoto Protocol to the United Nations Framework Convention on Climate Change (UNFCCC). Although electing to not ratify the Protocol, Australia, as a party to the UNFCCC, reports on national greenhouse gas emissions, trends in emissions and abatement measures. In this paper we review the complex accounting rules for human activities affecting greenhouse gas fluxes in the terrestrial biosphere and explore implications and potential opportunities for managing carbon in the savanna ecosystems of northern Australia. Savannas in Australia are managed for grazing as well as for cultural and environmental values against a background of extreme climate variability and disturbance, notably fire. Methane from livestock and non-CO2 emissions from burning are important components of the total greenhouse gas emissions associated with management of savannas. International developments in carbon accounting for the terrestrial biosphere bring a requirement for better attribution of change in carbon stocks and more detailed and spatially explicit data on such characteristics of savanna ecosystems as fire regimes, production and type of fuel for burning, drivers of woody encroachment, rates of woody regrowth, stocking rates and grazing impacts. The benefits of improved biophysical information and of understanding the impacts on ecosystem function of natural factors and management options will extend beyond greenhouse accounting to better land management for multiple objectives.

A runtime integrity monitoring framework for real-time relative positioning systems based on GPS and DSRC

This paper provides a three-layered framework to monitor the positioning performance requirements of Real-time Relative Positioning (RRP) systems of the Cooperative Intelligent Transport Systems (C-ITS) that support Cooperative Collision Warning (CCW) applications. These applications exploit state data of surrounding vehicles obtained solely from the Global Positioning System (GPS) and Dedicated Short-Range Communications (DSRC) units without using other sensors. To this end, the paper argues the need for the GPS/DSRC-based RRP systems to have an autonomous monitoring mechanism, since the operation of CCW applications is meant to augment safety on roads. The advantages of autonomous integrity monitoring are essential and integral to any safety-of-life system. The autonomous integrity monitoring framework proposed necessitates the RRP systems to detect/predict the unavailability of their sub-systems and of the integrity monitoring module itself, and, if available, to account for effects of data link delays and breakages of DSRC links, as well as of faulty measurement sources of GPS and/or integrated augmentation positioning systems, before the information used for safety warnings/alarms becomes unavailable, unreliable, inaccurate or misleading. Hence, a monitoring framework using a tight integration and correlation approach is proposed for instantaneous reliability assessment of the RRP systems. Ultimately, using the proposed framework, the RRP systems will provide timely alerts to users when the RRP solutions cannot be trusted or used for the intended operation.

Quality assurance of aerial applications of larvicides for mosquito control : effects of granule and catch tray size on field monitoring programs

Aerial applications of granular insecticides are preferable because they can effectively penetrate vegetation, there is less drift, and no loss of product due to evaporation. We aimed to 1) assess the field efficacy ofVectoBac G to control Aedes vigilax (Skuse) in saltmarsh pools, 2) develop a stochastic-modeling procedure to monitor application quality, and 3) assess the distribution of VectoBac G after an aerial application. Because ground-based studies with Ae. vigilax immatures found that VectoBac G provided effective control below the recommended label rate of 7 kg/ha, we trialed a nominated aerial rate of 5 kg/ha as a case study. Our distribution pattern modeling method indicated that the variability in the number of VectoBac G particles captured in catch-trays was greater than expected for 5 kg/ha and that the widely accepted contour mapping approach to visualize the deposition pattern provided spurious results and therefore was not statistically appropriate. Based on the results of distribution pattern modeling, we calculated the catch tray size required to analyze the distribution of aerially applied granular formulations. The minimum catch tray size for products with large granules was 4 m2 for Altosid pellets and 2 m2 for VectoBac G. In contrast, the minimum catch-tray size for Altosid XRG, Aquabac G, and Altosand, with smaller granule sizes, was 1 m2. Little gain in precision would be made by increasing the catch-tray size further, when the increased workload and infrastructure is considered. Our improved methods for monitoring the distribution pattern of aerially applied granular insecticides can be adapted for use by both public health and agricultural contractors.

Government procurement contracts and minimum labour standards enforcement: Rhetoric, duplication and distraction?

Government contracts for services typically include terms requiring contractors to comply with minimum labour standards laws. Procurement contract clauses specify reporting procedures and sanctions for non-compliance, implying that government contracting agencies will monitor and enforce minimum labour standards within contract performance management. In this article, the case of school cleaners employed under New South Wales government contracts between 2010 and 2011 is the vehicle for exploring the effectiveness of these protective clauses. We find that the inclusion of these protective clauses in procurement contracts is unnecessary in the Australian context, and any expectations that government contracting agencies will monitor and enforce labour standards are misleading. At best, the clauses are rhetoric, and at worst, they are a distraction for parties with enforcement powers.

The automation of radiotherapy treatment planning assessment

Aim The assessment of treatment plans is an important component in the education of radiation therapists. The establishment of a grade for a plan is currently based on subjective assessment of a range of criteria. The automation of assessment could provide a number of advantages including faster feedback, reduced chance of human error, and simpler aggregation of past results. Method A collection of treatments planned by a cohort of 27 second year radiation therapy students were selected for quantitative evaluation. Treatment sites included the bladder, cervix, larynx, parotid and prostate, although only the larynx plans had been assessed in detail. The plans were designed with the Pinnacle system and exported using the DICOM framework. Assessment criteria included beam arrangement optimisation, volume contouring, target dose coverage and homogeneity, and organ-at-risk sparing. The in-house Treatment and Dose Assessor (TADA) software1 was evaluated for suitability in assisting with the quantitative assessment of these plans. Dose volume data were exported in per-student and per-structure data tables, along with beam complexity metrics, dose volume histograms, and reports on naming conventions. Results The treatment plans were exported and processed using TADA, with the processing of all 27 plans for each treatment site taking less than two minutes. Naming conventions were successfully checked against a reference protocol. Significant variations between student plans were found. Correlation with assessment feedback was established for the larynx plans. Conclusion The data generated could be used to inform the selection of future assessment criteria, monitor student development, and provide useful feedback to the students. The provision of objective, quantitative evaluations of plan quality would be a valuable addition to not only radiotherapy education programmes but also for staff development and potentially credentialing methods. New functionality within TADA developed for this work could be applied clinically to, for example, evaluate protocol compliance.

Combining passive sampling and toxicity testing for evaluation of mixtures of polar organic chemicals in sewage treatment plant effluent

Effluent from sewage treatment plants has been associated with a range of pollutant effects. Depending on the influent composition and treatment processes the effluent may contain a myriad of different chemicals which makes monitoring very complex. In this study we aimed to monitor relatively polar organic pollutant mixtures using a combination of passive sampling techniques and a set of biochemistry based assays covering acute bacterial toxicity (Microtox™), phytotoxicity (Max-I-PAM assay) and genotoxicity (umuC assay). The study showed that all of the assays were able to detect effects in the samples and allowed a comparison of the two plants as well as a comparison between the two sampling periods. Distinct improvements in water quality were observed in one of the plants as result of an upgrade to a UV disinfection system, which improved from 24× sample enrichment required to induce a 50% response in the Microtox™ assay to 84×, from 30× sample enrichment to induce a 50% reduction in photosynthetic yield to 125×, and the genotoxicity observed in the first sampling period was eliminated. Thus we propose that biochemical assay techniques in combination with time integrated passive sampling can substantially contribute to the monitoring of polar organic toxicants in STP effluents.

European aspects of standard setting in occupational hygiene and medicine

Occupational standards concerning the allowable concentrations of chemical compounds in the ambient air of workplaces have been established in several countries at national levels. With the integration of the European Union, a need exists for establishing harmonized Occupational Exposure Limits. For analytical developments, it is apparent that methods for speciation or fractionation of carcinogenic metal compounds will be of increasing practical importance for standard setting. Criteria of applicability under field conditions, cost-effectiveness, and robustness are practical driving forces for new developments. When the European Union issued a list of 62 chemical substances with Occupational Exposure Limits in 2000, 25 substances received a 'skin' notation. The latter indicates that toxicologically significant amounts may be taken up via the skin. Similar notations exist on national levels. For such substances, monitoring concentrations in ambient air will not be sufficient; biological monitoring strategies will gain further importance in the medical surveillance of workers who are exposed to such compounds. Proceedings in establishing legal frameworks for a biological monitoring of chemical exposures within Europe are paralleled by scientific advances in this field. A new aspect is the possibility of a differential adduct monitoring, using blood proteins of different half-life or lifespan. This technique allows differentiation between long-term mean exposure to reactive chemicals and short-term episodes, for example, by accidental overexposure. For further analytical developments, the following issues have been addressed as being particularly important: New dose monitoring strategies, sensitive and reliable methods for detection of DNA adducts, cytogenetic parameters in biological monitoring, methods to monitor exposure to sensitizing chemicals, and parameters for individual susceptibilities to chemical toxicants.

Meta-analysis of microarray data identifies GAS6 expression as an independent predictor of poor survival in ovarian cancer

Seeking new biomarkers for epithelial ovarian cancer, the fifth most common cause of death from all cancers in women and the leading cause of death from gynaecological malignancies, we performed a meta-analysis of three independent studies and compared the results in regard to clinicopathological parameters. This analysis revealed that GAS6 was highly expressed in ovarian cancer and therefore was selected as our candidate of choice. GAS6 encodes a secreted protein involved in physiological processes including cell proliferation, chemotaxis, and cell survival. We performed immunohistochemistry on various ovarian cancer tissues and found that GAS6 expression was elevated in tumour tissue samples compared to healthy control samples (P < 0.0001). In addition, GAS6 expression was also higher in tumours from patients with residual disease compared to those without. Our data propose GAS6 as an independent predictor of poor survival, suggesting GAS6, both on the mRNA and on the protein level, as a potential biomarker for ovarian cancer. In clinical practice, the staining of a tumour biopsy for GAS6 may be useful to assess cancer prognosis and/or to monitor disease progression.

Dalby Shopping Precinct Survey Report : Consumer Attitudes towards Proposed Extended Trading Hours at Dalby

Data was collected to measure shopper’s attitudes toward the proposed Sunday and limited public holiday trading in Dalby. Survey questionnaires were conducted between 29th August to 31st August at Coles Dalby and Dalby Shoppingtown Plaza. In total, 150 respondents participated in the survey. Overall, the findings suggest that most respondents, especially males, couples with children, fulltime workers and those under the age of 49 years, embrace the proposed Sunday and limited holiday trading in Dalby. While there are concerns over increasing competition for smaller retailers who already trade on Sundays, a majority of respondents indicated it would suit their lifestyle, be convenient, provide more jobs, increase trade for smaller retailers within the area, reduce queues and congestion observed on Saturdays. The majority of those shoppers that indicated they currently did some shopping on a Sunday reported they would continue to support smaller retailers who currently trade on Sundays and some public holidays, if changes came about. Those opposed to changes to trading hours indicated a belief that existing trading hours were sufficient. Most people indicated the proposed extension of trading hours would not harm the community or have a negative, detrimental effect on themselves or their family. The main findings presented in the report are as follows: - 96.8% of respondents surveyed reported to be local, permanent residents of Dalby. - Residents of Dalby visited shopping centres and stores on average 2.8 times per week. This frequency is proportionately higher than the average Australian shopping behaviour at 2.5 times per week (Roy Morgan Supermarket Monitor). - It was determined that weekday evenings (after 5 pm) were the busiest times for shopping, with Saturday the next most popular day to shop. - 68% of respondents support the proposal of the extended trading hours at supermarkets, department stores and the shopping centre in Dalby, 26% oppose and 6% are unsure. - 90% of the respondents agreed that residents of Dalby should be allowed the same choice as other regional towns and cities in supporting/opposing changes to trading hours. The remaining 10% expressed a disagreement. - A larger percentage of males supported the proposal for Sunday and limited holiday trading. Of all the males surveyed, 80% were in support, 15% were opposed and 5% unsure. 60% of female respondents support the proposal, while 33% oppose it and 5% were unsure. - The highest percentage of support exists in fulltime workers with 90% of those respondents supporting the proposal. - In contrast, the lowest percentage of support was found in the non-working (retired/unemployed) respondents, where 67% opposed the application. - It was noted that 71% of respondents employed casually also indicated opposition against proposed changes. Further questioning identified an underlying concern from casually employed persons that Sunday trade would force them onto Sunday work rosters. - 92% of shared households expressed support for Sunday and limited public holiday trading, while 83% of both couples with children and single parent with children at home also supported the application. - 72% of the respondents often find it necessary to do some grocery shopping in Dalby on a Sunday. 76% of shoppers who indicated they already undertook some shopping on Sunday, indicated would continue to shop and support smaller retailers. - Of the respondents surveyed, 44% have travelled outside of Dalby on a Sunday to shop. This indicates that such residents find it necessary to undertake some shopping on a Sunday and in order to do so, drive an hour to Toowoomba in order to access a range of retailers. - The most cited reasons for supporting Sunday and limited public holiday trade were; ‘More choice about when I shop and that is convenient’ (69%), ‘Sunday trade will create job opportunities’ (71%), ‘Sunday trade will be helpful when preparing school lunches and getting ready for the working week’ (62%), and ‘Sunday trade will reduce shopping congestion during peak shopping periods’ (62%) - The most cited reasons for opposing the proposed changes are that ‘Sunday trade may increase competition for small retailers who already trade on Sunday’ (41%), ‘Shops are already open 6 days a week which is enough’ (31%), and ‘Sunday is a day of rest or a religious day and shopping should not be allowed’ (23%). - 97% of respondents indicated they would not change their sporting or social commitment if changes to trading hours were implemented.

Intravenous injection of leconotide, an omega conotoxin : synergistic antihyperalgesic effects with morphine in a rat model of bone cancer pain

Objective.  Leconotide (CVID, AM336, CNSB004) is an omega conopeptide similar to ziconotide, which blocks voltage sensitive calcium channels. However, unlike ziconotide, which must be administered intrathecally, leconotide can be given intravenously because it is less toxic. This study investigated the antihyperalgesic potency of leconotide given intravenously alone and in combinations with morphine-administered intraperitoneally, in a rat model of bone cancer pain. Design.  Syngeneic rat prostate cancer cells AT3B-1 were injected into one tibia of male Wistar rats. The tumor expanded within the bone causing hyperalgesia to heat applied to the ipsilateral hind paw. Measurements were made of the maximum dose (MD) of morphine and leconotide given alone and in combinations that caused no effect in an open-field activity monitor, rotarod, and blood pressure and heart rate measurements. Paw withdrawal thresholds from noxious heat were measured. Dose response curves for morphine (0.312–5.0 mg/kg intraperitoneal) and leconotide (0.002–200 µg/kg intravenous) given alone were plotted and responses compared with those caused by morphine and leconotide in combinations. Results.  Leconotide caused minimal antihyperalgesic effects when administered alone. Morphine given alone intraperitoneally caused dose-related antihyperalgesic effects (ED50 = 2.40 ± 1.24 mg/kg), which were increased by coadministration of leconotide 20 µg/kg (morphine ED50 = 0.16 ± 1.30 mg/kg); 0.2 µg/kg (morphine ED50 = 0.39 ± 1.27 mg/kg); and 0.02 µg/kg (morphine ED50 = 1.24 ± 1.30 mg/kg). Conclusions.  Leconotide caused a significant increase in reversal by morphine of the bone cancer-induced hyperalgesia without increasing the side effect profile of either drug. Clinical Implication.  Translation into clinical practice of the method of analgesia described here will improve the quantity and quality of analgesia in patients with bone metastases. The use of an ordinary parenteral route for administration of the calcium channel blocker (leconotide) at low dose opens up the technique to large numbers of patients who could not have an intrathecal catheter for drug administration. Furthermore, the potentiating synergistic effect with morphine on hyperalgesia without increased side effects will lead to greater analgesia with improved quality of life.

Mt Isa Shopping Precinct Survey Report : Consumer Attitudes towards Proposed Extended Trading Hours at Mt Isa

Data was collected to measure shopper’s attitudes toward the proposed Sunday and limited public holiday trading in Mt Isa. Survey questionnaires were conducted between 15th August to 17th August at Kmart Plaza, Woolworths, Miles St. and Mt Isa Plaza. In total, 300 respondents participated in the survey. Overall, the findings suggest that most respondents, especially males, couples with children and fulltime workers, embrace the proposed Sunday and limited holiday trading in Mt Isa. While there are concerns over increasing competition for smaller retailers who already trade on Sundays, a majority of respondents indicated it would suit their lifestyle, be convenient, provide more jobs, increase trade for smaller retailers within the area, reduce queues and congestion, and offer a less expensive grocery shopping. The majority of those shoppers that indicated they currently did some shopping on a Sunday reported they would continue to support smaller retailers who currently trade on Sundays and some public holidays, if changes came about. Those opposed to changes to trading hours also indicated a belief that existing trading hours were sufficient. Most people indicated the proposed extension of trading hours would not harm the community or have a negative, detrimental effect on themselves or their family. The main findings presented in the report are as follows: - 96% of respondents surveyed reported to be local, permanent residents of Mt Isa. - Residents of Mt Isa visited shopping centres and stores on average 2.4 times per week. This mirrors the average Australian shopping behaviour at 2.5 times per week (Roy Morgan Supermarket Monitor) - It was determined that Saturday was the busiest day for shopping with a majority of respondents indicating they visited stores on that day of the week. - 71% of respondents support the proposal of extended trading hours at shopping centres in Mt Isa, 25% oppose and 4% are unsure. - 87% of the respondents agreed that residents of Mt Isa should be allowed the same choice as other regional towns and cities in supporting/opposing changes to trading hours. The remaining 13% expressed a disagreement. - A larger percentage of males supported the proposal for Sunday and limited holiday trading. Of all the males surveyed, 81% were in support, 17% were opposed and 2% unsure. By contrast, 64% of female respondents support the proposal, while 31% oppose it and 5% are unsure. - The highest percentage of support exists in fulltime workers with 85% of those respondents supporting the proposal. In contrast, the lowest percentage of support was found in the non-working respondents, where 62% opposed the application. - 78% of couples living with children at home expressed support for Sunday and limited public holiday trading, while 60% of couples without children also supported the application. - Of the respondents surveyed, virtually none (less than 1%) have travelled outside of Mt Isa on a Sunday to shop. This indicates that due to the remote and isolated location of this town, residents do not have the option to travel reasonable distances in order to access a range of retailers. - 70% of the respondents often find it necessary to do some grocery shopping in Mt Isa on a Sunday. - Convenience is cited as the major reason for support (79%) followed by lifestyle (75%). - The most cited reasons for supporting ‘it would be convenient’ (81%), ‘It may create more jobs’ (77%), ‘It may reduce congestion during busy shopping periods’ (74%, and ‘It would make it easier for working families with kids’ (74%). - The most cited reasons for opposing the proposed changes are that ‘It will disadvantage smaller businesses’ (44%), ‘It is unnecessary’ (29%). - 72% of shoppers who indicated they already undertook some shopping on Sunday, indicated would continue to shop and support smaller retailers. - 98% of respondents indicated they would not change their sporting or social commitment if changes to trading hours were implemented.

Supporting residents’ expression of sexuality : the initial construction of a sexuality assessment tool for residential aged care facilities

Background: Sexuality is a key component of quality of life and well-being and a need to express one’s sexuality continues into old age. Staff and families in residential aged care facilities often find expressions of sexuality by residents, particularly those living with dementia, challenging and facilities often struggle to address individuals’ needs in this area. This paper describes the development of an assessment tool which enables residential aged care facilities to identify how supportive their organisation is of all residents’ expression of their sexuality, and thereby improve where required. Methods: Multi-phase design using qualitative methods and a Delphi technique. Tool items were derived from the literature and verified by qualitative interviews with aged care facility staff, residents and families. The final item pool was confirmed via a reactive Delphi process. Results: A final item pool of sixty-nine items grouped into seven key areas allows facilities to score their compliance with the areas identified as being supportive of older people’s expression of their sexuality in a residential aged care environment. Conclusions: The sexuality assessment tool (SexAT) guides practice to support the normalization of sexuality in aged care homes and assists facilities to identify where enhancements to the environment, policies, procedures and practices, information and education/training are required. The tool also enables facilities to monitor initiatives in these areas over time.