Characterization of VOCs from LPG and unleaded petroleum fuelled passenger cars

The study monitored the emissions of volatile organic compounds (VOCs) from the exhaust of cars fuelled by liquefied petroleum gas (LPG) and unleaded petrol (ULP). Six cars, four fuelled by LPG and two by ULP, were tested on a chassis dynamometer at two different cruising modes of operation (60 km h−1 and 80 km h−1) and idle. A total of 33 VOCs were identified in the exhaust of both types of fuels by the use of GC/MS. Due to the complexity of the dataset, Multi Criteria Decision Making (MCDM) software PROMETHEE and GAIA was used to rank the least polluting mode and fuel. The 60 km h−1 driving speed was identified as the cleaner mode of driving as was LPG fuel. The Ozone Formation Potential (OFP) of the VOCs was also calculated by using the incremental reactivity scale. Priority VOCs leading to ozone formation were identified according to the three incremental reactivity scales: MIR, MOIR and EBIR. PROMETHEE was applied to assess the most preferred scale of reactivity for predicting ozone formation potential under different scenarios. The results enhance the understanding of the environmental value of using LPG to power passenger cars.

Quantification of motor vehicle emission factors from on road measurements

Assessment and prediction of the impact of vehicular traffic emissions on air quality and exposure levels requires knowledge of vehicle emission factors. The aim of this study was quantification of emission factors from an on road, over twelve months measurement program conducted at two sites in Brisbane: 1) freeway type (free flowing traffic at about 100 km/h, fleet dominated by small passenger cars - Tora St); and 2) urban busy road with stop/start traffic mode, fleet comprising a significant fraction of heavy duty vehicles - Ipswich Rd. A physical model linking concentrations measured at the road for specific meteorological conditions with motor vehicle emission factors was applied for data analyses. The focus of the study was on submicrometer particles; however the measurements also included supermicrometer particles, PM2.5, carbon monoxide, sulfur dioxide, oxides of nitrogen. The results of the study are summarised in this paper. In particular, the emission factors for submicrometer particles were 6.08 x 1013 and 5.15 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd respectively and for supermicrometer particles for Tora St, 1.48 x 109 particles per vehicle-1 km-1. Emission factors of diesel vehicles at both sites were about an order of magnitude higher than emissions from gasoline powered vehicles. For submicrometer particles and gasoline vehicles the emission factors were 6.08 x 1013 and 4.34 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively, and for diesel vehicles were 5.35 x 1014 and 2.03 x 1014 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively. For supermicrometer particles at Tora St the emission factors were 2.59 x 109 and 1.53 x 1012 particles per vehicle-1 km-1, for gasoline and diesel vehicles, respectively.

Increase in particle number emissions from motor vehicles due to interruption of steady traffic flow

We assess the increase in particle number emissions from motor vehicles driving at steady speed when forced to stop and accelerate from rest. Considering the example of a signalized pedestrian crossing on a two-way single-lane urban road, we use a complex line source method to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses and show that the total emissions during a red light is significantly higher than during the time when the light remains green. Replacing two cars with one bus increased the emissions by over an order of magnitude. Considering these large differences, we conclude that the importance attached to particle number emissions in traffic management policies be reassessed in the future.

The influence of MTV

MTV has had a key impact on advertising, not only from the point of view that commercials are aired during its programmes, but also because videos themselves can be viewed as advertisements. Music videos came about as a result of the music industry being in a recession during the early eighties. Initially MTV’s incentive to develop music television was advertiser led (Goodwin, 1992, p.38). One needs to remember that television is in the business to make money - not to entertain (Allen, 1992); and that viewers are in effect sold to the advertisers (White, 1992), and MTV is an influential media forces on their targets audience of between the ages twelve and thirty-four, with a median age of twenty-three (Englis et al., 1994). The reason why MTV is such an effective advertising medium, is that it utilises music, mood, visual elements, popular culture and the socialising effect of television, to sell its message in a susceptible/ passive manner. Its primary goal is to promote the artist or band performing in the video clip, so that consumers will purchase their CDs, as well as other band related products. But more often than not, the video clip sells much more than just that. Lifestyles, fashion, cosmetics, cars, consumer and social behaviour are all promoted in an unsuspecting manner. Advertisers, as a result, have looked to MTV for ideas on how to better communicate with the youth market; adopting similar styles to get their message across. The following looks at how and why, the fusion of MTV and advertising works so well together by considering past research.

Enhancing road safety for young drivers : how Graduate Driver Licensing initiatives can complement "anti-hooning" legislation

Street racing and associated (hooning) behaviours have attracted increasing concern in recent years. While New Zealand and all Australian jurisdictions have introduced “antihooning” legislation and allocated significant police resources to managing the problem, there is limited evidence of the road safety implications of hooning. However, international and Australian data suggests that drivers charged with a hooning offence tend to be young males who are accompanied by one or more peers, and hooning-related crashes tend to occur at night. In this regard, there is considerable evidence that drivers under the age of 25 are over-represented in crash statistics, and are particularly vulnerable soon after obtaining a Provisional licence, when driving at night, and when carrying peer-aged passengers. The similarity between the nature of hooning offenders, offences and crashes, and road safety risks for young drivers in general, suggests that hooning is an issue that may be viewed as part of the broader young driver problem. Many jurisdictions have recently implemented a range of evidence-based strategies to address young driver road safety, and this paper will present Queensland crash and offence data to highlight the potential benefit of Graduated Driver Licensing initiatives, such as night driving restrictions and peer-aged passenger restrictions, to related road safety issues, including hooning. An understanding of potential flow-on effects is important for evaluations of anti-hooning legislation and Graduated Driver Licensing programs, and may have implications for future law enforcement resource allocation and policy development.

Non-motorized public transport : a global review and analysis of trends and issues

Over recent decades there has been growing interest in the role of non-motorized modes in the overall transport system (especially walking and cycling for private purposes) and many government initiatives have been taken to encourage these active modes. However there has been relatively little research attention given to the paid form of non-motorized travel which can be called non-motorized public transport (NMPT). This involves cycle-powered vehicles which can carry several passengers (plus the driver) and a small amount of goods; and which provide flexible hail-and-ride services. Effectively they are non-motorized taxis. Common forms include cycle-rickshaw (Bangladesh, India), becak (Indonesia), cyclos (Vietnam, Cambodia), bicitaxi (Columbia, Cuba), velo-taxi (Germany, Netherland), and pedicabs (UK, Japan, USA). --------- The popularity of NMPT is widespread in developing countries, where it caters for a wide range of mobility needs. For instance in Dhaka, Bangladesh, rickshaws are the preferred mode for non-walk trips and have a higher mode share than cars or buses. Factors that underlie the continued existence and popularity of NMPT in many developing countries include positive contribution to social equity, micro-macro economic significance, employment creation, and suitability for narrow and crowded streets. Although top speeds are lower than motorized modes, NMPT is competitive and cost-effective for short distance door-to-door trips that make up the bulk of travel in many developing cities. In addition, NMPT is often the preferred mode for vulnerable groups such as females, children and elderly people. NMPT is more prominent in developing countries but its popularity and significance is also gradually increasing in several developed countries of Asia, Europe and parts of North America, where there is a trend for the NMPT usage pattern to broaden from tourism to public transport. This shift is due to a number of factors including the eco-sustainable nature of NMPT; its operating flexibility (such as in areas where motorized vehicle access is restricted or discouraged through pricing); and the dynamics that it adds to the urban fabric. Whereas NMPT may have been seen as a “dying” mode, in many cities it is maintaining or increasing its significance and with potential for further growth. --------- This paper will examine and analyze global trends in NMPT incorporating both developing and developed country contexts and issues such as usage patterns; NMPT policy and management practices; technological development; and operational integration of NMPT into the overall transport system. It will look at how NMPT policies, practices and usage have changed over time and the differing trends in developing and developed countries. In particular, it will use Dhaka, Bangladesh as a case study in recognition of its standing as the major NMPT city in the world. The aim is to highlight NMPT issues and trends and their significance for shaping future policy towards NMPT in developing and developed countries. The paper will be of interest to transport planners, traffic engineers, urban and regional planners, environmentalists, economists and policy makers.

Prosecution history estoppel in the UK?

The doctrine of 'prosecution history estoppel' (PH estoppel) as developed in the United States has strong intuitive appeal, especially when applied to counterbalance a related patent law principle, the doctrine of equivalents. The doctrines are receiving increasing attention in US patent decisions, to the point where one patent litigator recently compared them to "two cars that keep bumping fenders. They are frequently returned to the shop for repairs". Could PH estoppel find its way into UK patent law? This article briefly examines the doctrine, its evolution in the US and the problems associated with importing the doctrine into the UK. As the EU legislation stands, Article 69 and the Protocol to the European Patent Convention (EPC) pose serious obstacles to using the doctrine directly in claim construction. However there appears to be some scope to apply the doctrine as a limited form of defence in infringement actions.

Flexible high-power multi DC-DC converters for train systems

This thesis reports on the investigations, simulations and analyses of novel power electronics topologies and control strategies. The research is financed by an Australian Research Council (ARC) Linkage (07-09) grant. Therefore, in addition to developing original research and contributing to the available knowledge of power electronics, it also contributes to the design of a DC-DC converter for specific application to the auxiliary power supply in electric trains. Specifically, in this regard, it contributes to the design of a 7.5 kW DC-DC converter for the industrial partner (Schaffler and Associates Ltd) who supported this project. As the thesis is formatted as a ‘thesis by publication’, the contents are organized around published papers. The research has resulted in eleven papers, including seven peer reviewed and published conference papers, one published journal paper, two journal papers accepted for publication and one submitted journal paper (provisionally accepted subject to few changes). In this research, several novel DC-DC converter topologies are introduced, analysed, and tested. The similarity of all of the topologies devised lies in their ‘current circulating’ switching state, which allows them to store some energy in the inductor, as extra inductor current. The stored energy may be applied to enhance the performance of the converter in the occurrence of load current or input voltage disturbances. In addition, when there is an alternating load current, the ability to store energy allows the converter to perform satisfactorily despite frequently and highly varying load current. In this research, the capability of current storage has been utilised to design topologies for specific applications, and the enhancement of the performance of the considered applications has been illustrated. The simplest DC-DC converter topology, which has a ‘current circulating’ switching state, is the Positive Buck-Boost (PBB) converter (also known as the non-inverting Buck-Boost converter). Usually, the topology of the PBB converter is operating as a Buck or a Boost converter in applications with widely varying input voltage or output reference voltage. For example, in electric railways (the application of our industrial partner), the overhead line voltage alternates from 1000VDC to 500VDC and the required regulated voltage is 600VDC. In the course of this research, our industrial partner (Schaffler and Associates Ltd) industrialized a PBB converter–the ‘Mudo converter’–operating at 7.5 kW. Programming the onboard DSP and testing the PBB converter in experimental and nominal power and voltage was part of this research program. In the earlier stages of this research, the advantages and drawbacks of utilization of the ‘current circulating’ switching state in the positive Buck-Boost converter were investigated. In brief, the advantages were found to be robustness against input voltage and current load disturbances, and the drawback was extra conduction and switching loss. Although the robustness against disturbances is desirable for many applications, the price of energy loss must be minimized to attract attention to the utilization of the PBB converter. In further stages of this research, two novel control strategies for different applications were devised to minimise the extra energy loss while the advantages of the positive Buck-Boost converter were fully utilized. The first strategy is Smart Load Controller (SLC) for applications with pre-knowledge or predictability of input voltage and/or load current disturbances. A convenient example of these applications is electric/hybrid cars where a master controller commands all changes in loads and voltage sources. Therefore, the master controller has a pre-knowledge of the load and input voltage disturbances so it can apply the SLC strategy to utilize robustness of the PBB converter. Another strategy aiming to minimise energy loss and maximise the robustness in the face of disturbance is developed to cover applications with unexpected disturbances. This strategy is named Dynamic Hysteresis Band (DHB), and is used to manipulate the hysteresis band height after occurrence of disturbance to reduce dynamics of the output voltage. When no disturbance has occurred, the PBB converter works with minimum inductor current and minimum energy loss. New topologies based on the PBB converter have been introduced to address input voltage disturbances for different onboard applications. The research shows that the performance of applications of symmetrical/asymmetrical multi-level diode-clamped inverters, DC-networks, and linear-assisted RF amplifiers may be enhanced by the utilization of topologies based on the PBB converter. Multi-level diode-clamped inverters have the problem of DC-link voltage balancing when the power factor of their load closes to unity. This research has shown that this problem may be solved with a suitable multi-output DC-DC converter supplying DClink capacitors. Furthermore, the multi-level diode-clamped inverters supplied with asymmetrical DC-link voltages may improve the quality of load voltage and reduce the level of Electromagnetic Interference (EMI). Mathematical analyses and experiments on supplying symmetrical and asymmetrical multi-level inverters by specifically designed multi-output DC-DC converters have been reported in two journal papers. Another application in which the system performance can be improved by utilization of the ‘current circulating’ switching state is linear-assisted RF amplifiers in communicational receivers. The concept of ‘linear-assisted’ is to divide the signal into two frequency domains: low frequency, which should be amplified by a switching circuit; and the high frequency domain, which should be amplified by a linear amplifier. The objective is to minimize the overall power loss. This research suggests using the current storage capacity of a PBB based converter to increase its bandwidth, and to increase the domain of the switching converter. The PBB converter addresses the industrial demand for a DC-DC converter for the application of auxiliary power supply of a typical electric train. However, after testing the industrial prototype of the PBB converter, there were some voltage and current spikes because of switching. To attenuate this problem without significantly increasing the switching loss, the idea of Active Gate Signalling (AGS) is presented. AGS suggests a smart gate driver that selectively controls the switching process to reduce voltage/current spikes, without unacceptable reduction in the efficiency of switching.

Top Gear, top journalism : three lessons for political journalists from the world's most popular TV show

This article examines the BBC program Top Gear, discussing why it has become one of the world’s most-watched TV programs, and how it has very successfully captivated an audience who might otherwise not be particularly interested in cars. The analysis of the show is here framed in the form of three ‘lessons’ for journalists, suggesting that some of the entertaining (and highly engaging) ways in which Top Gear presents information to its viewers could be usefully applied in the coverage of politics – a domain of knowledge which, like cars, many citizens find abstract or boring.

Novel car carrier design : prevention of falls from heights

This article reports the details of a research on novel design in the field of semitrailer sector and discuss design by hazard prevention techniques. The novel design made addresses occupational health and safety (OHS)concerns of fall from heights. The research includes a detailed survey of national data sources to examine the fatalities caused due to fall from heights in car carriers. The study investigates OHS recommendations in Australia for semitrailer sector. Often injuries are caused due to drivers working above the 1.5 meter height for loading, unloading of the cars, moving the decks up, down, strapping the cars, and slipperly. The new design is developed using latest computer aided design and engineeing (CAD, CAE), product data management (PDM), virtual design process (VDP). The new car carrier design excels in reducing the risks of injuries to drivers and new bench mark for OHS standards. The new design has all the decks operated with hydraulics and uses unique ratchet lock mechanism (fool proof design) and loading happens at a safe working height (below 1.5 meter). All the cars are strapped on the safe working height, and then car desks operated hydraulically to transfer them to the required position. This also includes the car on the prime mover, which shuttles across from one deck to other using hydraulic and rack-pinion mechanisms. The novel design car carrier solves the problem of falls from height: next step would be to transfer this technology across other similar effected sectors.

Announcement and legislation enactment improve children’s seating position in regional areas

New legislation requires all children 7 years and younger to use child-specific Australian Standards approved restraints suitable to their age and restricts seating young children in the front of cars. Observations of child seating position and restraint use were undertaken in Toowoomba and Rockhampton before the Queensland legislation was announced (T1), after the announcement but before it was enacted (T2) and after it came into force (T3). From T1 to T2, the percentage of children seated in the rear increased (69% to 75%), with a further increase from T2 to T3 (75% to 77%). This pattern was clear when there were one or two children in the car, but not when there were 3 or more. The effect on restraint use was more complex. After the announcement (T2) the percentage of children using adult seatbelts significantly increased regardless of the number of child passengers. However, once the legislation was enacted (T3) there was a significant increase in the percentage of children using child seats/boosters where there was one or two child passengers. Where there were three or more children in the vehicle there was little change in restraint choice between pre (T1) and post (T3) legislation.

Influence of iodine value on combustion and NOx emission characteristics of a DI diesel engine

Biodiesel is a renewable fuel that has been shown to reduce many exhaust emissions, except oxides of nitrogen (NOx), in diesel engine cars. This is of special concern in inner urban areas that are subject to strict environmental regulations, such as EURO norms. Also, the use of pure biodiesel (B100) is inhibited because of its higher NOx emissions compared to petroleum diesel fuel. The aim of this present work is to investigate the effect of the iodine value and cetane number of various biodiesel fuels obtained from different feed stocks on the combustion and NOx emission characteristics of a direct injection (DI) diesel engine. The biodiesel fuels were chosen from various feed stocks such as coconut, palm kernel, mahua (Madhuca indica), pongamia pinnata, jatropha curcas, rice bran, and sesame seed oils. The experimental results show an approximately linear relationship between iodine value and NOx emissions. The biodiesels obtained from coconut and palm kernel showed lower NOx levels than diesel, but other biodiesels showed an increase in NOx. It was observed that the nature of the fatty acids of the biodiesel fuels had a significant influence on the NOx emissions. Also, the cetane numbers of the biodiesel fuels are affected both premixed combustion and the combustion rate, which further affected the amount of NOx formation. It was concluded that NOx emissions are influenced by many parameters of biodiesel fuels, particularly the iodine value and cetane number.

The prevalence and characteristics of self-reported dangerous driving behaviours among a young cohort

Background: Young motorists engaging in anti-social and often dangerous driving manoeuvres (which is often referred to as “hooning” within Australia) is an increasing road safety problem. While anecdotal evidence suggests that such behaviour is positively linked with crash involvement, researchers have yet to examine whether younger drivers who deliberately break road rules and drive in an erratic manner (usually with peers) are in fact over represented in crash statistics. This paper outlines research that aimed to identify the characteristics of individuals most likely to engaging in hooning behaviours, as well as examine the frequency of such driving behaviours and if such activity is linked with self-reported crash involvement.---------- Methods: A total of 717 young drivers in Queensland voluntarily completed a questionnaire to investigate their driving behaviour and crash history.---------- Results: Quantitative analysis of the data revealed that almost half the sample reported engaging in some form of “hooning” behaviour at least once in their lifetime, although only 4% indicated heavy participation in the behaviour e.g., >50 times. Street racing was the most common activity reported by participants followed by “drifting” and then “burnouts”. Logistic regression analysis indicated that being younger and a male was predictive of reporting such anti-social driving behaviours, and importantly, a trend was identified between such behaviour and self-reported crash involvement.---------- Conclusions: This research provides preliminary evidence that younger male drivers are more likely to engage in dangerous driving behaviours, which ultimately may prove to increase their overall risk of becoming involved in a crash. This paper will further outline the study findings in regards to current enforcement efforts to deter such driving activity as well as provide direction for future research efforts in this area.---------- Research highlights: ► The self-reported driving behaviours of 717 younger Queensland drivers were examined to investigate the relationship between deliberately breaking road rules and self-reported crash involvement. ► Younger male drivers were most likely to engage in such aberrant driving behaviours and a trend was identified between such behaviour and self-reported crash involvement.

Property Agents and Motor Dealers Act : strike three

The Tourism, Racing and Fair Trading (Miscellaneous Provisions) Act 2002 (“the Act”) which was passed on 18 April 2002 contains a number of significant amendments relevant to the operation of the Property Agents and Motor Dealers Act 2000. The main changes relevant to property transactions are: (i) Changes to the process for appointment of a real estate agent and consolidation of the appointment forms; (ii) Additions to the disclosure obligation of agents and property developers; (iii) Simplification of the process for commencing the cooling off period; (iv) Alteration of the common law position concerning when the parties are bound by a contract; (v) Removal of the requirement for a seller’s signature on the warning statement to be witnessed; (vi) Retrospective amendment of s 170 of the Body Corporate and Community Management Act 1997; (vii) Inclusion of a new power to allow inspectors to enter the place of business of a licensee or a marketeer without consent and without a warrant; and (viii) Inclusion of a new power for inspectors to require documents to be produced by marketeers. The majority of the amendments are effective from the date of assent, 24 April 2002, however, some of the amendments do not commence until a date fixed by proclamation. No proclamation has been made at the time of writing (2 May 2002). Where the amendments have not commenced this will be noted in the article. Before providing clients with advice, practitioners should carefully check proclamation details.

The ecological dynamics of decision-making in sailing

Competitive sailing is characterised by continuous interdependencies of decisions and actions. All actions imply a permanent monitoring of the environmental conditions, such as intensity and direction of the wind, sea characteristics, and the behaviour of the opponent sailors. These constraints on sailors’ behavior are in constant change implying continuous adjustments in sailors’ actions and decisions. Among the different parts of a regatta, tactics and strategy at the start are particularly relevant. Among coaches there is an adage that says that “the start is 50% of a regatta” (Houghton, 1984; Saltonstall, 1983/1986). Olympic sailing regattas are performed with boats of the same class, by one, two or three sailors, depending on the boat class. Normally before the start, sailors visit the racing venue and analyse wind and sea characteristics, in order to fine- tune their boats accordingly. Then, five minutes before the start, sailors initiate starting procedures in order to be in a favourable position at the starting line (at the “second zero”). This position is selected during the start period according to wind shifts tendencies and the actions of other boats (Figure 11.1). Only after the start signal can the boats cross the imaginary starting line between the race committee signal boat “A” and the pin end boat. The start takes place against the wind (upwind), and the boats start racing in the direction of mark 1. Based on the evaluation of the sea and wind characteristics (e.g. if the wind is stronger at a particular place on the course), sailors re- adjust their strategy for the regatta. This strategy may change during the regatta, according to wind changes and adversary actions. More to the point, strategic decisions constrain and are constrained by on- line decisions during the regatta.